How to configure port channel: free download. On-line document store on 5y1.org

Cisco Nexus 5000 Series NX-OS Software Configuration Guide - Co…
Configure the port-channel as a dot1q trunk using the interface command . switchport mode trunk. Repeat this command on both switches (DTP may automatically cause the port-channel to trunk with only one end configured but we should try to keep configurations similar on both switches).
interface port channel configuration

[DOC File]down.tendacn.com
https://info.5y1.org/how-to-configure-port-channel_1_7812fd.html
91 = voice channel number . Port ID equals the voice channel number minus the proceeding 9. After making these changes, stop and restart the Unified Messenger server. 7.0 INSTALLING THE INTEGRATION LINK ( Connect the Type 9020039 ICU cable to the ICU card on the MD110.
cisco port channel configuration example

Avaya Support
( Configure the ICU port using the ICFUP command. See Figure 1. Where X=ICU card slot number and Y=the number of digits in the extension number. Figure 1 ( Configure the I/O data link to pass a three-digit port ID number using the VMFUP command. See Figure 2. Figure 2 ( Install software patch number 12198 on Program Unit CMPS12 and ELP6.
port channeling cisco commands

support.avaya.com
configure system port-num-in-proto type-based. configure system security profile admin slot-numbering type-based. admin save. admin equipment reboot-isam without-self-test. LT card Max Speed Configuration. configure system max-lt-link-speed link-speed forty-gb. SNMP configuration. configure system security snmp community public host-address 110 ...
port channel setup cisco

[DOCX File]Home Page – Community College of Rhode Island
https://info.5y1.org/how-to-configure-port-channel_1_e19c65.html
command can be used to configure individual access ports. This command automatically activates access mode, PortFast, and removes all associations of the physical switch port with the port-channel interfaces (if there are any).
interface port channel

[DOCX File]www.ccri.edu
https://info.5y1.org/how-to-configure-port-channel_1_88d720.html
In this lab, you configure Port Aggregation Protocol (PAgP), a Cisco EtherChannel protocol, and Link Aggregation Control Protocol (LACP), an IEEE 802.3X (formerly IEEE 802.1ad) open standard version of EtherChannel.
port channel show commands

1
A communication channel, also known as channel, refers either to a physical transmission medium such as a wire or to a logical connection over a multiplexed medium such as a radio channel. It is used to transfer an information signal, such as a digital bit stream, …
configuring etherchannel cisco

[DOCX File]Home Page – Community College of Rhode Island
https://info.5y1.org/how-to-configure-port-channel_1_79dccb.html
Those are RS-232 hardware ports, whereas the ‘Port’ referred to here is the software port used by the TCP/IP protocol. TELNET IPaddr Port. C:> TELNET 192.146.151.245 1. This will fail, but it will assign a single-use IP address. Configure the Ethernet Communications Option using Telnet. In the example below, provide input where necessary to ...
cisco configure port channel

[DOC File]FBN Network Documentation
https://info.5y1.org/how-to-configure-port-channel_1_8de5a7.html
Configure an EtherChannel with Cisco PAgP. The first EtherChannel created for this lab aggregates interfaces Fa0/11 and Fa0/12 between ALS1 and ALS2. Make sure that you have a trunk link active for those two links with the . show interfaces trunk. command. ALS1# show interfaces trunk. Port Mode Encapsulation Status Native vlan
interface port channel configuration

[DOCX File]Home Page – Community College of Rhode Island
https://info.5y1.org/how-to-configure-port-channel_1_74d52d.html
set port channel 3/1-16 mode off Disable auto-negotiation of EtherChannels on all ports on module 3. (The previous commands to configure the ports on module …
cisco port channel configuration example

How to configure port channel