Why not use vlan 1
[DOC File]1 - Hortonville Area School District
https://info.5y1.org/why-not-use-vlan-1_1_6a03d2.html
What is a recommended practice when checking routing problems with the show ip route command? Why is RIP not a good choice in an enterprise network? 9.3.1.3 Packet Tracer Activity 9.3.1.4 Hands on Lab 9.3.2 EIGRP Issues 9.3.2.1 In the scenario, what is …
[DOCX File]Frank Schneemann
https://info.5y1.org/why-not-use-vlan-1_1_012861.html
The default configuration on the switch is to have the management of the switch controlled through VLAN 1. Use the following commands to configure S1 with an IP address. S1 # configure terminal. Enter configuration commands, one per line. End with CNTL/Z. S1(config)# interface . vlan. 1.
[DOCX File]COMP1321 Week 14 CISCO Academy Lab Exercises
https://info.5y1.org/why-not-use-vlan-1_1_9e7525.html
The default configuration on the switch is to have the management of the switch controlled through VLAN 1. However, a best practice for basic switch configuration is to change the management VLAN to a VLAN other than VLAN 1. For management purposes, use VLAN 99. The selection of VLAN 99 is arbitrary and in no way implies that you should always ...
[DOC File]This lab involves using software network analyzers to ...
https://info.5y1.org/why-not-use-vlan-1_1_fde5ad.html
Use the above configuration procedure to configure each of the used switch interfaces for each switch. (Do this on the switch, not on the routers). Once you are done, it is a good idea to download your configuration so you do not lose it. Note: VLAN 1 (one) is used for the management VLAN, so any VLANs created should be numbered 2 to 1000.
[DOC File]Note: This section should be integrated into your study of ...
https://info.5y1.org/why-not-use-vlan-1_1_1c852d.html
Each VLAN needs to have a highly available gateway address in the distribution layer, using the .1 address in the appropriate subnet. The network should be configured such that the Accounting users normally pass over the link between switches C and E, while Engineering users pass over the link between D and E.
[DOCX File]Leaky Bucket Algorithm - Welcome to VLSI
https://info.5y1.org/why-not-use-vlan-1_1_10530d.html
Some VLAN vendors use switch port numbers as a membership characteristic. For example, the administrator can define that stations connecting to ports 1, 2, 3, and 7 belong to VLAN 1; stations connecting to ports 4, 10, and 12 belong to VLAN 2; and so on.
[DOCX File]Weebly
https://info.5y1.org/why-not-use-vlan-1_1_910021.html
Why or why not? It failed because the IPs haven’t been configured for the switches. Configure the Switch Management Interface. Configure S1 and S2 with an IP address. ... interface vlan 1. S1(config-if)# ip address 192.168.1.253 255.255.255.0. S1(config-if)# no shutdown
[DOCX File]www.radford.edu
https://info.5y1.org/why-not-use-vlan-1_1_efb3d4.html
The selection of VLAN 99 is arbitrary and in no way implies that you should always use VLAN 99. First, create the new VLAN 99 on the switch. Then set the IP address of the switch to 192.168.1.2 with a subnet mask of 255.255.255.0 on the internal virtual interface VLAN 99.
[DOCX File]befetrin.files.wordpress.com
https://info.5y1.org/why-not-use-vlan-1_1_3610d0.html
The default 'native VLAN' is VLAN 1, since this one cannot be removed from the switch. Probably the reason VLAN 1 is the 'native VLAN' by default is becuase switches originate frames such CDP, VTP, STP from this VLAN and there is no need to tag them as they are switch-to-switch communication only.
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.