ࡱ> fheM 0bjbj== "PWW*l1111 "1dR11111111`RbRbRbRbRbRbR$T VR-11111R ?11R ? ? ?1N 11`R ?1`R ? ?"A.KH`R11 h1;M@`RR0R NTW=NW`R ? Boson NetSim LE functionality and supported commands Boson NetSim LE has been specifically designed to support several labs from this book. What that means is that the exact commands required for those labs indeed work, but commands that aren't required for those labs aren't supported in the product. As technology evolves, various technical recommendations provided by the numerous standards committees (and manufacturers that are affected by those modifications), change with the times. This can be observed in interesting ways, all the way down to the Cisco router and Catalyst switch command line interface (or, CLI for short) level. For example, there are several different ways to configure a Cisco router to perform a save of its configuration data: Method #1: The newer (or modern) CLI command, Copy Run Start, performs a save of the Cisco routers configuration data. This CLI command is well documented in modern Cisco courseware, and is the currently recommended method. Method #2: The older (or  legacy ) CLI command,  Write Mem , performs an identical save of the same Cisco router s configuration data. While this CLI command may still work, it is no longer documented in current Cisco courseware, and is no longer recommended. The Boson NetSim"! LE (or Learning Edition) software product, as provided on the CDROM within the CCNA INTRO and CCNA ICND (640-8xxx series) books, simulates only those newer, or more modern, Cisco recommended and documented commands. If you're having difficulty getting asupported lab to work, you might benefit fromreading over the list of commands that Boson NetSim LE supports in each lab.For your convenience, a complete listing of all modern commands that are enabled for completing the included labs (that are documented as enabled in the printed books) are listed below. Also note that Boson NetSim LE doesn't let you make as many mistakes as a real router or switch - for instance, usinga different subnet mask than the lab requires will be rejected byNetSim. The list of commands includes the full syntax of the commands, soyou can compare the commands you're typing to what NetSim is expecting. The list ofcommands are a direct pull of what the software is expecting. INTRO Commands The following 92 commands are supported by the Boson NetSim LE for the labs in the CCNA INTRO Exam Certification Guide. Conf terminal Hostname R1 Interface Serial 0 Ip address 163.1.12.201 255.255.255.128 Interface Serial 1 Ip address 163.1.13.201 255.255.255.128 Interface Ethernet 0 Ip address 163.1.1.201 255.255.255.128 Router rip Network 163.1.0.0 Hostname R2 Ip address 163.1.12.202 255.255.255.128 Encapsulation ppp Ip address 163.1.23.202 255.255.255.128 Ip address 163.1.2.202 255.255.255.128 Hostname R3 Ip address 163.1.13.203 255.255.255.128 Ip address 163.1.23.203 255.255.255.128 Ip address 163.1.3.203 255.255.255.128 Hostname Sw3 Enable secret cisco Line vty 0 15 Password cisco