Mixing galvanized and stainless steel
[DOC File]GENERAL
https://info.5y1.org/mixing-galvanized-and-stainless-steel_1_40cb5b.html
MIXING BOX. Provide mixing box with two position, 24 Volt (power open/spring closed) factory mounted, low leakage type motorized dampers to mix outside air makeup with space return air. Dampers shall be of the air-foiled type with metal compressible jamb seals, extruded vinyl blade edge seals and stainless steel sleeve bearings.
[DOC File]PART 1
https://info.5y1.org/mixing-galvanized-and-stainless-steel_1_2b6e4a.html
Jul 08, 2009 · G. Mixing Box: 1. Mixing box or combination filter and mixing box. 2. Damper opposed or parallel multi-airfoil blades for: a. Control of outdoor and recirculated air. b. Prevention of air stratification. 3. Maximum damper leakage rate 20 cfm/sq ft @ 4.0 in wg. 4. Damper bearings or bushings; stainless or nylon. 5. Jamb and blade edge seals.
[DOC File]DIVISION 10.2 - GALVANIZING
https://info.5y1.org/mixing-galvanized-and-stainless-steel_1_6afa45.html
mixing of outside air and return air streams should occur outside the air handler. avoid mixing boxes which almost always result in STRATIFICATION (freeze stat tripping) problems. Mixing Box Section. ... Diffusers shall be made of G90 galvanized steel, stainless steel, or aluminum.
[DOC File]SECTION 22 45 00 – EMERGENCY PLUMBING FIXTURES
https://info.5y1.org/mixing-galvanized-and-stainless-steel_1_141fb5.html
All unit chassis shall be fabricated of heavy gauge galvanized steel panels able to meet 125 hour salt spray test per ASTM B-117. All exterior panels shall be insulated with 1/2" thick fiberglass insulation with a maximum k value of .24 (BTU • in) / (hr • ft2 • °F) and rated for a maximum air velocity of 5000 f.p.m. Insulation must meet ...
[DOCX File]Architecture Engineering and Construction
https://info.5y1.org/mixing-galvanized-and-stainless-steel_1_f775e6.html
Painting ferrous metal (except stainless steel) exposed to view. Painting galvanized ferrous metals exposed to view. Painting interior concrete block exposed to view. Painting gypsum drywall exposed to view. Painting of wood exposed to view, except items which are specified to be painted or finished under other Sections of these specifications.
Stainless Steel in Contact with Galvanized Steel ...
Mixing boxes, filter mixing boxes, and economizers shall have parallel blade, interconnecting dampers. Damper blades shall have parallel bends for stiffness and shall be mechanically fastened to steel rods rotating in brass bushings and mounted in rigid galvanized steel frames.
[DOCX File]SECTION 09 91 00 - PAINTING - Veterans Affairs
https://info.5y1.org/mixing-galvanized-and-stainless-steel_1_84a23c.html
Pipe and Fittings: [Galvanized steel with epoxy safety yellow coating] [Type 304 stainless steel] [Type 316 stainless steel] [chrome-plated red brass]. Specifier: Bowl, dust cover, drench hose, and water tempering items below are available options from Bradley.
SECTION 237311 - CENTRAL STATION AIR HANDLING UNITS …
Perforated square steel tubing breakaway posts certified by the manufacturer for single mounting purposes may be used for the single mounting of stationary work zone signs for signs greater than 10 sf. Three-pound steel U-channel posts shall comply with Subarticle 1094-1(B) and may be galvanized steel or painted green by the post manufacturer.
[DOC File]Guide Specifications
https://info.5y1.org/mixing-galvanized-and-stainless-steel_1_9016ab.html
Steel Cables for Galvanized-Steel Ducts: Galvanized steel complying with ASTM A603. Steel Cables for Stainless Steel Ducts: Stainless steel complying with ASTM A492. Steel Cable End Connections: Galvanized-steel assemblies with brackets, swivel, and bolts designed for duct hanger service; with an automatic-locking and clamping device.
[DOC File]SECTION 233113 - METAL DUCTS
https://info.5y1.org/mixing-galvanized-and-stainless-steel_1_bd41a0.html
MIXING BOX. Provide casing module with two sets of parallel-blade, galvanized-steel dampers mounted on steel shafts supported in stainless steel-bearings. Arrange dampers for mixing of air streams. Provide neoprene blade seals. Damper leakages shall not exceed 7 cfm/sq ft at 1.0 inch wg (35 L/s/m2 at 250 Pa). COILS. General Requirements for ...
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Hot searches
- vector addition worksheet with answers
- west african culture and traditions
- physics questions and answers college
- 1120 designator navy
- icd 10 to cpt crosswalk
- jfk medical center hackensack meridian
- advantages and disadvantages of a debit card
- day you were born print
- opioid crisis in maryland
- 10 tips for saving money