Copper tubing specifications and sizes
[DOC File]SECTION 232113 - HYDRONIC PIPING
https://info.5y1.org/copper-tubing-specifications-and-sizes_1_f0496c.html
The valves shall individually discharge through 1/4-inch copper tubing to nearest floor drain, hopper drain, or to the outside, if drain line routing is not shown on the drawings. Use 1/2-inch (13 mm), automatic-type air vent valves only where specifically shown on the drawings; Bailey 241, Armstrong 1 …
[DOC File]Copper Guide Specifications
https://info.5y1.org/copper-tubing-specifications-and-sizes_1_42acc5.html
SPEC WRITER NOTE: Copper tubing is limited to sizes up to DN 100 (NPS 4). A.Refrigerant Piping: For piping up to 100 mm (4 inch) use Copper refrigerant tube, ASTM B280, cleaned, dehydrated and sealed, marked ACR on hard temper straight lengths.
SECTION 232113 - HYDRONIC PIPING
Electroplated copper hanger rods, hangers and accessories may be used with copper tubing. Horizontal piping and tubing shall be supported within 300 mm (12 inches) of each fitting or coupling. Horizontal cast iron piping shall be supported with the following maximum horizontal spacing and minimum hanger rod diameters:
“CC” Threads - Mueller Company Water Products
Copper Tubing: Type “K” or “L,” conforming to ASTM B88. PVC: 4-inch Schedule 40 plastic pipe. FITTINGS. Mechanical joint cast iron conforming to AWWA C110, or push on joints conforming to ANSI A21.11 (AWWA C111 87). Mortar lining is required. Furnish conforming joint accessories for each joint fitting. Design working pressure shall be:
[DOC File]Technical Specification Guide for Steam Tracing and ...
https://info.5y1.org/copper-tubing-specifications-and-sizes_1_36b91a.html
A. Manufacturer: Subject to compliance with these specifications, pipe hanger and support systems shall be as manufactured by Cooper B-Line, Inc. [or engineer approved equal]. 2.02 PIPE HANGERS AND SUPPORTS. A. Hangers. 1. Uninsulated pipes 2 inch and smaller: a. Adjustable steel swivel ring (band type) hanger, B-Line B3170. b.
[DOC File]Specification - Section 15060 - Pipe Hangers and Supports
https://info.5y1.org/copper-tubing-specifications-and-sizes_1_bd9625.html
Slip Test – Conduit, Pipe, or Tubing Through Clamp (Strap) Figure 12 9.1.5 (cont.) Figure 13. The clamp shall be installed into the slot opening of the channel and around a section of conduit, pipe, or tubing of the proper size. The conduit, pipe, or tubing shall be of a length at least equal to the width of the channel.
[DOC File]SECTION 331116 - SITE WATER UTILITY DISTRIBUTION …
https://info.5y1.org/copper-tubing-specifications-and-sizes_1_e142d8.html
astm a179 steel tubing with steel tubing fittings is also acceptable. copper tubing shall not be used on sulfur recovery units or in an environment where h2s will attack the copper. steam tracing shall be in accordance with eng. spec. 54d-3, sect. 3.3 or spec. 54c-15, sect. 13, and as illustrated herein.
[DOCX File]Section 23 23 00 Refrigeration Piping - Veterans Affairs
https://info.5y1.org/copper-tubing-specifications-and-sizes_1_739e3a.html
PIPE CLASS C1: COPPER TUBE AND FITTINGS (TYPE K OR L) Tubing: Copper tubing, hard drawn temper, type K or type L, as specified, ASTM B 88. Soldered joints. Fittings: Wrought copper, socket solder-type joint, ASTM B 88 and ANSI B16.22. Couplings shall be of the staked stop type. Flanges: Socket solder-type joint.
[DOCX File]Section 22 13 00 - FACILITY SANITARY AND VENT PIPING
https://info.5y1.org/copper-tubing-specifications-and-sizes_1_a13d7d.html
Refers to the thickness of the wall. Schedule 40 steel tubing is not as thick as Schedule 80. Schedule 80 Tubing OD is constant, ID is not constant due to variations in thickness of tubing. Steel Type “K” Soft Copper “K” is a wall thickness classification for annealed copper; used as the most common water service tubing (measured by ID).
Applications: Tube, Pipe & Fittings: Copper & Copper Alloy Tube a…
This Guide Specification contains basic information on the standards related to the manufacture of copper and copper alloy copper piping system products and materials, the sizes, tempers and configurations available in accordance with these standards, the most common technologies used in joining the tube/pipe and fittings outlined in the ...
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.