Login Line console 0 Login Password cisco Interface vlan 1 Ip address 163.1.1.213 255.255.255.128 No shutdown Ip default-gateway 163.1.1.201 Interface fastethernet 0/1 Description trunk to SW1 Interface fastethernet 0/2 Description trunk to SW2 Copy running-config startup-config Show ip interface brief Show access-lists Show ip protocol Show running-config Show ip arp Show ip route Trace 163.1.13.203 Ping 163.1.13.203 Ip address 10.1.1.1 255.255.255.0 Enable Disable Show interface serial 0 Show version Show flash Hostname Hannah Write terminal Show config Clock set 16:52:30 31 Dec 2001 Lab 5.pdf Reload in 600 cause I want to Erase nvram Show interfaces status Show version Show flash Hostname Wendell Hostname sw12 Interface fastethernet 0/1 Enable secret cisco Interface vlan 1 Ip address 172.30.101.101 255.255.255.0 Exit Ip default-gateway 172.30.101.1 Lab 6 Write erase Reload Enable password fred Interface Ethernet 0 Ip address 172.30.101.1 255.255.255.0 Interface serial 0 Ip address 172.30.102.1 255.255.255.0 Line vty 0 4 Login Password cisco Interface Ethernet 0 Ip address 172.30.103.2 255.255.255.0 Interface serial 0 Ip address 172.30.102.2 255.255.255.0 Clock rate 56000 Ping 172.30.102.2 Ping 172.30.103.2 Extended pings telnet 172.30.102.2 show users show sessions ip host R2 172.30.102.2 telnet R2 show cdp entry * show cdp neighbor show cdp interface ICND Commands The following 171 commands are supported by the Boson NetSim LE for the labs in the CCNA ICND Exam Certification Guide Lab7.pdf Interface serial 0 Encapsulation frame-relay Ip address 168.11.123.201 255.255.255.192 Frame-relay interface-dlci 502 Frame-relay interface-dlci 503 Interface Ethernet 0 Ip address 168.11.11.101 255.255.255.192 Router igrp 1 Network 168.11.0.0 Ip address 168.11.123.202 255.255.255.192 Frame-relay interface-dlic 501 Frame-relay interface-dlic 503 Ip address 168.11.12.102 255.255.255.192 Ip address 168.11.123.203 255.255.255.192 Frame-relay interface-dlic 501 Frame-relay interface-dlic 502 Ip address 168.11.13.103 255.255.255.192 Ip route 168.11.12.64 255.255.255.192 168.11.123.202 Ip route 168.11.11.64 255.255.255.192 168.11.123.201 Ip route 168.11.13.64 255.255.255.192 168.11.123.203 Ip route 168.11.12.64 255.255.255.192 168.11.123.202 Frame-relay map ip 168.11.123.202 502 broadcast Frame-relay map ip 168.11.123.201 501 broadcast Frame-relay map ip 168.11.123.203 503 broadcast Frame-relay map ip 168.11.123.202 502 broadcast Show ip interface brief Debug ip igrp transactions Show interface Show ip protocol Show frame-relay pvc Show frame-relay map Show frame-relay lmi Interface serial0 Encapsulation frame-relay Interface serial 0.2 point-to-point Ip address 170.1.10.1 255.255.254.0 Frame-relay interface-dlci 302 Ip access-group 102 in Interface serial 0.3 point-to-point Ip address 170.1.12.1 255.255.254.0 Frame-relay interface-dlci 303 Ip access-group 103 in Interface serial 0.4 point-to-point Ip address 170.1.14.1 255.255.254.0 Frame-relay interface-dlci 304 ietf Ip access-group 104 in Interface Ethernet 0 Ip