Utv shock spring compressor tool

• 2” Lift Kit - SuperATV, LLC

  Spring Spacers SuperATV strongly recommends using a spring compressor when removing Springs. 2” Lift Kit: for John Deere Gator™ 625i/825i/855D Liability Statement SuperATV’s® products are designed to best fit user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty

---

• [PDF File]RZR XP 900 spring/shock installation

  https://info.5y1.org/utv-shock-spring-compressor-tool_1_967c21.html

  over and install the O-ring. Now, install the upper spring, nylon divider with the long side facing the bottom of the shock, then the lower spring. Use the spring compressor and install the lower spring perch and lower adaptor (Fox). Release the spring compressor and thread the pre-load collar down to the pre-load distance listed on the first page.

---

• [PDF File]Tusk Shock Spring Compressor Instructions - Rocky Mountain ATV/MC

  https://info.5y1.org/utv-shock-spring-compressor-tool_1_5580e6.html

  3. Put each compressor on the spring opposite side of each other. 4. Using a wrench in one hand, hold the compressor body over the top hook area (hook next to the hex bolt head). 5. With the other hand, tighten the compressor using a 17mm wrench or a 3/8” ratchet. Do a few turns on each compressor so each compressor compresses the spring ...

---

• Lift Kit: for Can-Am Maverick X3 - SuperATV, LLC

  4x - Spring Spacer SuperATV strongly recommends using a spring compressor when removing Springs. Need help with your installation? www.superatv.com 8:00am - 9:00pm EST M-Th 8:00am - 7:00pm EST Friday 9:00am - 2:00pm EST Saturday sales@superatv.com 1-855-743-3427 Read instructions and view illustrations before beginning. Liability Statement

---

• [PDF File]DaltonPro Clutch kit DBMT 1000-1 - Dalton Industries

  https://info.5y1.org/utv-shock-spring-compressor-tool_1_136c69.html

  Compressor tool for helix bolt removal 1) Change the helix and secondary spring using the Pulley Spring Compressor Tool (part# 529036012) 2) First, remove the stock helix using the compressor tool. Mark the clutch and take note of arrows on both halves and the helix…and position of the roller in the helix for re-assembly.

---

• [PDF File]Level 4 Spring Kit - Shock Therapy

  https://info.5y1.org/utv-shock-spring-compressor-tool_1_3d218c.html

  This is where you need to use your spring compressor to compress the spring package. Install the lower spring retainer and spin the pre load collar tighter to re-establish your pre load on the springs. Pre load should be about 2 1/4” from the billet top cap to the top of the upper spring (or bottom of the pre load nut) on a 2 seat RZR. It

---

• [PDF File]POLARIS XP 1000 2.5 - 3.0 INTERNAL BYPASS OWNERS MANUAL - Fox Factory

  https://info.5y1.org/utv-shock-spring-compressor-tool_1_224422.html

  FOX PODIUM INTERNAL BYPASS SHOCK ABSORBER ON YOUR PARTICULAR UTV. Reference print standards 604-00-300 rev A. ... Metal-to-metal shock travel in inches (measure before spring installation). 2. Main spring rate (lb-in) - marked on spring (see Reading the Spring Rate). 3. Tender spring rate (lb-in) - marked on spring (see Reading the Spring Rate).

---

• [PDF File]HOW TO EPI RZR XP 4 1000 CLUTCH KIT INSTALL

  https://info.5y1.org/utv-shock-spring-compressor-tool_1_aa0d9f.html

  shock out of the way. Once that’s done, unbolt the ... must be done with a spring compressor tool to avoid tearing your fingers off. EPI also sells a universal spring compressor ... (218) 829-6036 and tell them UTV Off-Road sent you! STEP ELEVEN STEP TWELVE UT OFF-RO MZIE 53.

---

• Installation Instructions

  PRO-UTV #E85-40-039-02-22 ... Use a spring compressor to remove the circlip and the spring retainer/dust shield assembly as shown. (See Photos 27, 28 & 29) 14. You can now remove the main spring, slider and ... shock settings that we tested using the spring rates provided in this kit. Photo 45 Photo 41 Photo 44 43 Photo 42

---

• MOTION PRO, INC.3171 Swetzer Road Loomis, CA 95650 INSTRUCTIONS Tel 650 ...

