ࡱ>  usq#`!bjbjmm eDDDX22283tt3XE89L@:@:@:c”6j.LZ$h :DTbb"b"TbTb:@:@:(VVVTb6V@:ЁR@:ZVTbZVVf2J""f@:7 12~N <EbJf6&D I6RVHX$]0III::dIIIETbTbTbTbX$|`\X|`\XXX  Space engineering  SUBJECT \* MERGEFORMAT Structural materials handbook - Part 8: Glossary Foreword This Handbook is one document of the series of ECSS Documents intended to be used as supporting material for ECSS Standards in space projects and applications. ECSS is a cooperative effort of the European Space Agency, national space agencies and European industry associations for the purpose of developing and maintaining common standards. This handbook has been prepared by the ECSS-E-HB-32-30 Working Group, reviewed by the ECSS Executive Secretariat and approved by the ECSS Technical Authority. Disclaimer ECSS does not provide any warranty whatsoever, whether expressed, implied, or statutory, including, but not limited to, any warranty of merchantability or fitness for a particular purpose or any warranty that the contents of the item are error-free. In no respect shall ECSS incur any liability for any damages, including, but not limited to, direct, indirect, special, or consequential damages arising out of, resulting from, or in any way connected to the use of this document, whether or not based upon warranty, business agreement, tort, or otherwise; whether or not injury was sustained by persons or property or otherwise; and whether or not loss was sustained from, or arose out of, the results of, the item, or any services that may be provided by ECSS. Published by: ESA Requirements and Standards Division ESTEC, P.O. Box 299, 2200 AG Noordwijk The Netherlands Copyright: 2011 by the European Space Agency for the members of ECSS Change log  DOCPROPERTY "ECSS ID" \* MERGEFORMAT ECSS-E-HB-32-20 Part 8A  DOCPROPERTY "ECSS Date" \* MERGEFORMAT 20 March 2011First issue  Table of contents  TOC \h \z \t "Heading 1;1;Heading 0;1"  HYPERLINK \l "_Toc289673331" Change log  PAGEREF _Toc289673331 \h 3  HYPERLINK \l "_Toc289673332" Introduction  PAGEREF _Toc289673332 \h 5  HYPERLINK \l "_Toc289673333" 1 Glossary  PAGEREF _Toc289673333 \h 6  HYPERLINK \l "_Toc289673334" 2 References  PAGEREF _Toc289673334 \h 118 Introduction The Structural materials handbook, ECSS-E-HB-32-20, is published in 8 Parts. A glossary of terms, definitions and abbreviated terms for these handbooks is contained in Part 8. The parts are as follows: Part 1Overview and material properties and applications Clauses 1 - 9Part 2Design calculation methods and general design aspectsClauses 10 - 22Part 3Load transfer and design of joints and design of structuresClauses 23 - 32Part 4Integrity control, verification guidelines and manufacturingClauses 33 - 45Part 5New advanced materials, advanced metallic materials, general design aspects and load transfer and design of jointsClauses 46 - 63Part 6Fracture and material modelling, case studies and design and integrity control and inspectionClauses 64 - 81Part 7Thermal and environmental integrity, manufacturing aspects, in-orbit and health monitoring, soft materials, hybrid materials and nanotechnoligiesClauses 82 - 107Part 8Glossary Glossary A A Aluminium Association, USA A-BASIS DESIGN ALLOWABLE A value which at least 99% of the population of values is expected to fall with a confidence of 95%, Ref. [9]; also known as A value and A basis. A-SCAN A single point signal describing the ultrasonic response of material immediately beneath the transducer A-stage An early stage in the polymerisation reaction of certain thermo-setting resins (especially phenolic) in which the material, after application to the reinforcement, is still soluble in some liquids and is fusible; sometimes called resole. [See also: B STAGE, C STAGE] 'A' value An 'A' value is one above which at least 99% of the population of values is expected to fall with a confidence of 95%. [See also: ALLOWABLES] ABLATIVE Sacrificial material which protects a structure from high-velocity, high-temperature gas streams. It is typically used on leading surfaces for planetary re-entry to protect against frictional atmospheric heating. The surface of the ablative is consumed by reaction, abrasion and evaporation or sublimation and the lost material carries heat away from the underlying structure AblaDor DO-31-F Lightweight phenolic ablative ABM Apogee Boost Motor ABS 1 Alumino-boro-silicate ceramic 2 Acrylonitrile-butadiene-styrene copolymer ACC Advanced Carbon-Carbon (NASA) replaced RCC ACCELERATOR A material mixed with a catalysed resin to increase the rate of chemical reaction between the catalyst and resin, used in polymerising resins, also known as promoter or curing agent ACCELEROMETER A device for measuring acceleration, often used in vibration analysis ACCEPTANCE Verification phase with the objective to demonstrate that the flight items are free of workmanship defects and integration errors and ready for operational use, Ref. [1] ACESA Advanced composites with embedded sensors and actuator. An American smart technology programme. ACG Advanced Composites Group, UK ACK analysis Aveston-Cooper-Kelly analysis for modelling the onset of matrix cracking in composite