Z shaped aluminum extrusions
[DOCX File]ARCAT spec 10210air 08_90_00air 2020-3-6
https://info.5y1.org/z-shaped-aluminum-extrusions_1_621c05.html
Aluminum Extrusions: ASTM B 221 (ASTM B 221M), alloy 6063-T5 or T-52. Aluminum Sheet: ASTM B 209 (ASTM B 209M), alloy 3003 or 5052 with temper as required for forming, or as otherwise recommended by metal producer for required finish.
[DOC File]SECTION 074210 - Kalin Associates
https://info.5y1.org/z-shaped-aluminum-extrusions_1_666e8e.html
Aluminum Composite Material Panels: Formed with 0.020-inch- (0.50-mm-) thick, aluminum sheet facings. ... Z-Shaped Furring: With slotted or nonslotted web, face flange of 1-1/4 inches wall attachment flange of 7/8 inch, minimum bare metal thickness of 0.0179 inch and depth required to fit insulation thickness indicated. ... perimeter extrusions ...
[DOCX File]SECTION 05 75 30 - CRL-ARCH
https://info.5y1.org/z-shaped-aluminum-extrusions_1_26f522.html
D.Metal Framing Members: Angles, channels, z-clips, hat-shaped and furring channels, provided under Section 05 40 00 - Cold-Formed Metal Framing. [11 gage galv. steel angles, continuous length full height of column. Select size of angle best suited to size of structural column, and diameter of column cover.] ... Aluminum extrusions: ASTM B 221 ...
[DOCX File]SECTION 074219 - METAL PLATE WALL PANELS
https://info.5y1.org/z-shaped-aluminum-extrusions_1_d0b1b4.html
2.2.1 Subgirts: Minimum 16ga. 7/8” hat section, C- or Z-shaped sections, Minimum 16ga. flat strap, minimum 16ga. Nominal thickness. 2.3 MISCELLANEOUS MATERIALS: 2.3.1 Aluminum Extrusions: Alloy and temper recommended by manufacturer for type of use and finish indicated.
[DOCX File]ARCAT | Free Building Product CAD Details, BIM, Specs and …
https://info.5y1.org/z-shaped-aluminum-extrusions_1_61f32e.html
ASTM B 209 - Specification for Aluminum and Aluminum Alloy Sheet and Plate. ASTM C 209 - Standard Test Methods for Cellulosic Fiber Insulating Board. ASTM C 645 - Specification for Nonstructural Steel Framing Members. ASTM C 754 - Specification for Installation of Steel Framing Members to Receive Screw Attached Gypsum Panel Products.
[DOC File]Section 13 34 19 - Metal Building Systems
https://info.5y1.org/z-shaped-aluminum-extrusions_1_6e055b.html
"Z"-shaped, precision-roll-formed, acrylic-coated G30 galvanized steel in different gauges to meet specified loading conditions. 7-inch, 8-1/2-inch, 10-inch, or 11-1/2-inch-deep "Z" sections. ... Windows: Aluminum extrusions (thermally broken) with bronze anodized finish. Horizontal Panel Joint Trim: Extruded aluminum factory painted to match ...
[DOC File]Berner Drive-Thru Air Curtain CSI Specs
https://info.5y1.org/z-shaped-aluminum-extrusions_1_6acab5.html
AIR CURTAINS. Berner Drive-Thru Unit 3 Series (DTU03) air curtains (a.k.a. air doors) are designed to be competitively priced for indoor use on drive-thru windows.They are suitable for openings up to 26 in (66.0 cm) wide in single modules (tandem mount for wider openings), with window heights up to 36 in (91.4 cm) for environmental separation and insect/fume control.
[DOC File]SECTION 07430 - COMPOSITE PANELS (ALUMINUM FACED)
https://info.5y1.org/z-shaped-aluminum-extrusions_1_5496a9.html
Panel Extrusions: Extruded aluminum, ASTM B 221. Concealed Flashings: Formed aluminum sheet, minimum 0.040 inch, ASTM B 209, post-finished to match panels. Stiffeners: formed of extruded aluminum, adhered to interior side of metal wall panel with structural silicone and VHB tape, and designed to tie-in to extrusions.
[DOC File]SECTION 133419 - METAL BUILDING SYSTEMS
https://info.5y1.org/z-shaped-aluminum-extrusions_1_b224f7.html
Girts: C- or Z-shaped sections; fabricated from built-up steel plates, steel sheet, or structural-steel shapes. Form ends of Z-sections with stiffening lips angled 40 to 50 degrees from flange, with minimum 2-1/2-inch- (64-mm-) wide flanges. Retain depths in "Depth" Subparagraph below if manufacturer does not determine depths.
[DOC File]SECTION 07430 - COMPOSITE PANELS (ALUMINUM FACED)
https://info.5y1.org/z-shaped-aluminum-extrusions_1_fec7bd.html
Shop-adhere rolled aluminum horizontal reveal to top of panel and at bottom of base panel. NOW 2580: continuous NOW 3100 system extrusions @ verticals with open horizontal joints at top and bottom, in accordance with the drained/back-ventilated rainscreen method. Intermediate horizontal joints: open or baffled with rolled aluminum reveals.
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.