Alcoa standard aluminum extrusions

    • [DOC File]SECTION 07420 - Advanced Exterior Systems

      https://info.5y1.org/alcoa-standard-aluminum-extrusions_1_68a4a4.html

      Panel Attachment System: Provide aluminum extrusions of 6065 T-5 alloys. Subgirts: When panels are attached to the light gauge metal stud framing substrate the gauge and spacing of these members are to be 18 Gauge in a vertical application (walls) and 16 ga. in a horizontal application (ceilings, soffits, etc.) at 16” O.C. and are to be ...

      alcoa aluminum extrusion profiles


    • [DOCX File]Volare Tension Façade System Specification

      https://info.5y1.org/alcoa-standard-aluminum-extrusions_1_eb45fb.html

      Bunting Architectural Metals: Aria Composite Panel System. 20 River Road, Verona, PA 15147 Main: 412-820-2200 Fax: 412-820-4404 www.buntingarchitecturalmetals.com

      alcoa aluminum extrusion catalog


    • [DOCX File]SPECIFICATIONS FOR A TRIPLE COMBINATION ... - City of …

      https://info.5y1.org/alcoa-standard-aluminum-extrusions_1_6ca922.html

      The rear wall shall be constructed of two (2) 2.00" x 2.00" outer aluminum extrusions and two (2) 2.00" x 1.00" inner aluminum extrusions. All main vertical structural members shall run from the floor to 4.625" x 3.864" x 0.090" thick roof extrusions to provide a cage-like structure with the A-pillar and roof extrusions being welded into a 0.25 ...

      alcoa extrusions inc


    • [DOCX File]Architecture Engineering and Construction

      https://info.5y1.org/alcoa-standard-aluminum-extrusions_1_0e8583.html

      Pressure Caps: Manufacturer's standard aluminum components that mechanically retain glazing. Include snap-on aluminum trim that conceals fasteners. Concealed Flashing: Dead-soft, 0.018-inch (0.457-mm) thick stainless steel, ASTM A 240 of type recommended by manufacturer.

      alcoa extrusion plants


    • [DOC File]SECTION 07430 - COMPOSITE PANELS (ALUMINUM FACED)

      https://info.5y1.org/alcoa-standard-aluminum-extrusions_1_fec7bd.html

      AAMA 2605-05: Voluntary Specification for High Performance Organic Coatings on Architectural Extrusions and Panels. ASTM International (ASTM) ASTM B117: Standard Practice for Operating Salt Spray (Fog) Apparatus. ASTM B221-08 Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes

      alcoa aluminum products


    • [DOC File]DLB-PPC-001

      https://info.5y1.org/alcoa-standard-aluminum-extrusions_1_116ed6.html

      Sep 10, 2013 · 2. Substitutions: Comparable products of other manufacturers will be considered under standard substitution procedures. 2.02 MATERIALS. A. Aluminum Extrusions: ASTM B 221, 6063 alloy, T5 or T52 temper. B. Aluminum Sheet: ASTM B 209, 3003 or 5005 alloy, temper as required for forming or as recommended by metal producer for specified finish.

      alcoa aluminum colors


    • [DOC File]SECTION 08120 - Government of New York

      https://info.5y1.org/alcoa-standard-aluminum-extrusions_1_1ae5b6.html

      7. Thermal Break: Manufacturer's standard continuous thermal barrier. B. Glazed Doors: EDIT SUBPARAGRAPH BELOW FOR WIDER STILES. 1. Fabricate stiles and rails of extruded aluminum tubular shapes, 1/8 inch min wall thickness, not less than 3 inches wide. Attach extrusions together by means of concealed mechanical fasteners and concealed welding. 2.

      alcoa aluminum rims


    • [DOCX File]DLB-PPC-001

      https://info.5y1.org/alcoa-standard-aluminum-extrusions_1_717269.html

      Sep 10, 2013 · a.Dittmer Architectural Aluminum. b.Avadek Walkway Cover Systems. 2.Substitutions: Comparable products of other manufacturers will be considered under standard substitution procedures. 2.02MATERIALS. A.Aluminum Members: Extruded aluminum, ASTM B 221, 6063 alloy, T6 temper. B.Fasteners: Aluminum, 18-8 stainless steel, or 300 series stainless steel.

      alcoa aluminum extrusions


    • [DOC File]SECTION 074210 - Kalin Associates

      https://info.5y1.org/alcoa-standard-aluminum-extrusions_1_666e8e.html

      Aluminum Composite Material Panels: Formed with 0.020-inch- (0.50-mm-) thick, aluminum sheet facings. ... Alcoa Inc.; Reynobond FR. Alpolic Materials, a division of Mitsubishi; Alpolic/pe Alpolic/fr. ... Formed from extruded aluminum. Include manufacturer's standard perimeter extrusions, panel stiffeners, panel clips and anchor channels.

      alcoa aluminum extrusion profiles


Nearby & related entries: