Convert gpm to ft s
[DOCX File]University of Georgia
https://info.5y1.org/convert-gpm-to-ft-s_1_8e872c.html
Convert depth and area to volume. Depth of water = 6” = ½ ft. Area = 100 acres. Volume = depth x area = ½ ft x 100 ac = 50 ac-ft. 2. Convert cfs to gpm. gpm (gallons per min) = cfs (ft3/s) x 450. 1 ft3 = 7.5 gal, 1 min = 60 s. 3. Find total discharge from depth, width, velocity measurements. Discharge = Velocity x Area. Avg depth = total ...
[DOC File]Mike Slusher’s Pump Test
https://info.5y1.org/convert-gpm-to-ft-s_1_629e00.html
200 psi 700 1 3/4” 2 x 100 ft 60 psi. 250 psi 500 1 1/2” 1 x 100 ft 58 psi. 750 gpm pump 5 inch suction 20 feet. Pump Pressure GPM Nozzle Tip Discharge Hose Pitot Reading. 150 psi 750 1 3/4” 2 x 100 ft 68. 200 psi 525 1 1/2” 1 x 100 ft 62 psi. 250 psi 375 1 1/4” 1 x 100 ft 66 psi. 500 gpm pump 4 …
[DOC File]SEWAGE FLOW RATE ESTIMATING GUIDE
https://info.5y1.org/convert-gpm-to-ft-s_1_91d943.html
(Range and Typical are shown in gallons per unit) Estimates are based on US standards for water usage and sewage strength. Typical Wastewater Flow Rates from Commercial Sources
[DOC File]FORMULA SHEET - Homestead
https://info.5y1.org/convert-gpm-to-ft-s_1_691754.html
Q = GPM, H = Ft. Head, P = BHP, D = Impeller Diameter, RPM = Pump . Pump Law = (P2/P1) = (GPM2/GPM1)2 Solving for GPM2 = GPM1 x (P2/P1)2 P = (P GPM = Gallons Per Minute AIRSIDE FORMULA SHEET. CFM increases proportionally as RPM increase. SP increases as the square2 of the RPM. BHP increases as the cube3 of the RPM.
[DOC File]FLUID MECHANICS - Auburn University
https://info.5y1.org/convert-gpm-to-ft-s_1_8fe7f3.html
In working with problems with complex or mixed system units, at the start of the problem convert all parameters with units to the base units being used in the problem, e.g. for S.I. problems, convert all parameters to kg, m, & s; for B.G. problems, convert all parameters to slug, ft, & s. Then convert the final answer to the desired final units.
[DOC File]CHE 30101 (Spring 2000)
https://info.5y1.org/convert-gpm-to-ft-s_1_732297.html
The scale model is found to deliver 400 gpm with a head increase of 20 ft. Assuming dynamical similarity, for the full-size pump. 4) Q = 8,533 gpm 5) (h = 569 ft III. A rodlike wire of radius r1= .05 cm is pulled steadily with velocity V = 2.0 cm/s through a horizontal die of …
[DOC File]Omregningsfaktorer fra anglo-amerikanske enheter til SI ...
https://info.5y1.org/convert-gpm-to-ft-s_1_e3e711.html
1000 gpm = 2.228 cfs 0.06309 m3/s. Force lb 4.448 newton (N) Kinematic viscosity ft2/s 0.0929 m2/s = 104 St. Length in 25.4 mm. ft 0.3048 m. mile = 5280 ft 1.609 km. Mass slug 14.59 kg. Power ft(lb/s 1.356 watt (W) = J/s = N(m/s. hp = 550 ft(lb/s 745.7 W
[DOC File]SewerGeek.com - Just another WordPress site
https://info.5y1.org/convert-gpm-to-ft-s_1_fe7754.html
ft3/sec. = ft2 x ft./sec. Convert MGD to ft3/sec. = 1.55 x = ft3/sec. Use the formula, ft3/sec. = ft2 x ft./sec. To get the area; ft2. ft3/sec. = ft2 x ft./sec. ft3/sec. = ft2 x. ft3/sec. ft2 = D2 x .785.785 ft2 . D2. ft2 = 2 = D. D (Diameter) Convert to inches. 12 in./ft. **We are looking …
[DOCX File]rexsunco.com
https://info.5y1.org/convert-gpm-to-ft-s_1_4277bd.html
British_Thermal_Units/hourJoules/secondBritish_Thermal_UnitsJoulesKilojoulesWatts/square inchWatts/square centimeter
[DOC File]Flow in Pipes
https://info.5y1.org/convert-gpm-to-ft-s_1_d4277c.html
where the friction loss is in feet (ft), flow rate is in gallons per minute (gpm), the pipe length is in feet (ft), and the pipe diameter is in inches (in). The friction loss can be converted to pounds per squared inch (psi), by multiplying the value in feet by 0.433
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.