materials (with particular regard to CMC ceramic matrix composites) ACOUSTIC EMISSION (AE) An inspection technique where the sound generated by damage formation and propagation (under test stressing or in-service) is monitored using sensitive, high-frequency microphones. Triangulation techniques can be used to locate the damage events within a three dimensional structure. Frequently used to measure the integrity of composite laminates ACRV Assured Crew Return Vehicle (NASA/ESA) for emergency return of astronauts from orbiting space stations to earth ACS Attitude Control System ACTEX Advanced control technology experiment. An American smart technology programme. ACTIVE COMPENSATION A device able to change its characteristics in response to an externally triggered signal, e.g. stiffness in response to vibration ACUSIL I An ablative foam composed of silicone resin, quartz microballoons, phenolic microballoons and quartz fibre ACUSIL II Lower density ablative foam composed of silicone resin, quartz microballoons, phenolic microballoons and quartz fibre. Remains RF transparent during re-entry ADHEREND Plate adhesively bonded to another plate, Ref. [10]. ADHESION The state in which two surfaces are held together at an interface by forces or the interlocking action of an adhesive or both ADHESIVE A substance capable of holding two surfaces together ADVANCED COMPOSITES Composite materials with structural properties comparable to or better than those of aluminium; e.g. boron, graphite and aramid composites AE See: Acoustic Emission AECMA Association Europen des Constructeurs Matriel Arospatiale; European Association of Aerospace Industries AEFIS Acoustic emission flight instrumentation system. A structural health monitoring system, developed by Boeing. Aerotiss 2.5D Aerospatiale reinforced carbon-carbon (RCC) material with multidirectional fibre architecture Af Austenite finish temperature AFNOR Association Franais de Normalisation; French national standards organisation AFRSI Advanced Flexible Reusable Surface Insulation (Shuttle orbiter) AFWAL Air Force Wright Aeronautical Laboratory, USA AGC Attitude Gain Control AGE HARDENING A thermal treatment used to improve the strength of some metal alloys, e.g. certain aluminium alloys, [See also: Precipitation Hardening]. AGED STRUCTURE A structure which can have structural degradation or damage as a result of being exposed to the combined effects of the environment AGEING General: The process or the effect on materials of exposure to an environment (elevated temperature, ultraviolet radiation, moisture or other hostile environment) for a period of time; also known as aging 1 Material or sample: usually undertaken before testing and applied to simulate the expected service environmental conditions, e.g. exposure to heat and humidity 2 Structure: the progressive change in characteristics owing to exposure to the service conditions, e.g. corrosion, outgassing 3 Processing: a thermal process used to obtain the desired microstructure and properties of metal alloys, e.g. some aluminium alloys AGGRESSIVE ENVIRONMENT Any combination of liquid or gaseous media and temperature that alters static or fatigue crack-growth characteristics from normal behaviour associated with an ambient temperature and laboratory air environment, Ref. [5] AGING [See: Ageing]. AI Artificial intelligence AIAA American Institute of Astronautics and Aeronautics, USA AISI American Iron and Steel Institute AIT Assembly, Integration and Test AIV Assembly, Integration and Verification AKM Apogee Kick Motor ALFLEX Automatic Landing Experimental Vehicle Al-Li Aluminium-lithium alloy ALLOTROPY Existence of a chemical element in two or more physical forms, e.g. carbon as graphite or diamond ALLOWABLE LOAD The load that induces the allowable stress in a material, Ref. [5] ALLOWABLE STRESS The maximum stress that can be permitted in a material for a given operating environment to prevent rupture, collapse, detrimental deformation or unacceptable crack growth, Ref. [5] ALLOWABLES Material values that are determined from test data at the laminate or lamina level on a probability basis (e.g. 'A' or 'B' values), following ASTM or other test standards accepted by the final customer. [See also: A-BASIS DESIGN ALLOWABLE; B-BASIS DESIGN ALLOWABLE; 'A' VALUE, 'B' VALUE] ALLOY Mixture of a base metallic element with one or more other metallic or non-metallic elements AlN Aluminium nitride ALS051 Medium-density, silicone-based ablative ALSCAP Alternative Low-cost, Short Manufacturing Cycle Assessment Programme ALUMINA Aluminium Oxide, Al2O3. ALUMINIDE Intermetallic compound of another metallic element, or elements, with aluminium, e.g. NiAl, TiAl or FeAl ALUMINIUM (Al) Metallic element, melting point 660C, density 2700 kg m-3. Uses: ubiquitous aerospace alloy base, important component in oxidation resistant alloys and coatings and as part of basic strengthening mechanism for nickel-based superalloys ALUMINIUM-LITHIUM An aluminium alloy containing typically between 1% and 3% Li, with the objective of increasing mechanical properties over base alloy alone. Note: Because Li is a