address 170.1.3.1 255.255.254.0 Router igrp 1 Network 170.1.0.0 Access-list 102 permit tcp any host 170.1.2.11 eq ftp Access-list 102 permit tcp any host 170.1.2.11 eq www Access-list 102 permit tcp any host 170.1.2.12 eq ftp Access-list 102 permit tcp any host 170.1.2.12 eq www Access-list 102 deny ip any host 170.1.2.11 Access-list 102 deny ip any host 170.1.2.12 Access-list 102 deny ip 170.1.4.0 0.0.1.255 170.1.6.0 0.0.1.255 Access-list 102 permit ip any any Access-list 103 permit tcp any host 170.1.2.11 eq ftp Access-list 103 permit tcp any host 170.1.2.11 eq www Access-list 103 permit tcp any host 170.1.2.12 eq ftp Access-list 103 permit tcp any host 170.1.2.12 eq www Access-list 103 deny ip any host 170.1.2.11 Access-list 103 deny ip any host 170.1.2.12 Access-list 103 deny ip 170.1.6.0 0.0.1.255 170.1.4.0 0.0.1.255 Access-list 103 permit ip any any Access-list 104 permit tcp any host 170.1.2.11 eq ftp Access-list 104 permit tcp any host 170.1.2.11 eq www Access-list 104 permit tcp any host 170.1.2.12 eq ftp Access-list 104 permit tcp any host 170.1.2.12 eq www Access-list 104 deny ip any host 170.1.2.11 Access-list 104 deny ip any host 170.1.2.12 Access-list 104 permit ip any any Interface serial 0 Encapsulation frame-relay Interface serial 0.1 point-to-point Ip address 170.1.10.2 255.255.254.0 Frame-relay interface-dlci 301 Interface Ethernet 0 Ip address 170.1.5.2 255.255.254.0 Router igrp 1 Network 170.1.0.0 Interface serial 0 Encapsulation frame-relay Interface serial 0.1 point-to-point Ip address 170.1.12.3 255.255.254.0 Frame-relay interface-dlci 301 Interface Ethernet 0 Ip address 170.1.7.3 255.255.254.0 Router igrp 1 Network 170.1.0.0 Interface serial 0 Encapsulation frame-relay ietf Interface serial 0.1 point-to-point Ip address 170.1.14.4 255.255.254.0 Frame-relay interface-dlci 301 Interface Ethernet 0 Ip address 170.1.9.4 255.255.254.0 Router igrp 1 Network 170.1.0.0 Show frame-relay map Show cdp neighbor detail Lab 18 Ip route 172.30.103.0 255.255.255.0 serial 0 Ip route 172.30.101.0 255.255.255.0 172.30.102.1 Router rip Network 172.30.0.0 Router igrp 1 Network 172.30.0.0 Debug ip igrp events Debug ip igrp transactions Debug ip rip events No debug all Lab 19 Ip http server Access-list 101 permit icmp any 172.30.103.0 0.0.0.255 Access-list 101 deny tcp any host 172.30.103.2 eq telnet Access-list 101 permit tcp any 172.30.103.0 0.0.0.255 eq telnet Access-list 101 permit tcp any 172.30.103.0 0.0.0.255 eq www Access-list 101 permit tcp any host 172.30.102.2 Interface serial 0 Ip access-group in Ip access-list extended fred Permit icmp any 172.30.103.0 0.0.0.255 Deny tcp any host 172.30.103.2 eq telnet Permit tcp any 172.30.103.0 0.0.0.255 eq www Permit tcp any host 172.30.102.2 eq telnet Ip access-group fred in No ip access-group fred in Access-list 101 permit icmp 172.30.103.0 0.0.0.255 any Access-list 101 deny tcp host 172.30.103.2 eq telnet any Access-list 101 permit tcp 172.30.103.0 0.0.0.255 eq telnet any Access-list 101 permit tcp 172.30.103.0 0.0.0.255 eq www any Access-list 