Bat set command
[DOC File]PI Batch Generator (PIBaGen) Interface to the PI System
https://info.5y1.org/bat-set-command_1_1be528.html
Command-line arguments can begin with a / or with a -. For example, the /host=localhost and –host=localhost command-line arguments are equivalent. For Windows, command file names have a .bat extension. The Windows continuation character (^) allows one to use multiple lines for the startup command.
[DOC File]Batch Programming in the OMSA CLI
https://info.5y1.org/bat-set-command_1_b31d37.html
The CLI uses words to request reports, set systems management information, change bios settings, update bios or firmware etc. Basically, any systems management configuration that can be changed using the Web-based interface can also be changed using the command line interface.
[DOC File]The PC Boot Process
https://info.5y1.org/bat-set-command_1_e4a65c.html
BUFFERS=20 (set aside 20 512-byte areas to speed up disk access and program execution) LASTDRIV=z (reserve up to 26 drive letters, A through Z. DEVICE=MOUSE.SYS (load mouse driver -- can also be done from AUTOEXEC) AUTOEXEC.BAT contains a batch of startup DOS commands, executed by COMMAND.COM. Typical minimal AUTOEXEC.BAT
[DOC File]PI Batch File Interface (NT, VAX and UNIX)
https://info.5y1.org/bat-set-command_1_770a32.html
Command-line arguments can begin with a / or with a -. For example, the /ps=M and –ps=M command-line arguments are equivalent. Notes for NT. For NT, command file names have a .bat extension. The NT continuation character (^) allows one to use multiple lines for the startup command. The maximum length of each line is 1024 characters (1 kilobyte).
[DOC File]קובצי script של Windows (DOS)
https://info.5y1.org/bat-set-command_1_2ee994.html
Windows (DOS) המקביל ב-DOS ו-Windows לסקריפטים הם קובצי האצווה Batch files. ב-DOS לקבצים האלו היו תמיד סיומת .bat ב-Windows החדשים הם יכולים להיות גם בעלי סיומת .cmd אמצעי התכנות של …
PDMS- Command Syntax
This command orientates the arrive of the element in the. opposite direction to the leave of the previous element. It does. not change the position. CONNECT. Perform an ORI, then position the arrive at the leave of previous. DIR S. This is a special command which is allowed to change the angle. of a component. It first performs an ori, then ...
[DOC File]Batch File - NT and UNIX
https://info.5y1.org/bat-set-command_1_6dff34.html
REM end of batchfl.bat The following is a UNIX example: # # @(#)batchfl.sh 1.0 07/29/96 # # # this command procedure passes required -default parameters to # process batchfl. # # # command line arguments: # /f= required - frequency in seconds to check for new data files # /pa= required - path and mask to data fi. les
[DOC File]Foxboro Batch Interface to the PI System
https://info.5y1.org/bat-set-command_1_af34fe.html
retryTO=0 This command is used to set the timeout of the retry command. The default the value is set to 0 (timeout is not set). rst= Same as in startup command file. This command is used to set the target start time of the history data recovery process. Note: This command must be used in conjunction with the mode=recovery command.
[DOC File]Getting Started with DOS
https://info.5y1.org/bat-set-command_1_1774d5.html
The above command will delete all the addresses (remember, we set up addresses as documents or files) in the 99888 subdirectory. With 99888 free of contents, we can now remove it: c:\> rd alaska\sicily\99888. It is important to note that if you performed your file delete from within the 99888 directory . c:\alaska\sicily\99888> del *.*
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.