low-level alloy addition, Al-Li alloys are classified within the 2XXX, 7XXX and 8XXX wrought alloy designations, plus 2XX casting alloys ALUMINIUM NITRIDE (AlN) Ceramic with high thermal conductivity (140 W/mK to 177 W/mK), but is effectively an electrical insulator (volume resistivity 1010 ohm cm). Can suffer surface oxidation above 700C, density 3320 kg m-3. ALUMINO-SILICATE Compound of aluminium and silicon oxides used in ceramics and some types of glasses for composite matrix materials AMBIENT 1 The surrounding environmental conditions, e.g. pressure, temperature or relative humidity 2 usual work place temperature and humidity environmental conditions, e.g. room temperature ANALYSIS A verification method performing theoretical or empirical analysis by accepted analytical methods. The selected techniques can typically include systematics, statistics, qualitative design analysis, modelling and computer simulation, Ref. [1] ANALYSIS PROCEDURE This document lists all the requirements to be verified by Analysis, grouping them in categories detailing the Verification Plan activity sheets, with planning of the execution and a definition of the associated procedures, Ref. [1] ANALYSIS REPORT A document that describes, for each analysis, assumptions, utilised methods, software and results and contains proper evidence that the relevant requirements are satisfied, Ref.[1] ANALYTICAL LIFE Life evaluated analytically, i.e. by crack-growth analysis or fatigue analysis, Ref. [5] ANALYTICAL MODEL A representation of an item based on mathematical modelling. The modelling is performed on the basis of known mathematical techniques, providing a representation of the item features under investigation, Ref. [1] ANGLE INTERLOCKED A triaxial fabric in which all reinforcement fibres are woven at the same time; also known as integrally woven ANGLE-PLY LAMINATE Possessing equal plies with positive and negative angles. This bidirectional laminate is simple because it is orthotropic ANISOTROPIC Having mechanical or physical properties which vary in direction relative to natural reference axes in the material ANNEALING A heat treatment process: 1 Metals: used to reduce residual stresses. 2 Composites: ineffective at reducing residual stresses ANOXIC The resistance of a material to thermo-oxidative attack by atomic oxygen ANTISYMMETRY Special symmetry with sign change between off-diagonal components, e.g. an unsymmetrical angle-ply laminate AO Atomic oxygen; experiments conducted on the Long Duration Exposure Facility (LDEF) AOCS Attitude and Orbit Control System, or subsystem APC Aromatic polymer composite AQUEOUS CORROSION Corrosion by ionic species in water, e.g. chlorides, hydroxides. Includes moisture or humidity trapped or condensed within structures. AR Acceptance Review ARA Advanced rigid array; a type of ultrasonic transducer assembly ARALDITE"! A range of epoxy-based structural adhesives; developed by Ciba Geigy, now Vantico ARALL"! Aramid fibre-reinforced aluminium laminate. [See: FIBRE METAL LAMINATE] ARAMID A type of highly oriented aromatic polymer material. Used primarily as a high-strength reinforcing fibre, of which Kevlar"! 49 and Twaron"! HM are most commonly used in aerospace applications ARAMID/EPOXY A composite material comprising of an aramid fibre reinforcement in an epoxy matrix ARC Austrian Research Centre, Seibersdorf ARD Atmospheric Re-entry Demonstrator AREAL WEIGHT A measurement of the weight per unit area of a fabric or fabric prepreg; expressed as g/m ARIANE Family of European launch vehicles ARP Aramid fibre-reinforced plastic, Ref. [10] ARTIFICIAL INTELLIGENCE (AI) The property of a machine capable of reason by which it can learn functions normally associated with human intelligence As Austenite start temperature ASIFS Aerial spacecraft interface structure; part of SILEX ASIP Aircraft Structural Integrity Program ASME American Society of Mechanical Engineers ASSEMBLED ARTICLE Any component black box or assembly of components which represents the article to be used in a spacecraft, Ref. [7]. ASSEMBLY An accumulation of subassemblies and/or equipment that performs specific functions within a subsystem, e.g. water pump package. (Verification level typical of US standard), Ref.[1] ASTM American Society for Testing and Materials; USA standards organisation ASTP Advanced Systems and Technology Programme; ESA programme ASTREX Advanced space structure technology research experiments; an American smart technology programme ATC 1 Active Thermal Control 2 Advanced Technical Ceramic ATOMISATION Spray technique for producing metal alloy powders with or without a particulate reinforcement. Molten metal is forced through a nozzle into a stream of high-velocity, inert gas. The semi-solid droplets are collected on a substrate. Proprietary processes are OSPREY (un-reinforced alloys) and COSPRAY (particulate reinforced alloys) ATOX Atomic Oxygen AUTOCLAVE A closed vessel for conducting a chemical reaction or other operation under pressure and heat AUTOCLAVE MOULDING After composite lay-up, the entire assembly is placed in steam autoclave at 7 bar to 14 bar and 180C; additional