5 horsepower electric compressor motor

    • [DOCX File]Air Compressors

      https://info.5y1.org/5-horsepower-electric-compressor-motor_1_624a0d.html

      Air-cooled compressors pass the hot lubricating oil from the compressor and compressed air through finned-tube heat exchangers and force ambient air across the heat exchangers using a cooling air fan. Cooling fan horsepower is typically about 5% of the power of the compressor motor.


    • [DOC File]CHAPTER 2

      https://info.5y1.org/5-horsepower-electric-compressor-motor_1_063738.html

      (5) Electric requirements (kW demand) of auxiliaries. (6) Electric requirements (kW demand) of electric motor. driven compressors. (7) EFLH for the project's location should be. distributed monthly to the cooling system. Table VI. is a recommended EFLH distribution for selected. large cities. (8) Make-up water requirements for air-conditioning


    • [DOC File]Heading - DMC GAS

      https://info.5y1.org/5-horsepower-electric-compressor-motor_1_03acb5.html

      LGRL1.25, LGL1.25 & LGL1.5 Pumps. Motor Speed Pumps for Motor Fueling and Multi-Cylinder Filling. These durable motor speed pumps offer capacities from 9 to 35 U.S. gpm (34-132 lpm), and are ideal for motor fueling, multiple-station cylinder filling. and a variety of small transfer jobs. The LGL models are designed for foot. mounting to a ...


    • [DOC File]AVON INFORMATION

      https://info.5y1.org/5-horsepower-electric-compressor-motor_1_bb02f2.html

      The gas generator, is started by an electric motor in the plenum chamber which is coupled to the gas generator starter drive mechanism mounted on the front of the compressor shaft. This mechanism is a ratchet and pawl type arrangement that disengages by centrifugal force when the gas generator speed exceeds the starting motor speed.


    • [DOCX File]SECTION 23 84 00 - HUMIDITY CONTROL EQUIPMENT

      https://info.5y1.org/5-horsepower-electric-compressor-motor_1_65e5d5.html

      2.Electric motor shall be fractional-horsepower with close-coupled speed reducer and a belt drive with belt tensioning system for the thermal wheel. E.Controls and Wiring: Factory-installed microprocessor type to control and monitor unit and communicate to central-control processor and shall operate dehumidification units and maintain humidity ...


    • [DOC File]Guide Specification Smardt water Cooled Chillers

      https://info.5y1.org/5-horsepower-electric-compressor-motor_1_56ce82.html

      2. Compressor motor and chiller unit shall include variable-frequency speed controls to match cooling load demand to compressor speed and inlet guide vane position. 3. Each compressor shall be equipped with a 5% impedance AC line reactor and individual disconnect or circuit breaker. 4.


    • [DOC File]SPECIFICATION GA55-90C FF ICD - Atlas Copco

      https://info.5y1.org/5-horsepower-electric-compressor-motor_1_85dc38.html

      This specification is for a belt driven, oil-lubricated, single-stage air cooled rotary screw air compressor. The compressor shall be a 15 horsepower Atlas Copco model GA11 or pre-approved equivalent. The compressor shall deliver 57.0 acfm at 125 psi in accordance with ISO 1217, Annex C. acfm is actual cubic feet per minute at inlet conditions.


    • [DOC File]SPECIFICATION GA55-90C FF ICD - Atlas Copco

      https://info.5y1.org/5-horsepower-electric-compressor-motor_1_c8ca56.html

      The compressor shall be a 150 horsepower Atlas Copco model GA110VSD+ or pre-approved equivalent. The compressor shall deliver 116.7 to 682.0 acfm at 125 psi in accordance with ISO 1217, Annex E. acfm is actual cubic feet per minute at inlet conditions.


    • Electricity for Refrigeration, Heating and Air ...

      Charges 22 2.3 Flow of Electrons 23 2.4 Conductors and Insulators 26 2.5 Electric Potential 27. ... The horse- power conversion is used to calculate the horsepower of a motor only if the watts are known. ... In Figure 3.13 the compressor, condenser fan motor, and indoor fan motor are connected in parallel to the supply voltage L1 and L2. ...


    • [DOC File]Industrial Compressed Air System Description

      https://info.5y1.org/5-horsepower-electric-compressor-motor_1_18d2fa.html

      The compressor mass flow and actual cubic feet per minute (acfm) capacity at a given discharge pressure increases as the ambient temperature decreases. Typically, a capacity control system is provided with the compressor to maintain the desired capacity and to operate within the motor horsepower limits.


    • [DOC File]Ag Miscellaneous Equipment Application Form

      https://info.5y1.org/5-horsepower-electric-compressor-motor_1_617366.html

      Metal Parts Coating* HVLP, roller, and brush*Universal N/A* 5 hp* 5 hp electric air compressor* N/A* 10 gal/yr* 5. Dryer* Maxon Mpakt Two at 1.5 MMBtu/hr* Natural gas* N/A* < 1,000 hr/yr* *Note: The first five rows are presented as examples. See instructions for further information.


    • [DOC File]VIKING PRODUCT SPECIFICATIONS

      https://info.5y1.org/5-horsepower-electric-compressor-motor_1_5d1ab4.html

      Sprinkler systems requiring an air supply with a capacity of 150 gallons or less shall be equipped with a riser mounted, electric motor-driven, air-cooled, single-stage, oil-less compressor. Air compressor motor shall be ¼ horsepower in size and produce 1.5 SCFM at 50 PSI. The field adjustable pressure range of air compressor shall be 14-60 PSI.


    • [DOC File]Power Cost hours x kWh x bhp x - air compressor s

      https://info.5y1.org/5-horsepower-electric-compressor-motor_1_5aaa5c.html

      Electrical cost = HP x .746 x hours x Kw cost / motor efficiency. Example: 50 hp air compressor that runs 8 hours a day 5 days a week for a year with a $.06 Kw electric rate and a 90% efficient electric motor. 50 hp x .746 x 2080 hours x $.06 / .90 = $5,172.27 per year.



    • [DOCX File]Section 22 61 19.74 - DENTAL COMPRESSED-AIR EQUIPMENT

      https://info.5y1.org/5-horsepower-electric-compressor-motor_1_fa724b.html

      Compressor drive and motor shall be V-belt driven through a combination flywheel/sheave and steel motor sheave with tapered bushing and protected by an OSHA approved, totally enclosed belt guard. Belt tensioning shall be achieved by a pivoting motor mounting base that is fully adjustable through twin adjusting screws.


Nearby & related entries: