Step down transformer 480 240
[DOC File]Introduction to Distribution Systems
https://info.5y1.org/step-down-transformer-480-240_1_7d4f09.html
120/240 single phase. 120/208 3 phase. 277/480 3 phase. The 120/240 configuration is obtained from the low-side of a HV/240 volt transformer, where HV is the rated voltage on the high voltage side, and the 240 is the rated voltage on the low voltage side.
[DOC File]Home | US Forest Service
https://info.5y1.org/step-down-transformer-480-240_1_05079f.html
Jun 17, 2002 · Fluorescent and other discharge lighting can be used at 277 volts. 480 volt single phase, 480V three phase, and 277 volt single phase loads can be used on this system. Also good for minimizing voltage drops on long runs. Disadvantages are that a step down transformer is required to get 120/208 or 120/240 volt power for lights and outlets.
[DOC File]IEEE Standards - draft standard template
https://info.5y1.org/step-down-transformer-480-240_1_b536d3.html
For single phase system 480/240 or 240/120 . 480/240 volts, three phase, four wire, mid-tap, delta. When using this voltage configuration larger equipment loads such as three-phase transformer fans and oil pumps need to be specified at 480 volts. Other system loads can be specified at either 480 or 240 …
[DOC File]1 - Eaton
https://info.5y1.org/step-down-transformer-480-240_1_dfe8a4.html
This specification covers the electrical and mechanical characteristics of Eaton’s Cooper Power series 45-10,000 kVA Three-Phase Step-Down Pad-Mounted Distribution Transformers. KVA ratings for transformers with secondary voltages not exceeding 700V are 45-3,750 kVA, while kVA ratings for transformers with secondary voltages greater than 700 ...
[DOCX File]ATE1120: Electrical Fundamental-II
https://info.5y1.org/step-down-transformer-480-240_1_7ca118.html
The most common type of control transformer has two primary coils and one secondary coil, as shown in Figure 1.9. Figure 1.9: A Typical Control Transformer Configuration. In most cases, the control transformer is used to reduce the main or line voltage of 240 VAC or 480 VAC to a control voltage of 120 VAC. Notice that the primary windings are ...
[DOC File]Chapter 31
https://info.5y1.org/step-down-transformer-480-240_1_c3d403.html
Es = 480 V. 31-24. A step-down transformer is used to drop an alternating voltage from 10,000 to 500 V. What must be the ratio of secondary turns to primary turns? If the input current is 1.00 A and the transformer is 100 percent efficient, what is the output current? Ratio = 1:20; Is = 20 A. 31-25.
[DOC File]Functional Specification for Single-Phase Pad-Mounted Type ...
https://info.5y1.org/step-down-transformer-480-240_1_476e39.html
240/120 (3-Bushings) 480/240 (3-Bushings) 120 (2-Bushings) 277 (2-Bushings) 120/240 (4-Bushings–Very uncommon for pad-mounted transformers) The applicable secondary voltage shall be specified on the inquiry. When specified on inquiry, the transformer shall be furnished with full capacity high-voltage taps.
[DOC File]WordPress.com
https://info.5y1.org/step-down-transformer-480-240_1_ed7e98.html
Example: A transformer with a 480 volt input, 240 volt output— can have the output connected to a 240 volt source and thereby become the primary or input to the transformer, then the original 480 volt primary winding will become the output or 480 volt secondary. ... It can be designed to “step up” or “step down” voltages and works on ...
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.