pressure achieves higher reinforcement loading and improved removal of air AVCO 5026-39 HCG Epoxy-novalac, glass fibre honeycomb reinforced material AVERAGE STRESS CRITERION A failure criterion in which it is assumed that failure occurs when the average stress over some distance equals the unnotched laminate strength AWG American Wire Gauge AXIAL WINDING In filament-wound reinforced plastics, a winding with the filaments parallel to the axis AXISYMMETRY Symmetry about an axis (in the case of a laminated material it is isotropic in the plane normal to the axis, and this material is called transversely isotropic) B B-BASIS DESIGN ALLOWABLE A value which at least 90 % of the population of values is expected to fall with a confi-dence of 95 %, Ref. [9]; also known as B value B-SCAN A scanned line response showing features at identifiable depths; nondestructive testing B-STAGE An intermediate stage in the reaction of certain thermosetting resins, Ref. [10], in which the material swells when in contact with certain liquids and softens when heated, but cannot dissolve or fuse entirely; sometimes referred to as resistol. The resin in an uncured prepreg or premix is usually in this stage. [See also: A-STAGE, C-STAGE] 'B' VALUE A 'B' value is that above which at least 90% of the population of values is expected to fall with a confidence of 95%. [See also: ALLOWABLES] BACKING SHEET A thin polymer sheet used to protect prepreg and film adhesive surfaces from contamination and damage prior to use. These have to be completely removed during lay-up and are usually coloured to aid this. BAe British Aerospace, UK BAGGING Process: the enclosing of an uncured composite lay-up in a heat-resistant bag prior removal of the air and subsequent curing BAKEOUT Activity of increasing the temperature of hardware to accelerate its outgassing rates with the intent of reducing the content of molecular contaminants within the hardware. Note: Bakeout is usually performed in a vacuum environment but may be done in a controlled atmosphere, Ref. [8]. BALANCED DESIGN In filament-wound reinforced plastics, a winding pattern so designed that the stresses in all filaments are equal BALANCED LAMINATE Where plies with positive angles are balanced by equal plies with negative angles. While angle-ply laminates have only one pair of matched angles, balanced laminates can have many pairs, plus 0 and 90 degrees. A balanced laminate is orthotropic in in-plane behaviour, but anisotropic in flexural behaviour BAM Bundesanstalt fr Materialforschung und prfung, Federal Institute for Materials Research and Testing, Germany BATCH Materials produced during a unique sequence: 1. Fibre: The amount which is produced by the conversion of a number of precursor tows under standard, controlled, processing-plant conditions in one continuous operation, including any surface treatment and sizing of the fibre 2. Prepreg: A quantity, irrespective of width, that is produced under 'no-change conditions' in one continuous operation of the impregnating plant from one batch of resin mix and one batch of fibre. A batch is expected to conform to a fixed manufacturing process and to have homogeneous properties within prescribed tolerances over its whole width and length. A maximum allowable length for a prepreg batch is sometimes specified 3. Resin: A quantity of resin in either film or liquid form produced from one mix of resins, resin modifiers and curing agents BERYLLIUM (Be) Metallic element, melting point 1289C, density 1850 kg m-3. Uses: aerospace structural material, with good dimensional stability and moderately high service temperatures. BIAS A type of weave for a fabric, [See: BIAS WEAVE] BIAS WEAVE The weft picks cross the warp ends at 45 or 60 instead of the normal 90. BIAXIAL WINDING In filament winding, a type of winding in which the helical band is laid in sequence, side by side, with no crossover of fibres BIDIRECTIONAL LAMINATE A reinforced plastic laminate with the fibres oriented in two directions in the plane of the laminate; a cross laminate. [See also: UNIDIRECTIONAL LAMINATE] BIG FOOT"! Types of mechanical fasteners that provide a larger footprint, i.e. contact area, than conventional types of fasteners; developed by Monogram BIOMIMETICS Synthetic materials which function like natural ones, e.g. artificial tendons and Velcro"! BIOPAN A multi-user exposure facility, designed for exobiology, radiation biology, radiation dosimetry and material science investigations in space; ESA mission BIPROPELLANT Rocket fuel consisting of two chemical components which react on contact in the combustion chamber, e.g. mono-methyl-hydrazine (MMH) and nitrogen tetroxide (NTO) BISFA International Bureau for Standardisation of Man-made Fibres BISMALEIMIDE (BMI) A type of polyimide that cures by an addition rather than a condensation reaction, thus avoiding problems with volatiles, and which is produced by a vinyl-type polymerisation of a polymer terminated with two maleimide groups. It has intermediate temperature capability between epoxy and polyimide (about 200C) BLEED The removal of excess resin from a prepreg during