1 polished stainless steel tubing
[DOC File]SECTION 15411-DOCS
https://info.5y1.org/1-polished-stainless-steel-tubing_1_f236b7.html
Assemblies consist of AISI Type 302/304 stainless steel tubing with integrally welded mounting flanges secured to concealed tenon plates with vandal-resistant fasteners, and complying with the following requirements: 1. Tubing: Stainless steel, 1-1/2 inch od x 18 gage wall thickness. Bend tubing …
[DOCX File]SECTION 10 28 00 - TOILET, BATH, AND LAUNDRY …
https://info.5y1.org/1-polished-stainless-steel-tubing_1_c5b242.html
Stainless steel tubing, minimum 1.27 mm (0.050 inch) wall thickness, 32 mm (11/4 inch) outside diameter. Flanges, stainless steel rings, 66 mm (2.6 inch) minimum outside diameter, with 2 holes opposite each other for 6 mm (1/4 inch) stainless steel …
[DOC File]SECTION 231123 - FACILITY NATURAL-GAS PIPING
https://info.5y1.org/1-polished-stainless-steel-tubing_1_0d4620.html
Corrugated, Stainless-Steel Tubing Complying with ANSI/IAS LC 1//CSA 6.26, and Protective Jacket System Complying with ICC-ES PMG LC 1027. See Editing Instruction No. 1 in the Evaluations for …
[DOCX File]www.arcat.com
https://info.5y1.org/1-polished-stainless-steel-tubing_1_413f7c.html
Bottom Rail: Stainless steel structural tubing, 2 inch (50 mm) diameter, Type 316 stainless steel. ** NOTE TO SPECIFIER ** Specify required finish from the following paragraphs and delete those not required. Stainless Steel Finish: Brushed. Polished. Baluster: Stainless Steel Structural Tubing, 1/2 inch (13 mm) diameter, Type 316 stainless steel.
[DOCX File]PART 1 – GENERAL
https://info.5y1.org/1-polished-stainless-steel-tubing_1_6d0174.html
Plunger assembly shall be turned and polished seamless steel tubing. Cylinder assembly shall be steel tubing with minimum 3.0 mil thickness, rust-inhibitive, factory-applied, prime paint followed by double …
X-Flo76
Close the integrated stainless steel clamp by depressing the colored handle. Attach a piece of #16 tubing, approximately 18’ in length, to the feed barb located in the center of the top manifold. Attach a piece of #16 tubing…
[DOCX File]Tubing Applications for the connection lab equipment When ...
https://info.5y1.org/1-polished-stainless-steel-tubing_1_aaa2f5.html
Stainless steel tubing. Acceptable for use with Inert gases, flammable gases, compressed air, lab water, house vacuum systems Coiled stainless tubing is available in most common sizes used in labs it …
[DOC File]SECTION 15411 - Government of New York
https://info.5y1.org/1-polished-stainless-steel-tubing_1_71c9fd.html
2. Brass tubing: 18 B & S gage. 3. Stainless steel: 18-8 Type 302 or 304 unless otherwise specified. D. Fixture Trim Finishes: 1. Brass or Bronze: Polished or satin finished chrome plating, 0.02 mil chromium over 0.2 mil nickel plating. 2. Stainless Steel: Invisible welds and seams, and unless otherwise specified, polished …
[DOC File]SECTION 102813.13 - COMMERICIAL TOILET ACCESSORIES
https://info.5y1.org/1-polished-stainless-steel-tubing_1_d4f7c2.html
857 Exposed mounting 1 inch o.d. 18 ga stainless steel tubing. 3-1/8 inch diameter 11 ga flanges; With mounting kit. 001-18, 001-24 configurations are third party tested to 900 pounds. [High polish finish -4] …
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.