  Motion Pro Shock Spring Compressor P/N 08-0608 I08-0608 01/2020 Warning: Removing and installing the spring on a coilover shock is a very dangerous proce-dure and improper use of this tool could result in great bodily injury or death. This tool should only be used by a qualifi ed mechanic that has expertise and training in servicing coilover

---

• [PDF File]Tools for Changing Springs and Shock Absorbers - Liquid Levers

  https://info.5y1.org/utv-shock-spring-compressor-tool_1_af7ad3.html

  KL-9001 and KL-9002 Telescopic Spring Compressor (Patented, e.g. US-Patent 5,954,314) Suitable for all vehicles with MacPherson Struts and ... recommended to workshops because this tool has an extended travel (stroke) of 305 mm, a maximum distance ... Tools for Changing Springs and Shock Absorbers 1-06

---

• [PDF File]DO NOT, under any circumstances use this tool to compress larger springs.

  https://info.5y1.org/utv-shock-spring-compressor-tool_1_4f2e09.html

  1. Remove the shock absorber from the vehicle. 2. Clean any excessive amount of dirt and grime from the spring. 3. To maximize tool life, lubricate the threads of the center bolt. 4. Position the spring compressor through the shock opening and into the center of the spring. 5. Jaws should be fitted over coils closest to the ends of the spring ...

---

• [PDF File]RACE TECH SHOCK SPRING COMPRESSOR

  https://info.5y1.org/utv-shock-spring-compressor-tool_1_52ea30.html

  4. Insert the toe of the Compressor between the spring coils and insert the shock shaft into the cutout in the tool. Insert the Locking Pin to hold the shaft captive. 5. Depress the Lever Arm and carefully remove the shock clip. 6. Slowly release the Lever Arm and remove the Tool and spring. SPRING INSTALLATION 1. Reverse order of removal.

---

• [PDF File]2.5 PODIUM-X PODIUM RC2 AFTERMARKET SHOCK RZR XP1000 OWNER’S MANUAL

  https://info.5y1.org/utv-shock-spring-compressor-tool_1_9cc7ed.html

  STEP 4 Determine the Spring Correction Factor using the following table: STEP 5 Use the following formula to calculate crossover ring placement: Crossover Ring Placement = Shaft Travel (in.) x Crossover Point x Spring Correction Factor EXAMPLE • A 5.2-inch travel shock with a 225 lb-in main spring and an 800 lb-in tender spring.

---

• [PDF File]#648603 COIL SPRING COMPRESSOR INSTRUCTIONS

  https://info.5y1.org/utv-shock-spring-compressor-tool_1_fb51cc.html

  Before proceeding with spring removal, make sure to first loosen or remove the shock nuts as necessary using the included shock absorber tool set. To do so, use the following procedure: Procedure for removing "Double D" type shock absorber nuts: 1. Place the provided 9/16" hex socket over the hex nut on the shock 2. Fit the proper size oval ...

---

• [PDF File]MX-5 Spring/Shock Installation Front - Racing Beat

  https://info.5y1.org/utv-shock-spring-compressor-tool_1_591c15.html

  5. Disassemble the shock assembly with the aid of a spring compressor tool. If installing lowering springs, remove the bump stop and modify as shown in the photo by cutting and/or grinding. See photo 5. 6. Reassemble the spring assembly, noting the correct parts positioning and orientation as shown in photo 6 & 7. (If installing new shocks, follow

---

• [PDF File]Level 3 Spring Kit - Shock Therapy

  https://info.5y1.org/utv-shock-spring-compressor-tool_1_0d9572.html

  Level 3 Spring Kit XP 1000 2-4 seat Thank you for purchasing the Shock Therapy Level 3 spring kit. This kit will convert the factory front spring system to a true dual rate spring system using our “silent” cross over rings and the addition of new upper coil springs. It will also lengthen the upper rear

---

• [PDF File]67050 - O'Reilly Auto Parts

  https://info.5y1.org/utv-shock-spring-compressor-tool_1_89cfee.html

  Coil Spring Compressor 67050 A. Screw Shaft/Hook Assembly B. Shoe INSTRUCTIONS: AlwAyS weAR SAFeTy glASSeS ANd glOveS. THIS COIl SPRINg COMPReSSOR wIll NOT wORK ON MCPHeReSON STRUT SPRINgS. If the tool is not like what is pictured and/or is missing any of the parts shown, do not attempt to use. 1.

---

• [PDF File]2.5 PODIUM-X AFTERMARKET SHOCK OWNER’S MANUAL - Fox Factory

  https://info.5y1.org/utv-shock-spring-compressor-tool_1_a94a74.html

  Thank you for choosing FOX 2.5 coil-over shock absorbers for your UTV. In doing so, you have chosen the finest suspension products in the world. ... •A 5.2 -inch travel shock with a 375 lbin main spring and an 800in tender spring. •The crossover point is set at 55 percent. •From the table above, the spring correction factor is 0.319. ...

---

Nearby & related entries:

• utv companies looking for dealers
• utv dealers near me
• used utv dealers near me
• utv dealerships near me
• atv utv dealers near me
• utv dealers
• kawasaki utv dealers near me
• used utv for sale by owner