Pipe sizes and dimensions
[DOCX File]Section 23 50 11 - BOILER PLANT MECHANICAL EQUIPMENT
https://info.5y1.org/pipe-sizes-and-dimensions_1_a94517.html
All other nozzles shall have threaded pipe connections for pipe sizes 50 mm (2 inches) and under, 1035 kPa (150 psig) ASME flanged connections for pipe sizes over 50 mm (2 inches). Nozzle sizes listed below are based on National Board of Boiler and Pressure Vessel Inspectors recommendations.
[DOC File]GPM/GPH Flow based on PVC Pipe Size
https://info.5y1.org/pipe-sizes-and-dimensions_1_9f7d37.html
What might be "high pressure" for 1/2" pipe (600psi) may not be "high pressure" for 2" pipe (280psi). There are just too many variables to consider to give a real world number. The fact of the matter is, on a pressurized system, the pump will dictate the flow and pressure as much as the pipe used. To achieve the flow figures in the peak column ...
[DOC File]Specification - Section 07720 - Dura-Blok Rooftop Support ...
https://info.5y1.org/pipe-sizes-and-dimensions_1_f5a572.html
Base to be 9.6 inches in length or otherwise specified sizes available. Heavier loads, may require CLDP load distribution plate. E. Roller supports– Dura-Blok™ DBR10 Series & DBR Series: DBR10 Series is sized for pipe up to 31/2 inches, with vertical adjustment up to 12 inches.
[DOC File]Sec. 2.3: Steel Water Pipe
https://info.5y1.org/pipe-sizes-and-dimensions_1_d73181.html
ANSI/AWWA C207 Steel Pipe Flanges for Waterworks Service—Sizes 4 In. Through 144 In. (100 mm through 3,600 mm) ANSI/AWWA C208 Dimensions for Fabricated Steel Water Pipe Fittings. ANSI/AWWA C209 Cold-Applied Tape Coatings for the Exterior of Special Sections, Connections, and Fittings for Steel Water Pipe
[DOC File]Certification Procedure for Plastic Pipe
https://info.5y1.org/pipe-sizes-and-dimensions_1_3d03ad.html
4.2 All pipe sizes listed in Department specifications 707.32 and 707.33 will be tested. If PPI does not test the pipe size, have the size tested by a certified laboratory to show the pipe …
[DOCX File]Section 23 10 00 - FACILITY FUEL SYSTEMS
https://info.5y1.org/pipe-sizes-and-dimensions_1_ae4b74.html
Pipe Sizes 50 mm (2 inches) and under: Rated for 1375 kPa (200 psig) water-oil-gas, swing-type, threaded ends, ASTM B62 bronze body. Provide union adjacent to valve. Pipe Sizes 65 mm (21/2 inches) and above: Rated for 1380 kPa (200 psig) water-oil-gas, swing-type, 861 kPa (125 pounds) ASME flanged ends, ASTM A126 class B cast iron body.
[DOC File]Charlotte Pipe
https://info.5y1.org/pipe-sizes-and-dimensions_1_f570ff.html
Comply with requirements in "Piping Schedule" Article for applications of pipe, tube, fitting materials, and joining methods for specific services, service locations, and pipe sizes. HUB-AND-SPIGOT, CAST-IRON SOIL PIPE AND FITTINGS ([Above] [Below] Grade) Pipe and fittings in this article are available in NPS 2 to NPS 15 (DN 50 to DN 375).
[DOCX File]PART 2- PRODUCTS – MATERIALS
https://info.5y1.org/pipe-sizes-and-dimensions_1_30e75e.html
Pipe sizes 2½” through 4” (75mm – 110mm) shall be manufactured to SDR 17.6 dimensions with a pressure rating of 90 psi when measured at 68°F (20°C). Pipe internal surface finish shall be Ra ≤ 39 µin. Pipe shall be manufactured in sizes from ½” through 4” (20mm – 110mm).
SECTION 15076 CML&C STEEL PIPE FOR MANIFOLD AND …
Steel Pipe Cylinders. Steel pipe 18 inches and smaller in diameter shall be API 5L, Grade B; ASTM A 53 (Type E or S), Grade B; ASTM A 106, Grade B; or ASTM A 135, Grade B. See Section 402001 for additional requirements. Mortar Lining and Coating. Pipe 12 through 18 inches having grooved-end joints shall have dimensions as shown in the following ...
[DOC File]SECTION 232113 - HYDRONIC PIPING
https://info.5y1.org/pipe-sizes-and-dimensions_1_f0496c.html
Pipe Sizes 2 Inch or Smaller: Socket-welding fittings, 2000 lb, ASTM A 181, ANSI B16.11. Pipe Sizes 2-1/2 Inch or Larger: Butt-welding fittings, schedule 40, ASTM A 234, ANSI B16.9. Short radius elbows (ANSI B16.28) will be allowed on gas piping systems, but long radius elbows are preferred and shall be used on other piping systems.
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.