Nylon fittings for plastic tubing
[DOC File]1
https://info.5y1.org/nylon-fittings-for-plastic-tubing_1_afa737.html
Polyester or nylon bristles for latex (i.e., water based paint) and natural bristle for oil-based paint. ... Tape PVC Cement PVC/CPVC Pipe /Fittings Plumber's Putty Hose Clamps Pipe Strapping Copper Tubing & Fittings Brass Fittings Plastic Tubing Pipe Insulation Faucet Covers Delta seats & springs Shut off Valves Supply Lines Ballcocks ...
[DOC File]Specification - Section 15060 - Pipe Hangers and Supports
https://info.5y1.org/nylon-fittings-for-plastic-tubing_1_328766.html
2. For supporting vertical runs use epoxy painted or plastic coated riser clamps, B-Line B3373CT or B3373CTC. 3. For supporting copper tube to strut use epoxy painted pipe straps sized for copper tubing, B-Line B2000 series, or plastic inserted vibration isolation clamps, B-Line BVT series. H. Plastic …
[DOC File]T&B Fittings Liquidtight Fittings
https://info.5y1.org/nylon-fittings-for-plastic-tubing_1_252810.html
M. NEMA FB 1 – Fittings, Cast Metal Boxes, and Conduit Bodies for Conduit, Electrical Metallic Tubing and Cable. N. NFPA 70 – National Electrical Code (NEC). O. UL 94 – Standard for Tests for Flammability of Plastic Materials for Parts in Devices and Appliances. P. UL 467 – Grounding and Bonding Equipment.
[DOC File]Agilent 3000 series Gas Chromatographs Site Preparation ...
https://info.5y1.org/nylon-fittings-for-plastic-tubing_1_f9c57c.html
A long length of tubing will act as a muffler to reduce the noise associated with a vacuum source. This picture shows a leur fitting connected to the sample vent. The fitting has a barb for connecting 1/8-inch OD plastic tubing. This fitting is available as part number G2890-60520, Male Nylon Leur Fitting, 10/pk.
SECTION 230943 - PNEUMATIC CONTROL FOR HVAC SYSTEMS
In mechanical rooms bundled plastic tubing with suitable junction boxes or single plastic tubing with tray or raceway may be used. Conceal tubing. Run exposed only in mechanical rooms, storage rooms and like, in neat manner and properly supported. [Refer to Division 23 Section "Hangers and Supports for HVAC Piping and Equipment".]
[DOCX File]SECTION 33 41 13 - FOUNDATION DRAINAGE
https://info.5y1.org/nylon-fittings-for-plastic-tubing_1_64cde4.html
D273712 - Polyethylene (PE) Plastic Tubing. D303414 - Type PSM Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings. D421613 - Rigid Poly (Vinyl Chloride) (PVC) and Related PVC and Chlorinated Poly (Vinyl Chloride) (CPVC) Building Products Compounds.
[DOC File]Construction Specification 44—Corrugated Polyethylene Tubing
https://info.5y1.org/nylon-fittings-for-plastic-tubing_1_a22e50.html
Unless otherwise specified in section 8 of this specification or shown on the drawings, connections are made with manufactured junctions comparable in strength with the specified tubing. All split fittings shall be securely fastened with nylon cord or plastic zip ties before any backfill is placed.
[DOC File]Construction Specification 44—Corrugated Polyethylene Tubing
https://info.5y1.org/nylon-fittings-for-plastic-tubing_1_6b2a61.html
Unless otherwise specified in section 9 of this specification or shown on the drawings, connections are made with manufactured junctions comparable in strength with the specified tubing. All split fittings shall be securely fastened with nylon cord or plastic zip ties before any backfill is placed.
[DOCX File]SECTION 22 11 00 - FACILITY WATER DISTRIBUTION
https://info.5y1.org/nylon-fittings-for-plastic-tubing_1_39be0d.html
B.Plastic pipe, fittings, and solvent cement shall meet NSF 14 and shall be NSF listed for the service intended. 2.2 UNDERGROUND WATER SERVICE CONNECTIONS TO BUILDINGS A.From inside face of exterior wall to a distance of approximately 1500 mm (5 feet) outside of building and underground inside building, material to be the same for the size ...
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.