6 inch galvanized duct pipe: free download. On-line document store on 5y1.org

[DOCX File]SECTION 23 05 29
https://info.5y1.org/6-inch-galvanized-duct-pipe_1_1e4944.html
Multiple or Trapeze Hangers for Hot Pipe Sizes 6 Inches and Over: Steel channels with welded spacers and hanger rods, cast iron roll. Wall Support for Hot Pipe Sizes 6 Inches (150 mm) and Over: Welded steel bracket and wrought steel clamp with adjustable steel yoke and cast iron roll.
6 ductwork pipe

[DOC File]PART 1
https://info.5y1.org/6-inch-galvanized-duct-pipe_1_2b6e4a.html
Provide 6 inch long flexible duct connectors at all duct connections to rotating or vibrating equipment such as outside air pretreatment units, etc. Refer to Section 15810 - Ducts. When the installation of rooftop PTUs or piping is unavoidable, permission and a waiver shall be requested from the SBBC Design Services Department.
6 inch galvanized vent pipe

SECTION 230529 - HANGERS AND SUPPORTS FOR HVAC …
Hangers for Pipe Sizes 2 Inches (50.8 mm) and Cold Pipe Sizes 6 Inches (152.4 mm) and Over: Carbon steel, black or galvanized, adjustable, clevis, UL listed, Grinnell Fig. 260 or equal. Hangers for Hot Pipe Sizes 6 Inches (152.4 mm) and Over: Adjustable steel yoke, cast iron roll, double hanger.
6 metal ductwork

[DOCX File]Section 23 31 00 - HVAC DUCTS AND CASINGS
https://info.5y1.org/6-inch-galvanized-duct-pipe_1_cd63d6.html
4.For cleaning operating room supply air duct and kitchen hood exhaust duct, locate access doors at 6 m (20 feet) intervals and at each change in duct direction. B.Openings shall be as large as feasible in small ducts, 300 mm by 300 mm (12 inch by 12 inch) minimum where possible.
6 inch round duct pipe

[DOC File]ELECTRICAL CONDUIT SYSTEM
https://info.5y1.org/6-inch-galvanized-duct-pipe_1_68e144.html
For the outer duct of RGC multi-cell raceway, use rigid galvanized conduit per UL 6 “Rigid Metallic Conduit” with rigid full weight galvanized threaded fittings. Provide factory installed reverse-spin couplings with 3 set screws, to allow assembly without turning the outer duct, and prevent the coupling from backing off before and after ...
6 heat duct

[DOC File]SECTION 210529 - HANGERS AND SUPPORTS FOR FIRE …
https://info.5y1.org/6-inch-galvanized-duct-pipe_1_2737c9.html
Hangers for Pipe Sizes 2 Inches (50.8 mm) and Cold Pipe Sizes 6 Inches (152.4 mm) and Over: Carbon steel, black or galvanized, adjustable, clevis, UL listed, Grinnell Fig. 260 or equal. Hangers for Hot Pipe Sizes 6 Inches (152.4 mm) and Over: Adjustable steel yoke, cast iron roll, double hanger.
6 inch metal ducting

[DOC File]SECTION 232000 - HVAC PIPING
https://info.5y1.org/6-inch-galvanized-duct-pipe_1_d034d5.html
GALVANIZED STEEL PIPE. Pipe: Schedule 40 in accordance with ASTM A120. Fittings: 150-pound screwed galvanized malleable iron on 2 inches and below. Mechanical couplings as herein specified on 2 1/2 inches and above. Service: Miscellaneous indirect waste piping. BLACK STEEL PIPE, SCHEDULE 80. Pipe: Schedule 80, in accordance with ASTM A120 or A53.
6 round duct

[DOC File]SECTION 233113 – DUCTS AND DUCT ACCESSORIES
https://info.5y1.org/6-inch-galvanized-duct-pipe_1_198314.html
SECTION 233113 – HVAC DUCT SYSTEMS AND ACCESSORIES. First Edition 5-16-2017 (Engineer shall edit specifications and blue text in header to meet project requirements. This includes but is not limited to updating Equipment and/or Material Model Numbers indicated in the specifications and adding any additional specifications that may be required ...
6 inch galvanized stove pipe

6 inch galvanized duct pipe