Can bus connector pinout
[DOCX File]Rochester Institute of Technology
https://info.5y1.org/can-bus-connector-pinout_1_4924d3.html
Jumper locations as seen from the back of the Bus Monitor PCB Misc. ECB Connector Pinout Bus Monitor Single Step Momentary Switch Connections Serial Cable for the CPU card. The N8VEM Z-80 CPU card requires a custom made serial cable. In my experience premade cables (10-PIN IDC to DB9) won’t work.
[DOC File]Auto diagnostic tool | Immo emulator | SRS emulator | EGR ...
https://info.5y1.org/can-bus-connector-pinout_1_e9e0c2.html
An optional alternate connection header is provided to allow one cable for data and power. Two jumpers will have to be set into the RS232 position above the DB-9 connector. Connector pinout is as follows: Pin 1 Vdc Pin 2 Tx Pin 3 Rx Pin 4 Ground 2.2.3 TTL communications. The LCD2041 can be talked to at TTL (logic 0V to +5V) levels.
[DOC File]VMEbus Connector Pin Assignment
https://info.5y1.org/can-bus-connector-pinout_1_c85d16.html
This document describes this connector and provides information on its pinout and source. MCC offers a variety of I2C based products. These products include our I2C Bus Monitor, iPort RS-232 to I2C Host Adapter, and iPack I2C Bus Cards. To provide a standard way to connect these products, we use the . Molex SEMCONNTM ACCESS.bus Connector
[DOC File]Proceedings - EDGE
https://info.5y1.org/can-bus-connector-pinout_1_0d7435.html
Connector x437 white Connector x437A blue . 1 = CAN 3 HI - Powertrain Bus 1 = 12V/5A (F219) 2 = CAN 4 HI - Body Faults Bus 2 = CAN4+ Body Fault 3 = K Bus ISO9141 single wire LIN 3 = CAN4- Body Fault 4 = CAN 6 HI Chassis Bus 7 = K/Serial 5 = CAN 2 HI Body Bus 9 = CAN2 Body + 6 = CAN 3 LO Powertrain Bus 10 = CAN2 Body- 7 = CAN 4 LO Body Faults ...
[DOC File]RetroBrew Computers
https://info.5y1.org/can-bus-connector-pinout_1_77096d.html
As described on the Cloning page, the OPC-478 cable interconnects your IC-R10 and your PC. The OPC-478 cable has a 9-pin D-sub connector on one end, and a 3,5 mm jack plug on the other. The D-sub connector connects to a 9-pin serial port on your PC whereas the jack plug goes (originally) into the earphone socket of your IC-R10.
[DOC File]iPort I2C Connector - mellottsvrpage
https://info.5y1.org/can-bus-connector-pinout_1_4594cf.html
The physical interface to the CAN bus are implemented using a DB9 connector. Female right angle DB9 connectors are placed on all the boards (both the controller interface board and the motor controller boards).
[DOC File]Introduction ||Connections LCD2041 || Displaying Text ...
https://info.5y1.org/can-bus-connector-pinout_1_f1da28.html
The Motor Module Controller subsystem and subsequent Motor Module subsystem are the logic and device systems for actuating a motor. The Motor Module Controller subsystem contains
CAN Bus Interface Description CANbus Pin Out, and Signal ...
Single height modules use only the P1/J1 connector, and can only monitor address lines A01-A23. This limits these modules to the A16, A24 and A40 cycles. Double height modules can monitor an additional eight address lines on the P2/J2 connector, so they can also perform 32 and 64-bit address transfers.
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.