processing, [See also: CONTROLLED BLEED and ZERO-BLEED] BLEEDER CLOTH Non-structural, fibre glass cloth placed adjacent to the composite material part to absorb excess resin during cure, and removed from the part after cure BLIND Fasteners: Installed from one side of a component only BLISK Turbine disk where the blades and hub are formed as a single piece (Integrally-bladed disk). BLISTER Delamination in a distinct local area or areas BLOX Laser enhanced oxidation test facility at ONERA, France. BMI Bismaleimide. [See: BISMALEIMIDE] BOND LINE The area between two materials that have been adhesively bonded; includes the layer of adhesive between the adherends BOND STRENGTH The amount of adhesion between bonded surfaces; a measure of the stress required to separate a layer of material from the base to which it is bonded. [See also: PEEL STRENGTH] BONDED JOINT The general area of contact for a bonded structure. This includes composite to composite and composite to metal adherends and all forms of adhesives including co- and post-cured joints. [See also: ADHEREND, ADHESIVE, CO-CURE, POSTCURE] BOR-4 A re-entry test vehicle BORON (B) Metallic element, melting point 2092C, density 2340 kg m-3. Uses: alloying additions, doping in aluminides to induce ductility. Reinforcing filaments for polymer or metal matrix composites. Mainly within the USA BORON CARBIDE (B4C) Extremely hard ceramic material with a density of 2520 kg m-3 BORSIC Boron filaments for reinforcement made by deposition onto a fine tungsten wire and coated with silicon carbide (SiC) BPS Backpack subsystem; part of an extra-vehicular activity space suit BRAGG GRATING A diffraction grating constructed by creating a systematic spatial variation of the structure of a material, such as the molecular structure of a crystal or the refractive index of glass, Ref.[4]. BRAIDING Process: A mechanical weaving of fibres that enables three or more continuous yarns to be progressively crossed in a predetermined pattern and angle to produce a complex network to form a structural shape, such as a tube, square box or U-shaped channel BRAZING Joining technique involving the melting of a material with a lower temperature (braze) placed between parts to be joined. The parent metal(s) remain(s) solid during brazing BREADBOARD [See: DEVELOPMENT MODEL] BREATHER Porous material, such as fabric or mat, placed inside the vacuum bag to facilitate removal of air, moisture and volatiles during cure BRIDGING A build-up of solder or conformal coating between parts, component leads and/or base substrate forming an elevated path BROOMING The appearance of the end of a failed composite material where the reinforcing fibres are clearly visible, such that it resembles a brush or broom BS British standard, controlled by the British Standards Institute (BSI). BSI British Standards Institute, UK BUCKLING 1 Unstable displacement of a structural part, such as a panel, caused by excessive compression or shear. Micro-buckling of fibres in a composite material can also occur under axial compression 2 Fibre: a failure mechanism which occurs under compressive loads where the reinforcing fibres in a composite are displaced transversly; fibre buckling modes are known as extension mode and shear mode. BUNDLE A number of parallel filaments, normally without organic matrix BUNDLE STRENGTH Strength obtained from a test on parallel filaments, with or without organic matrix. The bundle test is often used instead of the monofilament test BURAN Russian reusable manned spacecraft: resembling the USA STS Space Shuttle Orbiter BURST PRESSURE The pressure at which a pressurized system ruptures or collapses, Ref. [5] BURST STRENGTH Hydraulic pressure required to burst a vessel of given thickness; commonly used in testing filament-wound composite structures BVID Barely visible impact damage C C-C Carbon-carbon. Carbon fibre reinforced, carbon matrix composite C/SiC Carbon fibre-reinforced silicon carbide; a ceramic matrix composite (CMC) C-STAGE The final stage in the reaction of certain thermosetting resins in which the material is relatively insoluble and infusible; sometimes referred to as resite. The resin in a fully cured thermoset moulding is in this stage. [See also: A-STAGE, B-STAGE] CABLE Two or more insulated conductors, solid or stranded, of equal length, contained in a common covering; or two or more insulated conductors, of equal length, twisted or moulded together without common covering; or one insulated conductor with a metallic covering shield or outer conductor (shielded cable or coaxial cable) CABLED YARN [Technical textiles] Two or more folded yarns twisted together CADMIUM (Cd) Metallic element, melting point 321C, density 8650 kg m-3, Uses: alloying additions, protective coatings: NOT FOR SPACE USE C/Al Carbon fibre reinforced aluminium CAI Compression after impact CALIBRATION The comparison of two instruments or measuring devices, one of which is a standard of known accuracy traceable to national standards, to detect, correlate, report, or eliminate by adjustment any discrepancy in accuracy of the instrument or measuring device being compared with the