Stair railing code
[DOC File]2012 IBC Draft Chapter 10 - International Code Council
https://info.5y1.org/stair-railing-code_1_9aa27d.html
Stair treads and risers shall comply with Sections 1009.7.1 through 1009.7.5.3. 1009.7.1 Dimension reference surfaces. For the purpose of this section, all dimensions are exclusive of carpets, rugs or runners. 1009.7.2 Riser height and tread depth. Stair riser heights shall be 7 inches (178 mm) maximum and 4 inches (102 mm) minimum.
[DOC File]MOON TOWNSHIP DEPARTMENT OF BUILDING REGULATIONS
https://info.5y1.org/stair-railing-code_1_317dc6.html
Stair nose ¾ “ to 1 ½ “ ... Code approved door alarms on doors leading to pool area. Moon Township building inspector for a final inspection on the pool fence enclosure/ barrier and pool. ... Railing post thru bolted with metal angle bracket on top bolt, (see deck guide).
[DOCX File]SECTION 05 51 00 - METAL STAIRS
https://info.5y1.org/stair-railing-code_1_c5b444.html
Provide stair framing capable of withstanding stresses resulting from railing loads in addition to the loads specified above. Limit deflection of treads, platforms, and framing members to L/360 or 6.4 mm (1/4 inch), whichever is less.
SECTION 05521 – ALUMINUM HANDRAIL AND RAILINGS
Handrail will be installed at a height of 34 – 38 inches above ramp surface or stair tread nosings. Handrail will be stainless steel 304, 1.9 “ OD, .062” wall thickness and shall have a continuous surface.
[DOC File]SECTION 055200 - METAL RAILINGS
https://info.5y1.org/stair-railing-code_1_819779.html
For Stair Rails: 6 feet (1800 mm). Secure wall brackets and railing end flanges to building construction as follows: Retain as many of the subparagraphs below as apply to the project. Delete those that do not apply. For concrete and solid masonry anchorage, use drilled-in …
[DOCX File]Beautiful Railing Systems & Contract Metal Manufacturing
https://info.5y1.org/stair-railing-code_1_c0086f.html
Governing code should be checked for specific requirements. Most codes require a 200 pound minimum concentrated load applied in any direction at any point on the top rail. - OR - Railing assembly shall withstand a minimum uniform load of [50] [_____] pounds per foot applied horizontally or vertically downward, but not simultaneously, on the top ...
[DOC File]SECTION 055000 - METAL FABRICATIONS
https://info.5y1.org/stair-railing-code_1_ce604f.html
Coordinate with the work of Section [ ] for the provision of the perforated metal paneling to be used in the stair railing system. For fittings, elbows, wall brackets, and escutcheons provide machined steel. Provide splice connectors of steel as shown. Provide return at free ends of …
SECTION 05521 – ALUMINUM HANDRAIL AND RAILINGS
Handrail will be installed at a height of 34 – 38 inches above ramp surface or stair tread nosings. Handrail will be anodized aluminum 6063 Sch. 40, 1 ½ in IPS nominal (1.90 in. …
SECTION 05521 – ALUMINUM HANDRAIL AND RAILINGS
Provide railing toe plates when adjacent to or above and open to stair system, floor or grade below and in accordance with the following: Size; 4-inch high extruded section. Clearance of Toe Plate Bottom Above Top of Walking Surface: 1/8 inch minimum and 1/4 inch maximum. Notch flanges as required at railing posts and post base plates.
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.