Ping a specific port command prompt

    • [PDF File]HL2170W Windows Network Connection Repair Instructions

      https://info.5y1.org/ping-a-specific-port-command-prompt_1_27ce87.html

      3. PING the Brother machine: a. While still in the command prompt window, type: PING xxx.xxx.xxx.xxx (Where xxx.xxx.xxx.xxx is the Brother machine's IP Address noted earlier.) b. Press ENTER on your keyboard. The computer will ping, or try to communicate with the Brother machine. When completed, you will receive the PING STATISTICS. c.

    • [PDF File]Cisco RV320/RV325 Quick Start Guide

      https://info.5y1.org/ping-a-specific-port-command-prompt_1_054639.html

      DMZ—Lit green when the DMZ/WAN port is configured as a DMZ. DIAG—Blinks red when the firmware is updating. Lit red when the device ... STEP 1 Open a command window by using Start > Run and enter cmd. STEP 2 At the Command window prompt, enter ping and the device IP .

    • [PDF File]Sophos XG Firewall Command Reference Guide v16

      https://info.5y1.org/ping-a-specific-port-command-prompt_1_11f70f.html

      Accessing Command Line Console There are two ways to access Sophos XG Firewall CLI: • Connection over Serial Console - Physically connecting one end of a serial cable -RJ45 connector to the Console port of the device and the other end to a PC’s serial port.

    • [PDF File]Command-Line IP Utilities - Guide to TCP/IP

      https://info.5y1.org/ping-a-specific-port-command-prompt_1_1d59ed.html

      The Ping utility executes an end-to-end connectivity test to other devices and obtains the round-trip time between source and destination device. Ping uses the ICMP Echo and Echo Reply packets to test connectivity. Excessive usage may appear to be a denial of service (DoS) attack. Syntax ping [-t] [-a] [-n count] [-l size] [-f] [-i TTL] [-v TOS]

    • [PDF File]INTRODUCTION z/OS Console Commands for TCP/IP cont …

      https://info.5y1.org/ping-a-specific-port-command-prompt_1_5e4111.html

      If you need details about a command, refer to the appropriate documentation. TCP/IP Commands for TSO/E Note: The following TCP/IP commands should be done from the TSO command panel or the READY prompt. Note: hostname may be the IP address of the host, or the host name of the host. • FTP hostname {port} - Connect to remote host to get/put files.

    • Aruba Mobility Controller: Configuration and Deployment Guide

      specific to your system that needs to be entered (xxxxxxxx) Comment about a command or set of commands xxxxxxxx Prompt, system response or other displayed information Via console 1. Using a standard RS-232 cable, connect the mobility controller to the serial port of a terminal or PC. 2.

    • [PDF File]How to use PsPing to test ping, latency & bandwidth ...

      https://info.5y1.org/ping-a-specific-port-command-prompt_1_4662bd.html

      IMP ping tests can be used just to check that a target machine is up and contactable, but T P ping can be used to check whether a service on a port can be communicated with, such as the default Runtime Resource port of 8181. To execute a TCP connect test, specify the port number. The following example executes connect attempts

    • [PDF File]Using the Command-Line Interface - Cisco

      https://info.5y1.org/ping-a-specific-port-command-prompt_1_84c35b.html

      switch prompt. CLI Command Hierarchy ... exit Exit from command interpreter fcping Ping an N-Port fctrace Trace the route for an N-Port. ... and a variety of protocol-specific modes. Configuration mode is the starting point for all configuration commands. The following commands are …

    • [PDF File]DrayTek ADSL Routers

      https://info.5y1.org/ping-a-specific-port-command-prompt_1_94a713.html

      17.IP Ping from Telnet If Pings from a PC to IP Addresses directly on the Internet fail this could be a routing issue between the PC and the Vigor. To test this, Telnet into the Vigor and use the ‘IP Ping’ command to ping the same public IP Address: ip ping 216.239.59.147

    • [PDF File]ArubaOS 5.0 Command Line Interface

      https://info.5y1.org/ping-a-specific-port-command-prompt_1_7a6ef1.html

      ping Send ICMP echo packets to a specified IP address. traceroute Trace route to specified IP address. NOTE There are several other sub- command modes that allow users to configure individual interfaces, subinterfaces, loopback addresses, GRE tunnels and cellular profiles. For details on the prompts and the

Nearby & related entries:

To fulfill the demand for quickly locating and searching documents.

It is intelligent file search solution for home and business.

Literature Lottery

Advertisement
Hot searches

©2024 5y1.org, Inc. All rights reserved.