101 permit tcp 172.30.102.2 eq telnet any Interface serial 0 Ip access-group 101 in Write mem Lab 20 Debug ppp negotiation Interface serial 1 Ip address 172.30.104.2 255.255.255.0 No frame-relay inverse-arp Clear frame-relay inarp Frame-relay map ip 172.30.104.2 202 broadcast Frame-relay map ip 172.30.104.1 201 broadcast Encapsulation hdlc No ip address Interface serial 1.1 point-to-point Ip address 172.30.104.1 255.255.255.0 Frame-relay interface-dlci 202 Interface serial 1.1 point-to-point Ip address 172.30.104.2 255.255.255.0 Frame-relay interface-dlci 201 Encapsulation frame-relay ietf Lab 21 Vlan database Vlan 2 name barney-2 Vlan 3 name Wilma-3 Interface fastethernet 0/5 Switchport mode access Switcport access vlan 2 Interface fastethernet 0/6 Interface fastethernet 0/7 Interface fastethernet 0/8 Interface fastethernet 0/9 12 Interface fastethernet 0/12 Switchport mode dynamic desirable Vlan database Vtp domain fred Show vtp status Show interfaces fastethernet 0/12 switchport Show interfaces fastethernet 0/12 trunk Difference between CCNA 2.0 material and the new ICND/INTRO material One big difference is the inclusion of the 2950 switches these switches still run on the Cisco IOS but the command line syntax is a little different. For example on the 1912 Catalyst to configure a vlan you would use the following set of commands: Switch>enable Switch#config t Switch(config)#vlan 12 name cisco On the new Catalyst 2950 switches the command structure is a little different. Now you type: Switch>enable Switch#vlan database Switch(vlan)#vlan 12 name cisco Notice there is a completely new mode most of you are not familiar with. This mode is the vlan database mode denoted by the (vlan) brackets. This is just one example of the new material included with the new version of the CCNA ICND/INTRO exam. 679 : bc--05 CJOJQJ5CJOJQJ6712 9 : 0cdr~ 0;MY>er30Kd $7Ikrz)@MXiw 3Hn=N`rs  .CClzHgNC[v%%Ih!EiDzHjk C o o 4!j!!!"."P"Q"d"~"""""#+#=#>#Q#k##### $ $$+$,$?$^$$$$$$ %%2%K%L%S%T%%%%%%%&!&5&B&C&J&J&Y&&& 'G'x''''' (8(c({((()F))))))))) **E*E*`*x*****+?+^+++++++++,&,A,X,p,,,,,, -.-.->-N-{-------.../&/'/(///////00 1h/ =!"#$%l i4`4 NormalPJ_HmH sH tH <A`< Default Paragraph Font2o2 BookTitle5CJ,o, Bodyx CJOJQJ8o8 Chap Num5CJOJQJ<o"< Chap-Title5CJOJQJ*o2* Section50oB0 Sectionsub56oR6 SectionsubsubCJ*ob* SubParaCJ(or( Bullet  & F0o0 BulletBody h^h>o> BulletIndent & F >JoJ BulletIndentBody h8^.o. UnNumList ^6o6 UnNumListLast ^(o( CmdEnv>*CJ4o4 CmdEnvLast>*CJ$o$ Note h^h"o" Tip h^h*o* Warning !h^h,o", NoteBody "h^h,o2, NoteLast #h^h0oB0 NoteBullet $ & F8oR8 NoteBulletBody % & F4ob4 WarningFirst &h^h,or, TipFirst 'h^h>o> NoteFirst(hx^h CJOJQJ8o8 NoteCmdEnv )^>*CJ@o@ NoteCmdEnvLast *^>*CJ6o6 SideBarFirst+$a$62o2 SideBarBody ,h^h2o2 SideBarLast -h^h,o, TableTitle.6.o. CellHeading/5$o$ CellBody02o2 TableFootnote1CJ2o"2 FigureCaption26o2 PD356(oB( Footnote4CJ4oR4 ExampleFirst56CJ*ob* Example6>*CJ2or2 ExampleLast7>*CJ.o. BulletChk 8 & F:o: BulletIndentChk 9 & F2o2 Quotation :h^hCJ6o6 BulletQuotation;CJ:o: BulletBodyQuo <^CJ2o2 BulletQuo = & FCJ.o. Stepsub2+ > & F0o0 OpenerList ?