Aluminum in contact with galvanized steel: free download. On-line document store on 5y1.org

[DOC File]SECTION 02444
https://info.5y1.org/aluminum-in-contact-with-galvanized-steel_1_461bac.html
Tie Wire: Galvanized or aluminum-coated 0.148 inch steel wire, or aluminum alloy conforming to ASTM B211, 1100-H14. Hog Rings: Galvanized or aluminum-coated 0.120 inch steel wire, or aluminum conforming to ASTM B221, 6061-T6. Aluminum coating: minimum 0.24 …
aluminum and steel contact

[DOCX File]ARCAT, Inc.
https://info.5y1.org/aluminum-in-contact-with-galvanized-steel_1_937156.html
Minimum 22-gauge B&S aluminum. Minimum 24-gauge galvanized steel. Minimum 24-gauge stainless steel. Hood Finish: ** NOTE TO SPECIFIER ** Select one of the following paragraphs for hood finish and delete those not required.; Polyester top coat is standard on galvanized steel hood . Galvanized steel with polyester top coat in choice of:
aluminum against galvanized steel

[DOCX File]ARCAT | Free Building Product CAD Details, BIM, Specs and …
https://info.5y1.org/aluminum-in-contact-with-galvanized-steel_1_df2750.html
End Stiles: 20 gauge galvanized steel up to 24 feet 2 inches (7366 mm) wide. 16 gauge galvanized steel over 24 feet 2 inches (7366 mm) wide. Insulation: 95 percent closed cell, foamed-in-place polyurethane with thermal break. Air Filtration 0.15 in accordance of ANSI/DASMA 105 ASTM E283 standards.
galvanized steel and aluminum corrosion

[DOCX File]Perforated Metal Panels - Steel Gates | Aluminum Fence
https://info.5y1.org/aluminum-in-contact-with-galvanized-steel_1_73252e.html
***** Steel sheets can be supplied with bare galvanized finish or galvanized sheets and panels can be coated with either polyester powder o. r. polyurethane color coating. ***** 1.Hot-dip galvanized zinc coating in accordance with ASTM A123. ***** Polyester powder color coating is applicable for steel, galvanized steel, stainless steel, and ...
galvanized steel touching aluminum

[DOCX File]SECTION 07 60 00, FLASHING AND SHEET METAL
https://info.5y1.org/aluminum-in-contact-with-galvanized-steel_1_b285b8.html
SPEC WRITER NOTE: If prefinished galvanized steel copings are used change par C title and specify as if aluminum with sealant in lieu of solder. //Stainless steel// //Copper// Copings: Join ends of sheets by a 19 mm (3/4 inch) locked and soldered seam, except at intervals of 9600 mm (32 feet), provide a 38 mm (1 1/2 inch) loose locked expansion ...
aluminum and galvanized corrosion

[DOCX File]SECTION 08411 - ALUMINUM-FRAMED ENTRANCES AND …
https://info.5y1.org/aluminum-in-contact-with-galvanized-steel_1_0a5087.html
Mullions between entrance doors will have 3/16” continuous galvanized steel channel or tube reinforcement the full height of door to provide stiffening and anchorage for strike hardware. Removable mullions may be used only when specifically authorized by MSU. ... Where aluminum will contact dissimilar metals, protect against galvanic action ...
can aluminum touch galvanized steel

[DOCX File]SECTION 08 90 00 - LOUVERS AND VENTS
https://info.5y1.org/aluminum-in-contact-with-galvanized-steel_1_3fe646.html
Galvanized-steel sheet for galvanized-steel louvers, 1.02 mm (0.040 inch) minimum. Stainless-steel sheet for stainless-steel louvers, not less than 0.95 mm (0.038 inch) minimum. Insulated laminated panels consisting of an insulating core surfaced on back and front with metal sheets and attached to back of louver with clips on screws and ...
can aluminum and steel touch

[DOCX File]Metal Sun Shades - Steel Fence | Steel Gates | Aluminum Fence
https://info.5y1.org/aluminum-in-contact-with-galvanized-steel_1_c84aac.html
3.ASTM A526 - Sheet Steel, Zinc-Coated (Galvanized) by the Hot-Dip Process, Commercial Quality. 4.ASTM A792 - Steel Sheet, 55% Aluminum-Zinc Alloy-Coated by the Hot-Dip Process. 5.ASTM B117 - Standard Practice for Operating Salt Spray (Fog) Apparatus. 6.ASTM B209 - Aluminum and Aluminum-Alloy Sheet and Plate.
galvanized steel and aluminum compatibility

Aluminum in contact with galvanized steel