Color ply laminated wood

    • [DOC File]SECTION 12710 - FIXED UPHOLSTERED SEATING

      https://info.5y1.org/color-ply-laminated-wood_1_a41917.html

      Plyform wood back. Back Assembly: The back assembly shall consist of a laminated plyform wood panel comprising the Classic Quattro ‘soft square” design with the top corners of the back conically shaped for stylish looks and timeless appearance and an ergonomic contour front surface to facilitate proper posture of a seated individual.


    • [DOCX File]This guide spec is intended to be used with “Architectural ...

      https://info.5y1.org/color-ply-laminated-wood_1_6f9126.html

      The drawer material defaults are: Wood Casework, Custom Grade – LPDL (melamine) or 7-ply hardwood veneer core plywood or solid hardwood, Premium Grade – prefinished Hardwood veneer core plywood or prefinished solid hardwood. PLAM casework, Custom Grade – LPDL (melamine) or HPDL, Premium Grade - 7-ply veneer core with HPDL faces.


    • [DOCX File]Clean soiled surfaces of - Navy Island, Inc.

      https://info.5y1.org/color-ply-laminated-wood_1_63f69a.html

      : Acoustic panels shall be as follows: The face skin is to be comprised of a (wood veneer, vinyl, decorative paper or other) which shall be laminated to a rigid backer sheet with a combined thickness of not less than 1.65mm (.065”) thick to provide adequate impact resistance for the panel.


    • [DOC File]Part 1 - General - Hufcor

      https://info.5y1.org/color-ply-laminated-wood_1_b0d13e.html

      A. Product to be top supported, center stacked, Series GT2 paired wood-framed glass panels as manufactured by Hufcor. 1. Panels shall be nominally 1-3/4" [43mm] thick and to 48" [1219] in width. 2. Wood frame of triple laminated solid wood top and bottom rails and stiles that are constructed from custom made veneers with an engineered wood core. a.


    • [DOC File]09 7710 – FRAMED DECORATIVE PANEL SYSTEMS

      https://info.5y1.org/color-ply-laminated-wood_1_708f59.html

      Marlite’s Flame Safe Panels are Class C and Class A construction 3-ply lamination with HPL faces on wood fiber substrate with a balancing backer. ... Non Fire-Rated HPL laminated to wood fiber substrate, with balancing backer. ... Submit 6” (154mm) by 10” (254mm) section of panel for each panel selected indicating the color, texture, and ...


    • [DOC File]This guide spec is intended to be used with “Architectural ...

      https://info.5y1.org/color-ply-laminated-wood_1_9c5dce.html

      An edgeband of 3mm on doors and drawer fronts is more durable, but the thicker edge will be more noticeable if the laminate is a wood grain or other pattern rather than a solid color. Drawers: Sides: [Solid hardwood][Seven- or nine-ply hardwood plywood with no internal voids] [Particle board with melamine surfacing]


    • [DOC File]08 1510 – PLASTIC LAMINATE FACED WOOD DOORS

      https://info.5y1.org/color-ply-laminated-wood_1_d2f1f8.html

      Cross-banding: 1/10 inch (2.5mm) thick 3-ply wood cross-banding. Stiles and Rails: Fire retardant treated structural composite lumber. Stiles, 1-3/8 inches (35mm) before trimming. Rails: Top 1” width. Bottom 2” width. Adhesive: Type I waterproof H.B. Fuller XR2859. Delete the following paragraph if …


    • [DOCX File]SECTION 12 32 00 - MANUFACTURED WOOD CASEWORK

      https://info.5y1.org/color-ply-laminated-wood_1_277532.html

      D. Laminated Glass: Fabricate of two (2) sheets of 3 mm (1/8 inch) thick clear ASTM C1172 Kind LT glass, laminated together with a 1.5 mm (0.060 inch) thick vinyl interlayer, to …


    • [DOCX File]Bid Specification - WBDG | WBDG

      https://info.5y1.org/color-ply-laminated-wood_1_eca8a4.html

      Drawer fronts shall be solid wood, MDF, lumber core, or a minimum three (3) ply balanced laminated construction of minimum forty-five pound (45lbs.) density fiber …


    • [DOC File]SITE WORK - ARE Forum

      https://info.5y1.org/color-ply-laminated-wood_1_16ee74.html

      Plywood. Manufactured wood panel consisting of several thin wood veneer sheets permanently bonded together with the grain of each ply perpendicular to the adjacent. Central ply: core, outer plies: face and back. Odd number of plies for flatness. 4’x8’x5/16” to 1 1/8”. Used as wall and roof sheathing, subflooring, underlayment and formwork.


Nearby & related entries: