10 inch clear glass plates
[DOC File]SECTION 096200 - Technical Glass Products
https://info.5y1.org/10-inch-clear-glass-plates_1_00ac66.html
Provide the system with a multi laminate walking surface glass with a non-slip frit applied to the number one surface. Span Width: [10 feet] [20 feet] Face Width: 3-1/8-inch wide. Adjust fire rating minutes in paragraphs below to suit Project if a fire rating is not required delete the paragraph and sub paragraph. Structural Performance
[DOC File]SECTION 084226 - ALL-GLASS ENTRANCES
https://info.5y1.org/10-inch-clear-glass-plates_1_6a3a3c.html
Generally, clear glass is used for interior vestibules, tinted glass for exterior locations. Verify thickness required for glass areas; 3/8-inch- (10-mm-) thick glass is available in limited sizes. Class 1: Clear …
[DOC File]SECTION 084126 - ALL-GLASS ENTRANCES AND STOREFRONTS
https://info.5y1.org/10-inch-clear-glass-plates_1_b524ba.html
Deflection Limits: Deflection normal to glazing plane is limited to [1 inch (25 mm)] [1/175 of clear span or 3/4 inch (19 mm), whichever is smaller] . Retain "Seismic Performance" Paragraph below for projects requiring seismic design.
[DOC File]Guide for Writing Outline Specifications
https://info.5y1.org/10-inch-clear-glass-plates_1_c5a17e.html
Provide 1-inch sealed insulated glass, made up of 1/4-inch thick clear float glass with e2 coating on interior panes of South and East walls. Provide heat mirror glass units on North walls. Use tempered glass where required. DIVISION 9: FINISHES 092216 NON-STRUCTURAL METAL FRAMING. Metal stud wall and ceiling framing. 092900 GYPSUM BOARD
[DOC File]FIRE PROTECTION & LIFE SAFETY DESIGN MANUAL
https://info.5y1.org/10-inch-clear-glass-plates_1_2f14c7.html
Hydrants must be installed with not less than 6-inch (65 mm) connection to the supply main, and valved at the connection. Barrels must be long enough to permit at least 18-inch (450 mm) clearance between the center of the 4-1/2-inch (115 mm) suction connection and grade. The ground must be graded so that any surface drainage is away from the ...
[DOC File]CSI SPECIFICATION 08955 - Technical Glass Products
https://info.5y1.org/10-inch-clear-glass-plates_1_819129.html
Seal glass units continuously on both sides of glass between frame and glass and between linear glass units. Joint Sealant: Install perimeter joint sealant and backing materials between assemblies and adjacent construction. Erection Tolerances: Limit Variations from Plumb and Level: 3 mm in 3000 mm [(1/8 inch in 10 feet)] vertically.
[DOCX File]SECTION 08 32 13, ICU SLIDING GLASS DOORS
https://info.5y1.org/10-inch-clear-glass-plates_1_b9492c.html
Class II, clear anodic finish and Class I, dark-bronze, color anodic finish are standard with many manufacturers. ... Face plates shall be high impact polycarbonate or stainless steel, engraved with waving hand logo and “Wave To Open” text. ... Variation from Plumb, Level, Warp, and Bow: Maximum 3 mm in 3 meters (1/8 inch in 10 feet ...
[DOC File]ARCAT spec 10503pen 2008-2-5
https://info.5y1.org/10-inch-clear-glass-plates_1_59c65e.html
Aug 01, 2016 · Openings 24 inches (609.6 mm) deep: Two heavy duty 7/8 inch x 2-1/4 inch x 3 inch single prong wall hooks and one 1 inch diameter coat rod. 2.06 ACCESSORIES A. Number Plates: Provide each locker with a polished aluminum number plate, 2-1/4 inches (57 mm) wide by 1 inch (25 mm) high, with black numerals not less than 3/8 inch (9.5 mm) high ...
League City Building Department
10.5 Main disconnect located at exterior of building next to meter, not higher than 6’-7” above grade. 10.6 Proper meter can per utility provider, HL&P, or Texas New Mexico. Service panel is weather tight and no slots are left open in panel. 10.7 A minimum clear space …
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.