1 inch metal strips
[DOC File]PART 1
https://info.5y1.org/1-inch-metal-strips_1_dc0b63.html
Upstream Pressure Side: 0.0239 inch. Downstream Pressure Side: 0.0179 inch. Casing Lining: Secure lining to prevent delamination, sagging or settling. Lining shall be glued in place and captured by mechanically bonded metal barrier strips. Primary Air Inlet: Round stub connections shall be undersized by 1/8 inch for duct attachment.
[DOC File]SECTION 092216 - NON-STRUCTURAL METAL FRAMING
https://info.5y1.org/1-inch-metal-strips_1_837443.html
Tie Wire: ASTM A641/A641M, Class 1 zinc coating, soft temper, 0.062-inch- (1.57-mm-) diameter wire, or double strand of 0.048-inch- (1.21-mm-) diameter wire. Hanger Attachments to Concrete: ICC-ES AC01 and ICC-ES AC193 are for expansion anchors in masonry and mechanical anchors in concrete, respectively, and ICC-ES AC58 and ICC-ES AC308 are for ...
[DOC File]SECTION 03100 - Government of New York
https://info.5y1.org/1-inch-metal-strips_1_af1e01.html
Jul 24, 2018 · A. Chamfer Strips: Wood, metal, PVC or rubber; 1 inch chamfer, unless otherwise indicated on the Drawings. DELETE B. AND C. BELOW IF NOT REQUIRED. RUSTICATION, PATTERN OR FEATURE STRIPS FOR B. BELOW MUST BE DETAILED ON THE DRAWINGS. ADD SPECIFIC PRODUCT INFORMATION FOR TEXTURED STRIPS IF SELECTED BY DESIGNER.
[DOC File]Sectopm 07 62 00 - Sheet Metal Flashing and Trim
https://info.5y1.org/1-inch-metal-strips_1_c2441b.html
Aug 28, 2012 · Exposed Edges of Sheet Metal: Hem exposed edges on underside 1/2 inch; no raw edges will be permitted. Fabricate corners from one piece with minimum 18 inch long legs; seam for rigidity, seal with sealant. Fabricate vertical faces with bottom edge formed outward 1/4 inch (6 mm) and hemmed to form drip.
SECTION 07 42 13.13.03 – FORMED METAL WALL PANELS
Panel Thickness: 1-1/2 inch (38 mm). MISCELLANEOUS MATERIALS. General: Provide complete metal panel assemblies incorporating trim, copings, fasciae, gutters and downspouts, and miscellaneous flashings. Provide required fasteners, closure strips, and …
SECTION 074213.13 - FORMED METAL WALL PANELS
Closure Strips: Closed-cell, expanded, cellular, rubber or crosslinked, polyolefin-foam or closed-cell laminated polyethylene; minimum 1-inch- (25-mm-) thick, flexible closure strips; cut or premolded to match metal panel profile. Provide closure strips where …
[DOCX File]Manufactured Copings - Metal-Era
https://info.5y1.org/1-inch-metal-strips_1_e3d732.html
Metal-Era, Inc.May 2018. 1600 Airport Road. Waukesha, Wisconsin 53188. Phone800-558-2162. Fax800-373-9156. Websitewww.metalera.com. Emailinfo@metalera.com. Guide Specification. Specifier Notes: This guide specification is written in Construction Specifications Institute (CSI) 3-Part Format in accordance with The CSI Construction Specifications Practice Guide, MasterFormat, SectionFormat, …
[DOCX File]SECTION 05 31 00 STEEL DECKING - Veterans Affairs
https://info.5y1.org/1-inch-metal-strips_1_3e06b4.html
Fabricate cant strips from 1 mm (20 gauge) metal with a minimum 125 mm (5 inch) face width. 6.Seat Angles for Deck: Provide where a beam does not frame into a column. 7.Sump Pans for Roof Drains: Fabricate from single piece of minimum 1.9 mm (14 gauge) galvanized sheet steel with level bottoms and sloping sides to direct water flow to drain ...
[DOCX File]SECTION 05 31 00 - STEEL DECKING - Veterans Affairs
https://info.5y1.org/1-inch-metal-strips_1_72341b.html
Ridge and Valley Plates: Minimum 100 mm (4 inch) wide ridge and valley plates where roof slope exceeds 1/24 (1/2 inch per foot). Sheet Steel: Minimum 1.0 mm (0.04 inch) thick. Cant Strips: Provide bent metal 45 degree leg cant strips where indicated on the drawings.
[DOC File]SECTION 074213.53 - METAL SOFFIT PANELS
https://info.5y1.org/1-inch-metal-strips_1_d99a0a.html
Closure Strips: Closed-cell, expanded, cellular, rubber or crosslinked, polyolefin-foam or closed-cell laminated polyethylene; minimum 1-inch-thick, flexible closure strips; cut or premolded to match metal panel profile. Provide closure strips where indicated or necessary to ensure weathertight construction.
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.