Corrugated flexible stainless steel tubing
[DOC File]SECTION 231126 - FACILITY LIQUEFIED-PETROLEUM GAS …
https://info.5y1.org/corrugated-flexible-stainless-steel-tubing_1_79cec4.html
Corrugated stainless-steel tubing with mechanical fittings having socket or threaded ends to match adjacent piping. Tin-lined tube in first subparagraph below is available in 1/4- to 5/8-inch (6.3- to 15.8-mm) OD and is equivalent to NPS 1/8 to NPS 1/2 (DN 6 to DN 15).
[DOC File]Chapter Comm 20
https://info.5y1.org/corrugated-flexible-stainless-steel-tubing_1_36017c.html
The Gastite® Flexible Gas Piping System has been tested in accordance with the American National Standard for Fuel Gas Systems Using Corrugated Stainless Steel Tubing, ANSI LC1-2005. This standard lists performance requirements for certification of CSST systems for use with all recognized fuel gases, including __________.
[DOCX File]SECTION 231123 - FACILITY NATURAL-GAS PIPING
https://info.5y1.org/corrugated-flexible-stainless-steel-tubing_1_f1eef3.html
CSST: Corrugated stainless-steel tubing with mechanical fittings having socket or threaded ends to match adjacent piping. CSST underground shall be designed for such use. Piping shall consist of Type 300 stainless steel CSST with an integral polyethylene sleeve.
[DOCX File]Section 22 15 00 - GENERAL SERVICE COMPRESSED-AIR …
https://info.5y1.org/corrugated-flexible-stainless-steel-tubing_1_efd4b3.html
Stainlesssteel hose flexible connectors shall be corrugated, stainlesssteel tubing with stainlesssteel wire braid covering and ends welded to inner tubing. The stainlesssteel hose connectors shall be rated at 1380 kPa (200 psig) minimum. The end connections for 50 mm or DN50 (NPS 2 inches) and smaller shall be threaded steel pipe nipple.
[DOCX File]SECTION 22 15 00 - General Service Compressed Air Systems
https://info.5y1.org/corrugated-flexible-stainless-steel-tubing_1_a3139b.html
Stainless steel hose flexible connectors shall be corrugated, stainless steel tubing with stainless steel wire braid covering and ends welded to inner tubing. The stainless steel hose connectors shall be rated at 1380 kPa (200 psig) minimum. The end connections for 50 mm or DN50 (NPS 2 inches) and smaller shall be threaded steel pipe nipple.
[DOC File]Lightning Hazzard Could Affects Millions of Newer Homes ...
https://info.5y1.org/corrugated-flexible-stainless-steel-tubing_1_f61d51.html
For Immediate Release . May 29, 2007 --A Class Action Lawsuit against four manufacturers of a relatively new type of fuel gas tubing has identified the installation of a lightning protection system as a remedy for the fire risk associated with CSST (corrugated stainless steel tubing) gas piping systems.
[DOCX File]RECOMMENDED ENGINEERING SPECIFICATION FOR - Flex Hose
https://info.5y1.org/corrugated-flexible-stainless-steel-tubing_1_e2007f.html
A. Construction to be 2 equal length sections of annular corrugated 321 / 304L stainless steel (bronze for models FLTLU3(8)S close-pitch hose (made in USA) with stainless steel (or bronze for models FLTLU3(8)S over-braid (made in USA) that will absorb or compensate for pipe movements thermally or when used in seismic applications.
[DOCX File]RECOMMENDED ENGINEERING SPECIFICATION FOR - Flex Hose
https://info.5y1.org/corrugated-flexible-stainless-steel-tubing_1_8c3ec1.html
B.The corrugated metal hose, braid(s), and a stainless steel ring-ferrule/band (material gauge not less than .048") must be integrally seal welded using a 100% circumferential, full penetration TIG welds. End fittings shall be selected per application. Fittings must be attached using a 100% circumferential TIG weld.
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.