Astm rounding rules for decimals
[DOCX File]2021 Certified LPA General Conditions Template
https://info.5y1.org/astm-rounding-rules-for-decimals_1_0064b1.html
The Contractor shall comply with the rules of the Oregon Utility Notification Center, OAR 9520010010 through OAR 952-001-0090, and ORS 757.993. The Contractor may contact the Oregon Utility Notification Center at 503232-1987 about these rules. 00150.55 Cooperation with Other Contractors
[DOC File]MASTER COAL PURCHASE AND SALE AGREEMENT
https://info.5y1.org/astm-rounding-rules-for-decimals_1_13e69e.html
10.5 Rounding and Significant Digits. All calculations will use floating decimals with the final operation being rounded to the significant digits to the right of the decimal place as follows: Btu/lb. will be zero (0) nn,nnn. Grindability will be zero (0) nn. Emission Allowances will be …
[DOC File]telefaks - Smučarska zveza Slovenije | Smučarska zveza ...
https://info.5y1.org/astm-rounding-rules-for-decimals_1_f3c7f7.html
901.2.4 The Giant Slalom has to be set as follows (number of direction changes by rounding up or down of the decimals): - Children: 13% - 15% of the vertical drop. 903.1.4 The course setter in setting the course for children should take particular consideration of the physical ability of the competitors.
2018 LPA General Conditions Template
- The special directions, provisions, and requirements specific to a Project that supplement or modify the Standard Specifications. Permits and orders governing the Project that are issued directly to the Owner by a governmental or regulatory authority are considered to be part of the Special Provisions, to the extent and under the conditions stipulated in the Special Provisions.
Table of Contents
The rounding rules in NIST Handbook 130, “Uniform Packaging and Labeling Regulations” permit packers to round declarations up or down based on their knowledge of their package filling targets and the accuracy of packaging equipment. Determine the larger of the values by converting the SI declaration to inch-pound units, or vice versa, using ...
[DOCX File]2017 Tax Credit Application Instructions Final
https://info.5y1.org/astm-rounding-rules-for-decimals_1_4c4d72.html
The Oklahoma Housing Finance Agency (OHFA) QAP consists of the Application Instructions, Application Form, and Title 330, Chapter 36 Affordable Housing Tax Credit (AHTC) Program Rules. In any instance where there is a conflict between the Rules and the Instructions and/or the Application Form, the Rules …
[DOC File]DEPARTMENT OF ENVIRONMENTAL PROTECTION
https://info.5y1.org/astm-rounding-rules-for-decimals_1_c3fa37.html
Analysis of each laboratory sample for percent moisture must be conducted in accordance with ASTM D3173 73(79) (or the most recent version of the procedure available on the implementation date of this manual) or the appropriate portion of ASTM D3302 (or the most recent version of the procedure available on the implementation date of this manual).
[DOCX File]NFRC Procedures Template
https://info.5y1.org/astm-rounding-rules-for-decimals_1_b3185f.html
All grouping rules contained in Section 4 shall be permitted to be utilized with the calculation procedures of Section 5.6. ... Follow the NFRC-approved procedure for rounding the final result. The SHGC and VT rating shall be reported to X.XX decimals. All variables used in the formula shall be expressed to at least three significant decimal ...
[DOC File]SOM - State of Michigan
https://info.5y1.org/astm-rounding-rules-for-decimals_1_2c4564.html
(d) All decimals must be rounded to two decimal places, with five and greater rounding up and four and less rounding down, unless otherwise specified. 2.243 Liquidated Damages The parties acknowledge that late or improper completion of the Work will cause loss and damage to the State, and that it would be impracticable and extremely difficult to fix the actual damage sustained by the State as a result.
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.