standard CANOPY The fabric portion of a parachute which provides drag, or drag and lift, when inflated CAPSA Alenia Spazio ablative TPS design tool computer program CARBIDE A binary compound of carbon with an element more electropositive than carbon, (excluding carbon-hydrogen compounds). Compounds often hard and brittle. Uses: external hardening treatment for steels, as hardening agents within alloys; e.g. silicon carbide is a widely used abrasive in particulate form, or as a matrix for ceramic matrix composites. Carbides, important alloying element in steels and superalloys CARBON (C) Non-metallic element, melting point ~3550C; graphite sublimes at ~3367C; density 2200kg m-3. Uses: carbon reinforcement fibres, matrix in C-C composites, silicon, tungsten. [See also: CARBIDE and CARBON FIBRE] CARBON/EPOXY A composite material comprising of a carbon fibre reinforcement in an epoxy polymer matrix CARBON FIBRE Fibre produced by the pyrolysis of organic precursor fibres, such as rayon, polyacrylonitrile (PAN) and pitch, in an inert environment. The term is often used interchangeably with the term graphite; carbon fibres and graphite fibres do, however, differ. The basic differences lie in the temperature at which the fibres are made and heat-treated, and in the amount of elemental carbon produced. Carbon fibres typically are carbonised in the region of 1315C and assay at 93 to 95% carbon, while graphite fibres are graphitised at 1900C to 2480C and assay at more than 99% elemental carbon CARBON-CARBON Carbon fibre-reinforced carbon, produced by resin or pitch pyrolysis of the matrix of a CFRP, or by CVI; infiltration of a fibrous preform. [See: CVI] CARE Carbon fibre-reinforced aluminium laminate. [See: FIBRE METAL LAMINATE] CARINA Space recovery vehicle, by Alenia Spazio: CApsula di RIentro Non Abitata CARPET PLOT A design chart showing the uniaxial stiffness or strength as a function of arbitrary ratios of 0, 90 and 45 plies; used for determination of moduli, strength or thermal expansion coefficients CARTEC-FT Study for an Italian scientific payload carrier for re-entry experiments CAS Calcium aluminosilicate: a glass-ceramic matrix CASA Construcciones Aeronauticas SA, (E); now EADS CASA CASE Case describes the whole structure which is necessary for pressure storage. It consists of the pressure vessel, the joint structure and the interface flange providing the connection to the main structure CASSINI-HUYGENS NASA Cassini mission to study Saturn, it's rings and moons. The ESA-built Huygens probe is for decent onto Titan, the largest Saturn moon. CAT Computer-aided tomography CATALYST A substance that changes the rate of a chemical reaction without itself undergoing permanent change in its composition; a substance that markedly speeds up the cure of a compound when added in a quantity small compared with the amounts of primary reactants CATASTROPHIC HAZARD A potential risk situation that can result in loss of life, in life-threatening or per-manently disabling injury, in occupational illness, loss of an element of an interfacing manned flight system, loss of launch site facilities or long term detrimental environmental effects. Note: For payloads of the NASA STS or ISS, the applicable definition is: A potential risk situation that can result in personnel injury, loss of the NASA orbiter, ground facilities, or STS equipment; (LASTS 1700.7, paragraph 302), Ref. [5] CAUL PLATE Smooth metallic plate that is placed in contact with the laminate or adhesively bonded assembly to ensure uniform pressure and temperature during cure and a smooth finish afterwards CBEN Cantilever beam enclosed notch; a test method used for Mode II fracture toughness C-C Carbon-carbon composite material CCB Configuration Control Board CCD Charge-coupled Device CCDTV Charged-couple device television CCSiC Carbon-carbon-silicon carbide composite material CDA Copper Development Association CDR Critical Design Review CDS Characteristic damage state CEN Comit Europen de Normalisation (European Committee for Standardization) CERAMIC Chemical compound or mixture of compounds with high temperature capabilities, often metal (or silicon) oxides, nitrides or carbides CERAMIC MATRIX COMPOSITE (CMC) Composite material in which the matrix is a ceramic CETEX Ceramic Tile Experiment (on EXPRESS) CFD Computational Fluid Dynamics CFRP Carbon fibre-reinforced plastic. Letter G in this handbook stands for Glass, whereas in American publications it is used for graphite. [See also: GFRP] CFRTP Carbon fibre-reinforced thermoplastic CHA Ceramic Heatshield Assembly CHAR YIELD The amount of material remaining after ignition and burning CHARACTERISTIC DAMAGE STATE (CDS) A characteristic level at which the amount of cracking induced in a laminate by cyclic loading stabilises CHEMICAL VAPOUR DEPOSITION (CVD) Processing method involving the decomposition of a pre-cursor gas rich in the elements required under controlled temperatures and pressures (in a reaction vessel) and deposition onto a component or onto reinforcement fibres. Applicable to metals and ceramic (most common). Uses: coatings and thin section carbon or ceramic