Basic switch configuration cisco
[PDF File]Basic Router Configuration - Cisco
https://info.5y1.org/basic-switch-configuration-cisco_1_bc2e7a.html
Module Title: Basic Switch and End Device Configuration Module Objective: Implement initial settings including passwords, IP addressing, and default gateway parameters on a network switch and end devices. Topic Title Topic Objective Cisco IOS Access Explain how to access a Cisco IOS device for configuration purposes. IOS Navigation Explain how to navigate Cisco IOS to configure network …
[PDF File]Basic Switching Concepts and Configuration
https://info.5y1.org/basic-switch-configuration-cisco_1_308b2d.html
Basic Cisco Commands By Marcus Nielson (2014) Configuring Basic Switch Settings (Switch Examples) Enter enable if the prompt has changed back to Switch>. Switch> enable Switch# Enter global configuration mode. Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# The prompt changed again to reflect global configuration mode. Assign the …
[PDF File]Module 2: Basic Switch and End Device Configuration
https://info.5y1.org/basic-switch-configuration-cisco_1_87e815.html
Basic Router/Switch IOS commands: Interface Configuration: Router(config)#default int range fa 0/0 - 1 !(to clear all int config back to default)!(space b/w fa and -) Router(config)#default int range fa 0/0 – 1, fa 0/4 - 5 Router(config)#int fa 0/0 Router(config-if)#mac-address 0000.1111.1111 !(hard code a mac address for ease of use) Router(config-if)#ip address 192.168.1.1 255.255.255.0 ...
Basic Cisco Switch Configuration Example in 10 Steps
What is the Cisco IOS version that the switch is running? _____ What is the system image filename? _____ What is the base MAC address of this switch? _____ Step 4: Examine the Fast Ethernet interfaces. Examine the default properties of the Fast Ethernet interface used by PC1. Switch# show interface fastethernet 0/18 Is the interface up or down? _____ What event would make an interface go …
[PDF File]Basic Router/Switch IOS commands: Interface Configuration ...
https://info.5y1.org/basic-switch-configuration-cisco_1_68cc99.html
Step 3: Configure the system to boot using a different Cisco IOS image. In global configuration mode, issue this command. S1(config)#boot system flash:c2960-lanbase-mz.122-25.SEE1.bin ...
[PDF File]Lab Configuring Basic Switch Settings (Solution)
https://info.5y1.org/basic-switch-configuration-cisco_1_7a99b0.html
Basic Router Configuration This chapter provides procedures for configuring the basic parameters of your Cisco router, including global parameter settings, routing protocols, interf aces, and command-line access. It also describes the default configuration on startup. Note Individual router models may not support every feature described throughout this guide. Features not supported by a ...
[PDF File]Configuring the Switch for the First Time - Cisco
https://info.5y1.org/basic-switch-configuration-cisco_1_2b7ca4.html
2.1 Basic Switch Configuration 2.1.1 Configure a Switch with Initial Settings 2.1.1.1 Switch Boot Sequence After a Cisco switch is powered on, it goes through the following boot sequence: 1. First, the switch loads a power-on self-test (POST) program stored in ROM. POST checks the CPU subsystem. It tests the CPU, DRAM, and the portion of the flash device that makes up the flash file system. 2 ...
[PDF File]Basic Switching Concepts and Configuration
https://info.5y1.org/basic-switch-configuration-cisco_1_68d361.html
Basic Switch Configuration (2.1) Basic switch administration should be mastered by a switch administrator. This includes familiarity with the hardware as well as basic port configuration. Configure a Switch with Initial Settings (2.1.1) In this section, you learn the Cisco switch boot sequence, how to recover from a sys-
[PDF File]Basic Cisco Commands - Weber State University
https://info.5y1.org/basic-switch-configuration-cisco_1_580055.html
In Part 2, you will configure basic settings for the switch and PC. Step 1: Configure basic switch settings. a. Copy the following basic configuration and paste it into S1 while in global configuration mode. no ip domain-lookup hostname S1 service password-encryption enable secret class banner motd # Unauthorized access is strictly prohibited.
[PDF File]Lab 2.5.1: Basic Switch Configuration
https://info.5y1.org/basic-switch-configuration-cisco_1_f3b233.html
the “IP Addressing and Services” section in the Cisco IOS IP and IP Routing Configuration Guide for Cisco IOS Release 12.1 for additional information about configuring DHCP. About DHCP-Based Autoconfiguration Note Starting with Release 12.2(20) EW, you can enable DHCP AutoConfiguration by entering the write erase command. This command clears the startup-config in NVRAM. In images …
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.