Ft head to psi
[DOC File]Since pump curves often are in head - feet or meters, its ...
https://info.5y1.org/ft-head-to-psi_1_098209.html
Since pressure gauges often are calibrated in pressure - psi or bar, it may be necessary with a conversion to head - feet or meter, common used in pump curves. Converting pressure in psi to head in feet. h = p 2.31 / SG (3) where. h = head (ft) p = pressure (psi) Converting pressure in bar to head in meter. h = p 10.197 / SG (4) where. h = head ...
[DOCX File]Dr Jorge Ibarra
https://info.5y1.org/ft-head-to-psi_1_3840b0.html
Assume the length is 10 ft and the diameter is 0.20 in. If the pressure at the beginning of the artery (outlet of the heart) is equivalent to 0.70 ft Hg, determine the pressure at the end of the artery when the head is (a) 8 ft above the heart, or (b) 6 ft below the heart. Assume steady flow.
[DOC File]Purpose
https://info.5y1.org/ft-head-to-psi_1_c93706.html
The Farm has a total head requirement of 183 ft for 60 PSI at a total GPM demand of no more than 10 GPM. At 10 GPM, the Grundfos 10-SQE05B-200 pump would be able to produce a max of 215 ft of head as demonstrated in Fig 12. With reference to the proportionality of head to PSI as defined earlier: (215-183) ft = 32 ft; => (32/2.307) ft = 14 PSI
[DOC File]Flow in Pipes
https://info.5y1.org/ft-head-to-psi_1_d4277c.html
head. of water. Applying a pressure of 1 psi to a surface is the same as having a 2.31 ft column of water resting on top of that surface. Thus. 1 foot head = 0.433 psi. 1 psi = 2.31 feet of head. 1 meter head = 0.1 kg/cm2. 1 kg/cm2 = 10 meters of head. The ability to express pressure in terms of head makes it easy to convert from one type of ...
[DOC File]CALCULATION EXAMPLE
https://info.5y1.org/ft-head-to-psi_1_f947d3.html
(psi) SG (p (ft fluid) (HEQ1-S (ft fluid) L2 Filter 1 500 3 0.98 7.07 7.07 Table 10 Suction static head. z1 zS z1-zS (ft fluid) 2803 2802 1 Tank pressure head at the inlet of the system. H1 (ft fluid) 0 Velocity head at the inlet of the system. v1 v21/2g (ft fluid) 0 0 Atmospheric pressure head
[DOC File]FORMULA SHEET - Homestead
https://info.5y1.org/ft-head-to-psi_1_691754.html
PSI = Ft. Head x Specific Gravity Ft Head = (PSI x 2.31 . Specific Gravity. Horse Power = GPM x Ft. Head x Specific Gravity (Water) 3960 x Pump Efficiency Horse Power = Nameplate HP x (Amps Actual ) x (Volts Actual) (Rule of Thumb) (Brake) Amps Rated Volts Rated
[DOC File]GPM/GPH Flow based on PVC Pipe Size
https://info.5y1.org/ft-head-to-psi_1_9f7d37.html
Pressure Flow in GPM through pipe ID in inches PSI 1" 1.25" 1.5" 2" 2.5" 3" 4" 5" 20 26 47 76 161 290 468 997 2895 30 32 58 94 200 360 582 1240 3603 40 38 68 110 234 421 680 1449 4209 50 43 77 124 264 475 767 1635 4748 60 47 85 137 291 524 846 1804 5239 75 53 95 153 329 591 955 2035 5910 100 62 112 180 384 690 1115 2377 6904 125 70 126 203 433 ...
[DOC File]California State University, Northridge
https://info.5y1.org/ft-head-to-psi_1_bf8a60.html
Solving this equation gives h = 1.03 ft. Adding two times this value to the original value of hgage = 2 ft gives the required answer. hgage,new = 4.06 ft 2.46 Determine the change in elevation of the mercury in the left leg of the manometer of Fig. P2.46 (copied at the right) as a result of an increase in pressure of 5 psi in pipe A while the ...
[DOC File]California State University, Northridge
https://info.5y1.org/ft-head-to-psi_1_e9775c.html
The turbine discharge pipe has a 4-ft inside diameter. The static pressure at section (2), 10 ft below the turbine inlet, is 10-in Hg vacuum. If the turbine develops 2500 hp determine the power lost between sections (1) and (2). The energy equation gives the head loss between the inlet, i, …
[DOC File]Conversion Sheet Page 1
https://info.5y1.org/ft-head-to-psi_1_963bc2.html
PRESSURE. PSI = ( Head, ft. ) PSI = Head, ft. x 0. 433 PSI/ft. 2.31ft./psi. lbs Force = (0.785) ( D, ft. )2 x 144 in2/ft2 PSI. CHLORINATION
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.