matrix composites. Deposition rates are slow, unless substrates are heated (pyrolysis) or laser heat sources (photolysis) are used CHEMICAL VAPOUR INFILTRATION (CVI) Same principle as CVD. Term often used to describe the Near-net shape processing method for matrix deposition within fibre preforms. Deposition rates are slow. Proper infiltration of thicker section composites can require thermal gradients or forced flow techniques. Uses: ceramic and carbon matrix composites [See also: NEAR-NET SHAPE] CHROMIA Chromium Oxide (Cr2O3) CHROMIUM (Cr) Metallic element, melting point ~1863C, density 7180 kg.m-3, Uses: Addition for corrosion (oxidation) resistance in superalloys, steels, coating systems CI Configuration Item Number (as per project definition) CIRCUIT In filament winding: (1) One complete traverse of the fibre-feed mechanism of a winding machine. (2) One complete traverse of a winding band from one arbitrary point along the winding path to another point on a plane through the starting point and perpendicular to the axis CIRCUMFERENTIAL ('CIRC') WINDING In filament-wound reinforced plastics, a winding with the filaments essentially perpendicular to the axis CLEANROOM A room in which the concentration of airborne particles is controlled, and which is constructed and used in a manner to minimize the introduction, generation, and retention of particles inside the room, and in which other relevant parameters, e.g. temperature, humidity, pressure; are controlled as necessary, [BS EN ISO 14644-1:19991 3.1.3], Ref. [8] CLOTH A manufactured assembly of fibres or yarns with sufficient mechanical strength to hold the assembly together when handled; a fabric more than 150 mm wide. [See also: FABRIC] CLRD Common large reflector dish CLS Cracked lap shear; a test method used for mixed fracture toughness modes I and II CMBR Cosmic microwave background radiation CMC Ceramic matrix composite CME See: COEFFICIENT OF MOISTURE EXPANSION CMR Creep mismatch ratio. In a composite material, the ratio of the creep rate of the fibres to that of the matrix CN Centre notch; a test method used for fracture toughness mode I CNC Computer numerical control COATING 1 A material applied to protect a substrate material or assembly, Ref. [10], e.g. against corrosion, oxidation or diffusion COBALT (Co) Metallic element, melting point 1495C, density 8900 kg.m-3, Uses: base element for some superalloys, binder for cemented carbides (tungsten carbide), alloying addition to other superalloys CO-CURE Simultaneous curing and bonding of a composite laminate to another material or parts, such as honeycomb core or stiffeners, either by using the adhesive properties of the composite resin or by incorporating an adhesive into the composite lay-up COEFFICIENT OF MOISTURE EXPANSION (CME) The change in length per unit length produced by the absortion of water (usually by resin matrices or adhesives) COEFFICIENT OF THERMAL EXPANSION (CTE) The change in length per unit length produced by a unit rise or decrease in temperature COHESION The requirement that the constituent components of the prepreg remain united in the required format for the specified storage and handling conditions. (Specific definition for 'cohesion' in relation to prepreg) COLLECTED VOLATILE CONDENSABLE MATERIAL (CVCM) The quantity of outgassed matter from a test specimen that condenses on a collector maintained at a specific temperature for a specific time, Ref. [8]. Note: CVCM is expressed as a percentage of the initial specimen mass and is calculated from the condensate mass determined from the difference in mass of the collector plate before and after the test COMBINED TEST Test imposing the environments in the logical combination, rather than sequentially, to evaluate the synergistic effects between environments, Ref.[1] COMED Constellations and multimedia development and demonstration programme; a DLR (D) telecommunications technology demonstration programme completed in 2004 COMET Commercial Experiment Transporter (NASA) two function recovery capsule. Free-flyer concept of a pressurised recovery system (intended for 227 kg of recoverable experiments) with a non-pressurised, non-recoverable service module CO-MINGLING A process whereby thermoplastic fibres are mixed with reinforcing fibres within a yarn COMPATIBILITY The ability of two or more substances combined with each other to form a homogeneous composition with useful plastic properties. (Specific definition for 'compatibility' in relation to composites.) COMPLIANCE Measurement of softness as opposed to stiffness of a material. It is the reciprocal of Young's modulus, or an inverse of the stiffness matrix COMPONENT A device which performs an electronic, electrical or electromechanical function and consists of one or more elements joined together and which cannot normally be disassembled without destruction. The terms component and part can be interchanged. Typical examples of components are transistors, integrated circuits, hybrids, capacitors COMPOSITE SANDWICH CONSTRUCTION A panel composed of a lightweight core material, such as honeycomb, foamed plastic, and so forth, to which