10 inch galvanized duct pipe
[DOC File]SECTION 232000 - HVAC PIPING
https://info.5y1.org/10-inch-galvanized-duct-pipe_1_d034d5.html
GALVANIZED STEEL PIPE. Pipe: Schedule 40 in accordance with ASTM A120. Fittings: 150-pound screwed galvanized malleable iron on 2 inches and below. Mechanical couplings as herein specified on 2 1/2 inches and above. Service: Miscellaneous indirect waste piping. BLACK STEEL PIPE, SCHEDULE 80. Pipe: Schedule 80, in accordance with ASTM A120 or A53.
[DOCX File]SECTION 23 05 29
https://info.5y1.org/10-inch-galvanized-duct-pipe_1_1e4944.html
Hangers for Hot and Cold Pipe Sizes 1/2 to 11/2 Inch, Carbon steel, adjustable swivel, band type. ... galvanized-steel, clevis-type pipe hangers. ... Pipe and duct sleeves are not required for penetrations through non-rated concealed partitions.
[DOCX File]Section 23 31 00 - HVAC DUCTS AND CASINGS
https://info.5y1.org/10-inch-galvanized-duct-pipe_1_cd63d6.html
2.Rectangular Duct: Galvanized steel, minimum 1.0 mm (20 gage), Pittsburgh lock seam, companion angle joints 32 mm by 3.2 mm (11/4 by 1/8 inch) minimum at not more than 2.4 m (8 feet) spacing. Approved pre-manufactured joints are acceptable in lieu of companion angles.
[DOC File]SECTION 15820 - DUCT ACCESSORIES
https://info.5y1.org/10-inch-galvanized-duct-pipe_1_cada10.html
2.10 DUCT-MOUNTED ACCESS DOORS AND PANELS 7. 2.11 FLEXIBLE CONNECTORS 8. ... galvanized steel pipe rotating within a pipe-bearing assembly mounted on supports at each mullion and at each end of multiple-damper assemblies. ... of straight duct, at 500 Hz, based on 150 mm (6 inch) duct, of 750 m/min (2500 fpm).
[DOC File]SECTION 210529 - HANGERS AND SUPPORTS FOR FIRE …
https://info.5y1.org/10-inch-galvanized-duct-pipe_1_2737c9.html
Hangers for Pipe Sizes 2 Inches (50.8 mm) and Cold Pipe Sizes 6 Inches (152.4 mm) and Over: Carbon steel, black or galvanized, adjustable, clevis, UL listed, Grinnell Fig. 260 or equal. Hangers for Hot Pipe Sizes 6 Inches (152.4 mm) and Over: Adjustable steel yoke, cast iron roll, double hanger.
[DOC File]SECTION 230529 - HANGERS AND SUPPORTS FOR HVAC …
https://info.5y1.org/10-inch-galvanized-duct-pipe_1_d2208a.html
The overall height for each support shall be eighteen (18) inches from the finished roof to the top of the counterflashing plus the height of the pipe supports and the pipe. Contractor shall provide galvanized Unistrut type channel tracts, with galvanized washers, nuts, bolts, and pipe clamps to secure the ductwork to the tract and the track to ...
SECTION 260533 - ELECTRICAL CONDUIT
Conduit straps: P2580-10 to P2553-40, two holes type. Conduit straps: Appleton, Steel City, or equal, one-hole, sheet steel, for 1/2 and 3/4-inch conduits only. "U" bolts: Schedule 40 pipe sizes with threaded legs and nuts. Universal pipe clamps, 1/2 to 2 inches (13 to 50 mm) conduits: P2911 to P2917. I.P.S. type pipe hangers as shown. WARNING TAPE
[DOC File]Section 15010 - Mechanical General - Kinetics Noise
https://info.5y1.org/10-inch-galvanized-duct-pipe_1_fae5b3.html
Ensure pipe, duct and electrical connections to isolated equipment do not reduce system flexibility. Ensure that pipe, conduit and duct passing through walls and floors do not transmit vibrations. Unless indicated otherwise, piping connected to isolated equipment shall be isolated as follows: Up to (NPS) 4” Diameter: first 3 points of support.
[DOC File]SECTION 233113 – DUCTS AND DUCT ACCESSORIES
https://info.5y1.org/10-inch-galvanized-duct-pipe_1_198314.html
SECTION 233113 – HVAC DUCT SYSTEMS AND ACCESSORIES. First Edition 5-16-2017 (Engineer shall edit specifications and blue text in header to meet project requirements. This includes but is not limited to updating Equipment and/or Material Model Numbers indicated in the specifications and adding any additional specifications that may be required ...
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.