Convert water pressure to gpm
[DOC File]PART I: WELL WATER
https://info.5y1.org/convert-water-pressure-to-gpm_1_5f3675.html
At twelve inches, the gpm would increase to only 2.7 gpm, and the backwash required would jump to 10.6 gpm (the maximum on my pressure tank). My goal was to have a relatively simple, low maintenance system with as few elements as possible, at as little additional cost to convert.
[DOC File]Mike Slusher’s Pump Test
https://info.5y1.org/convert-water-pressure-to-gpm_1_629e00.html
The following formula can be used to convert nozzle pressure to gallons per minute. GPM = 29.83 c d2 (np. C= coefficient of discharge nozzle. D = diameter of nozzle in inches. P = pressure of flow (pitot reading) Example: Diameter of nozzle 2” Nozzle pressure 72 psi. Coefficient of nozzle 0.99. GPM = 29.83 x 0.99 x 2” squared x square root ...
[DOCX File]30/60 isometric diagrams of the drain, vent, water ...
https://info.5y1.org/convert-water-pressure-to-gpm_1_b1713f.html
30/60 isometric diagrams of the drain, vent, water distribution, interior and exterior storm systems. Indicate water supply, drainage fixture units, and storm area drainage with gpm …
[DOC File]Conversion Sheet Page 1 - California State Water Resources ...
https://info.5y1.org/convert-water-pressure-to-gpm_1_974354.html
(Pumping Rate, GPM, x 60 Min/Hr ) Supply, Hrs.= Storage Volume, Gals d ( Flow In, GPM – Flow Out, GPM) x 60 min/hr.) 2,000 lbs/Ton 2,000 lbs/Ton. STATE OF CALIFORNIA. DEPARTMENT OF PUBLIC HEALTH. DRINKING WATER OPERATOR CERTIFICATION PROGRAM
[DOC File]Flow in Pipes
https://info.5y1.org/convert-water-pressure-to-gpm_1_d4277c.html
of water. Applying a pressure of 1 psi to a surface is the same as having a 2.31 ft column of water resting on top of that surface. Thus. 1 foot head = 0.433 psi. 1 psi = 2.31 feet of head. 1 meter head = 0.1 kg/cm2. 1 kg/cm2 = 10 meters of head. The ability to express pressure in terms of head makes it easy to convert from one type of energy ...
[DOC File]FORMULA SHEET - Homestead
https://info.5y1.org/convert-water-pressure-to-gpm_1_691754.html
GPM X PSI X .0007 (this is a 'rule-of-thumb' calculation) How many horsepower are needed to drive a 10 gpm pump at 1750 psi? GPM = 10 PSI = 1750 GPM X PSI X .0007 = 10 X 1750 X .0007 = 12.25 horsepower Pump Output Flow (in Gallons Per Minute) RPM X Pump Displacement / 231
[DOCX File]University of Georgia
https://info.5y1.org/convert-water-pressure-to-gpm_1_8e872c.html
Chapter 12: Hydrologic Statistics and Hydraulics. 1. Convert depth and area to volume. Depth of water = 6” = ½ ft. Area = 100 acres. Volume = depth x area = ½ ft x 100 ac = 50 ac-ft. 2. Convert cfs to gpm
[DOCX File]Section 23 05 93 - TESTING, ADJUSTING, AND BALANCING …
https://info.5y1.org/convert-water-pressure-to-gpm_1_b90ab8.html
Verify impeller size by operating the pump with the discharge valve closed. Read pressure differential across the pump. Convert pressure to head and correct for differences in gage heights. Note the point on manufacturer's pump curve at zero flow and verify that the pump has the intended impeller size. Include information in report.
[DOC File]ME-B41 Lab 3: Flow Measurement
https://info.5y1.org/convert-water-pressure-to-gpm_1_fbd4cd.html
c8. Convert the voltage difference to a pressure difference P. c9. Use Bernoulli’s equation to compute the volumetric flow rate in gallons per minute (gpm). The venturi used in this experiment has an inlet diameter of 1.000 inch and contracts to a diameter of 0.567 inches. Write …
[DOC File]CHE 30101 (Spring 2000)
https://info.5y1.org/convert-water-pressure-to-gpm_1_732297.html
A pressure transducer enables the pressure p2 to be monitored at a radial distance r2. The following data were obtained for r1 = 3 in. and r2 = 30 in: Q (gpm): 100 200. p2 - p1 (psi): 20 50. The pressure in the bed is related to the flow rate by the Ergun equation = a+ b. 1) a (with the proper unit) = 0.06514 psi(in/gpm
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.