Fabricated rear end housing
[DOC File]I
https://info.5y1.org/fabricated-rear-end-housing_1_2a4651.html
10. Shredder Housing and Frames. Shredder housing and frame shall be predominately fabricated from heavy wall tubing and steel plate. Body end plates shall be a minimum ¾” steel plate. Belt housing covers shall be a minimum ½” steel plate. Drive components shall be compartmentalized for cleanliness, ease of maintenance, safety and greater ...
[DOCX File]2016 4 CYCLINDER RWD RULES
https://info.5y1.org/fabricated-rear-end-housing_1_41c17a.html
4. Cars with fabricated/aftermarket chassis must use stock/factory front strut tower and cross member. a. The front and rear clips must be centered on the middle roll cage section. b. No offset chassis c. All fabricated frame rails must be 1.5x3x0.095 wall minimum. 5. Must have complete six-point roll cage. (see roll cage rules) 6.
[DOCX File]www.fullthrottlemotorspeedway.com
https://info.5y1.org/fabricated-rear-end-housing_1_597961.html
Rod ends (Heim joints) must be steel. Bar length may be adjustable to maintain the rear axle housing centered in the chassis. Bar attachment to be fabricated from steel and mounted with the pivot point on the rear axle tube no further than the inside of the rear spring and not lower than the bottom of …
Lake Ozark Speedway
No weight jack bolts. Rear shocks must be in stock type location (if they came in front of the rear end they must remain there). Rear trailing arms no more than 2 7/8-inches from bottom of housing to center of bolt. Same both sides. Upper control arms no more than 2-inches from housing to center of the bolt.
[DOC File]Tranny mount for five-speed - AirCooledNut
https://info.5y1.org/fabricated-rear-end-housing_1_8d4c63.html
1. Jack up rear end and remove rear tires. 2. Remove the engine and tranny and stock nose cone tranny mount. The stock nose cone mount will not be reused. 3. Put the new tranny on the engine and test fit the assembly in vehicle. Note where nose cone meets the torsion housing.
[DOC File]2019 Mid-East Modified Tour Rules
https://info.5y1.org/fabricated-rear-end-housing_1_4a1499.html
5. Any steel approved OEM passenger car or truck rear end allowed (housing and carrier). OEM rear end must use full or mini spool. Quick change rear end OK. Must use steel axle tubes and 10” ring gear with steel or aluminum spool. Only steel axles allowed. …
[DOCX File]DISCLAIMER
https://info.5y1.org/fabricated-rear-end-housing_1_f93f68.html
Fabricated Steel firewalls allowed with weight penalty. 11.0 FLOOR: ... between to rear frame rails and no lower than the rear axle housing. Cell must be protected with 1”x1” tubing on all sides. ... No cambering of rear ends. May use rear end out of any vehicle, as long as it has SAME pick up points as STOCK frame being used.
Medicine Hat Auto Racing Association
Trunk floor must be removed over rear end housing, entire trunk floor may be removed. All windows must remain open, except opera windows may be covered with clear lexan, no decals. All roof pillars must remain OEM, exception is: ‘B’ pillar may be trimmed to minimum two-inch width and must remain within OEM location.
www.humboldtspeedway.com
Rear clip may be fabricated out of tubing. Front and rear pick-up loop required; otherwise bumpers or other pick-up point will be used. ... May use minimum 23-inch-long pan-hard bar located behind rear end housing or minimum 19-inch-long J-bar mounted to a steel pinion bracket. Measurements are from center of heim joint to center of heim joint.
[DOCX File]lakesidespeedway.net
https://info.5y1.org/fabricated-rear-end-housing_1_58029a.html
1) OEM original type rear end in stock location. 9” rear ends are allowed with stock drum or disc brakes only. All the mounting points must match all mounting points on the rear end being removed. OEM rear end mounts must be level left and right, uppers and lowers. Mounts cannot be more than 3 inches to center of bolt from top of housing.
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.