Stand alone damper control thermostat
[DOCX File]General
https://info.5y1.org/stand-alone-damper-control-thermostat_1_30f63a.html
Sep 18, 2014 · Direct Digital Control (DDC) compatible with BACnet or LonWorks. Controlled by an energy management system or programmable thermostat with week day and week end programming and four daily operation modes. Economizer. Required according to ANSI/ASHRAE/IESNA Standard 90.1-2010 and local code requirements. Capable of actuating to 100% of the AHRI ...
[DOC File]SECTION 237339 - INDOOR, DIRECT GAS-FIRED HEATING …
https://info.5y1.org/stand-alone-damper-control-thermostat_1_c697ed.html
Control Devices: Remote Thermostat: Adjustable room thermostat with temperature readout. ... Outside-Air, and Return-Air Damper Control: Outside-air damper shall open (to minimum) when supply fan starts, and close when fan stops. ... Stand-alone control module for packaged unit controls. Coordinated controls and control sequence with Division ...
[DOC File]Engineering Specifications - Viconics
https://info.5y1.org/stand-alone-damper-control-thermostat_1_276978.html
Non-communicating stand-alone as well as communicating BACnet, Echelon and Zigbee wireless models are available depending on the application. Quality Assurance - The thermostat shall be manufactured within a certified . ISO 9001. and . ISO 14001. facility and must have the following industry approvals: All models: UL 873 (US) CSA C22.2 No.24 ...
[DOCX File]Section 23 09 23 - DIRECT-DIGITAL CONTROL SYSTEM FOR …
https://info.5y1.org/stand-alone-damper-control-thermostat_1_4ab74d.html
3.All control functions shall execute within the stand-alone control units. All new controllers installed will also include all software and/or hardware required to program, commission, or alter the sequence of operation of said controller(s). Controllers requiring software or hardware that is not commercially available will not be allowed.
[DOC File]Automatic Temperature Control Specification
https://info.5y1.org/stand-alone-damper-control-thermostat_1_297d88.html
A thermostat locking function shall be available from the system controller with minimum local control at each thermostat in the system. ... Stand Alone System Controller. ... An independent 24VAC/100VA transformer sized at 5 VA per zone damper & thermostat or D-Fuser shall power the GEN II System Controller and all dampers in the system.
[DOC File]Section 23 09 23 - DIRECT-DIGITAL CONTROL SYSTEM FOR …
https://info.5y1.org/stand-alone-damper-control-thermostat_1_a1f15d.html
All control functions shall execute within the stand-alone control units via DDC algorithms. ... Public Space Thermostat: Public space thermostat shall be a platinum sensor and shall not have a visible means of set point adjustment. ... and shall provide complete modulating control of the damper. The motor shall have a closure torque of 35-inch ...
[DOCX File]SPECS FOR LENNOX L Connection SYSTEM
https://info.5y1.org/stand-alone-damper-control-thermostat_1_579b64.html
The module shall be capable of stand-alone operation with either a standard room thermostat or zone sensor without the use of an interface board. The module shall control the stages of heating and cooling as well as directly control the optional economizer via analog output.
[DOC File]Automatic Temperature Control Specification
https://info.5y1.org/stand-alone-damper-control-thermostat_1_2dbcbc.html
PART 8: Stand Alone System Controller. ... When utilizing perimeter electric or hot water baseboard heating for supplemental heating, the thermostat or TAP with Damper Control Board operates a zone damper only for airflow and energizes the supplemental heat when the temperature drops two degrees below set point. At one degree below set point ...
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.