^0o0 NumList1 @ & F2o2 NumList2+ A & F >o"> NumListBodyB h^>o2> NumListCmdEnv C^>*CJFoBF NumListCmdEnvLast D^>*CJ&oR& Step1 E & F (ob( Step2+ F & F BorB StepExampleG & F^>*CJBoB StepExampleLast H^>*CJ@o@ StepBulletI & F ^`8o8 StepBulletBody J^,o, Stepsub1 K & F ,o, SubParasubLCJ*o* Caution Mh^h2o2 CautionLast Nh^h.o. Timesaver Oh^h6o6 TimesaverLast Ph^h0o0 NoteIndent Q^4o"4 NoteNumList1 R & F6o26 NoteNumList2+ S & FoB Section Heading=T ,p@ P !$`'h`5B*CJ$OJQJph4oaR4 ExampleBoxedTextU,ob, StepBody V 8@`or` QQFW$d%d&d'dNOPQ5,`, Header X !$o$ FAQHY5CJ o FAQQZ5 o FAQA[52o2 NumListABC1 \ & F&o1& AlphaHead]*o* GlossTerm^5$o$ GlossDef_4o4 NumListABC2+ ` & F"o!" LabBodya*o1"* LabBodyLastb(oq2( LabSubheadc0oB0 SideBarSectiond<o!R< SideBarFigureCaptione.oqb. SideBarBulletf.or. SideBarCmdEnvg6o6 SideBarCmdEnvLasth6oA6 SideBarSectionSubi2o2 SideBarNumList1j4o4 SideBarNumList2+k*P 67129:c d r ~ 0 ; M Y  > e r   0 K d   $ 7 I k r z )@MXiw 3Hn=N`rs  .ClzHgNC[v%Ih!EiDzHjk Co4j.PQd~+=>Qk +,?^ 2KLST ! 5 B C J Y !G!x!!!!! "8"c"{"""#F######### $$E$`$x$$$$$%?%^%%%%%%%%%&&&A&X&p&&&&&& '.'>'N'{'''''''((()&)')()))))))**00000000000000000000000000000000300000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000C%o $J&E*.-0 !"#$%&'0 =C"%_eOUou & Y [   > @   : F n z        I K #(.2HJNT %)CEsw ^b}NP#%HJacdh%'_chj!#[_dhik %(=?[^su_afi$'<>XZ-/KNceEGLO$(Y]7:TV  J L p t !!!!$!@!B!^!a!!!!!!!""""1"3"?"B"Y"["s"w"""""""""# #8#:#]#`#x#z#########\$_$r$w$$$U%Y%%%%%%%%&&&0&<&A&K&X&a&i&m&z&&&&&&&&&&&' '$'.'1'9'='C'F'^'j'p'z'''''((() )))) )%)))))))))%*)*H*L**ia   .2$ X^>Ds!!s"w"""""##V#\### %%s%%9'=''') )))*3333333333333333333333333333333333333356672&b c c   qrss  LLC C F G ##'''''')*UBARTBRKD:\Pearson 2003\Practice Tests\Boson CCNA\free netsim ccna lab commands.docUBARTBRQD:\Pearson 2003\Practice Tests\Boson CCNA\free netsim ccna lab commands final.docUBARTBRQD:\Pearson 2003\Practice Tests\Boson CCNA\free netsim ccna lab commands final.doc|߮o}r~Tp$p|fyH4 TphT@ZVZL# cvKA_r4v%2LR5l`H|9kVR4>#<^"tIRF4PFp8NP*dRX2@OVR\WY;9vb\v=!F`ؼS/a$&SfeNlK_:rDiI^`.^`.88^8`.^`. ^`OJQJo( ^`OJQJo( 88^8`OJQJo( ^`OJQJo(hh^h`. hh^h`OJQJo(^`B*OJQJo(hh^h`B*OJQJo(X8^`XStep .0^`0.hh^h`B*OJQJo(XPX^X`P.88^8`.hh^h`B*OJQJo(X8^`XStep .hh^h`CJOJQJo(qXPX^X`P.0^`0o(.XPX^X`P. ^`OJQJo(^`B*OJQJo(88^8`.XPX^X`P.XPX^X`P.^`B*OJQJo(4>#<Lj3tI_:rSfeNP/aH|9!F`~}|OVdR@''''(*@@UnknownGTimes New Roman5Symbol3& ArialE1Courier (PCL6)G MS Mincho-3 fgO1CourierCourier New;Wingdings"qȈh*&*&/A#K)#J!20dK+G)*2QHX5D:\Pearson 2003\Editorial\Author Kits\Cistm032103.dotBoson NetSim supported commandsBoson Software, Inc.UBARTBROh+'0 (4 P \ ht| Boson NetSim supported commandsosoBoson Software, Inc.d cosooso Cistm032103UBARTBR3ARMicrosoft Word 9.0.@ @.S@/A#՜.+,0 hp  Boson Software, Inc.pKK+  Boson NetSim supported commands Title  !"#$%&'(*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTVWXYZ[\^_`abcdgRoot Entry F0i1Table)WWordDocument"PSummaryInformation(UDocumentSummaryInformation8]CompObjjObjectPool00  FMicrosoft Word Document MSWordDocWord.Document.89q