Lab power supply kit
[DOC File]EE 101 Lab 2 Ohm’s and Kirchhoff’s Circuit Laws
https://info.5y1.org/lab-power-supply-kit_1_b72834.html
Your circuit prototype board, your lab kit (containing resistors, resistor color code chart, potentiometer, and alligator clips), and the bench power supply, multimeter, and banana cables furnished in the lab. Procedures. P1. → Construct the circuit shown in Figure 1 of …
[DOC File]Outline for laboratory template
https://info.5y1.org/lab-power-supply-kit_1_18bba7.html
Lab parts kit. IC, Timer/Oscillator, LM 555. Capacitor, ceramic disc, 0.01μF. Capacitor, ceramic disc, (value to be determined) ... Adjust the PS 503A power supply to 5VDC using the digital multimeter (note: you can turn on/off the output of the power supply by pressing the white . OUTPUT.
[DOCX File]NAND Gate Lab - Computer Action Team
https://info.5y1.org/lab-power-supply-kit_1_d6d33d.html
The quad chip in the lab kit has 4 NAND gates with independent inputs and outputs, plus a common power supply “VCC” and ground. The pinout is shown on the left below. For example, the first NAND gate has two inputs (1A and 1B) connected to pins 1 and 2, and an output (1Y) connected to pin 3, as shown on the right below.
[DOC File]EE 101 Lab 1 Batteries, Power Supplies, and Resistors
https://info.5y1.org/lab-power-supply-kit_1_5d6248.html
P5. → Set the DC Bench supply to produce 8 volts between the red and black terminals of the “A” supply. Use the DMM to monitor the voltage while you adjust the supply knob. Demonstrate for your instructor or lab TA that you can adjust the supply to any specified voltage between 2 volts and 15 volts. Instructor/TA initials 1-2. Rev. 9/4/2010
[DOC File]DCS LAB MANUAL
https://info.5y1.org/lab-power-supply-kit_1_c516b4.html
Trainer kit, power supply. THEORY: Demultiplexer as t he name indicates, it has only data input D with 4 outputs namely Y0,Y1Y2 Y3 It has two data selector inputs namely S0,S1, at which control bits are applied. The data bit is transmitted to the data bit Y0,Y1Y2 Y3 of the output lines.
[DOC File]Physics 125 Lab Equipment List - Western Illinois University
https://info.5y1.org/lab-power-supply-kit_1_cf4081.html
LAB 5: RESISTANCES IN SERIES AND PARALLEL (Feb. 25) DC power supply (built into the lab bench, Hampden) Connecting wires (with banana plugs, on wall rack) DPDT switch (with spade lugs to banana adapters) 2 Digital multimeters (Fluke D810 or equivalent) Resistors (5, 10, 15, 20, 25, and 100 ohm) LAB 6: REFLECTION AND REFRACTION (April 1)
[DOCX File]ECE 101 LAB 1 - Computer Action Team
https://info.5y1.org/lab-power-supply-kit_1_4ddeb3.html
Lab bench DC power supply, multimeter and computer, ECE 101 lab kit with protoboard, wires, cables and assorted resistors (ideally 220, 1k, 2k and 47 kOhm, but actual may vary; remember 1 kOhm = 1000 Ohm) Background: OHM’S LAW. defines the relationship between …
[DOC File]Outline for laboratory template
https://info.5y1.org/lab-power-supply-kit_1_71b7c7.html
Brown jumper wires, 3 (U-shaped wires, found in the parts kit) Lab safety concerns. Do not turn on the power supply until you have rechecked your circuit for correct wiring. Do not allow the test leads connected to the power supply to touch each other
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.