two relatively thin, dense, high-strength or high-stiffness faces or skins are adhered, Ref. [9] CONDITION Metal alloys: a sequence of heat-treatment or mechanical working, which determines the metallurgical structure and hence properties CONDITIONING One or more processes applied to samples prior to testing, e.g. to increase or decrease the moisture content, heat treatment, thermal cycling CONDITION MONITORING Smart technologies: A diagnostic system which can provide data on the integrity or functioning of machinery, industrial plant or a space subsystem, either continually or periodically CONDUCTOR A lead or wire, solid or stranded, or printed-circuit patch serving as an electrical interconnection between terminations CONFORMAL COATING Material applied to protect an electronic assembly, Ref. [10]. A thin protective coating which conforms to the configuration of the covered assembly CONSOLIDATED DECLARED LIST A prime contractor task which consists of: - sorting by part, material or process group and merging the items from subcontractors lists into one project list - summing up in one item, identical items from different subcontractors, - negotiating the reduction to one or a few items, where identical functions are performed by an excessive number of parts, [See also: DML, DMPL, DPL] CONSOLIDATION A stage in the manufacturing process used to create a composite from either fibres and matrix phases or pre-prepared plies, e.g. thin metal foils, metallised reinforcement fibres or prepregs. Often requires heating and pressure to achieve proper consolidation. Processes can be repeated CONSTITUENT MATERIALS Individual materials that make up the composite material; e.g. carbon and epoxy are the constituent materials of a carbon/epoxy composite material CONTAINMENT A technique that, if a part fails, prevents the propagation of failure effects beyond the container boundaries, Ref. [5] CONTAMINATION Particles, liquids, gases, materials and micro-organisms which by their presence can disturb the performance of an item CONTINUOUS FILAMENT YARN Yarn formed by twisting two or more continuous filaments into a single continuous strand CONTINUOUS REINFORCEMENT Where reinforcement fibres or filaments pass uninterrupted through the composite CONTROLLED BLEED Prepreg materials that contain a resin which is formulated to have flow and gelation characteristics such that excess resin is removed in a controlled manner during consolidation and curing of a composite CONVENTIONAL METALS Engineering metals and alloys which do not contain deliberate additions of particulate or fibre reinforcements, i.e. are not considered as composites COPPER (Cu) Metallic element, melting point 1085C, density 8960 kg.m-3, Uses: high thermal and electrical conductivity applications CORE Sandwich panel: a lighweight material in between the face skins, e.g. honeycomb core, foam. Metallic or composite sheet materials are bonded to the core to form a sandwich panel CORE SPLICE A joint or the process of joining one type of core to another; usually achieved by adhesive bonding using an adhesive with gap-filling properties CORNING DC 235 SILICONE Commercial silicone-based material produced by Corning CORROSION A reaction of the engineering material with its environment with a consequent deterioration in properties of the material, Ref. [9] Note: The reaction can be chemical or electrochemical COUNT (Fabrics) Number of warp and fill yarns per unit length; e.g. a fabric count of 24 x 26 in English units means 24 yarns per inch in the warp, and 26 in the fill COUPLANT A substance placed between an ultrasonic transducer and the material under test to ensure a good acoustic path COUPLING Linking a side effect to a principal effect. Poisson coupling links the lateral contraction to an axial extension. For composite materials, an anisotropic laminate couples the shear to normal components; an unsymmetric laminate couples curvature with extension. These couplings are unique with composites and provide opportunity to perform extraordinary functions COUPON A small test specimen, e.g. usually a flat laminate, for evaluation of basic lamina or laminate properties or properties of generic structural features (e.g. bonded or mechanically fastened joints) CP Commercial Purity (Metal alloys, notably Titanium) CPASB Coarse pointing areal support bracket; part of SILEX CPM Coarse pointing mechanism; part of SILEX CPN Corps de Propulseurs Poudre. CPS Chestpack subsystem; part of an extra-vehicular activity space suit CPU Central Processing Unit CR Commissioning Review CRACK 1 A defect that behaves like a crack that is initiated, for example, during material production, fabrication or testing or developed during the service life of a component. Note: The term crack in this definition includes flaws, inclusions, pores and other similar defects, Ref. [5]; also known as CRACK-LIKE DEFECT 2 Composite: An actual separation of moulding material visible on opposite surfaces of the part and extending through the thickness; a fracture CRACK ASPECT RATIO For a part-through crack, the ratio of crack depth, a, to half crack length, c, i.e. a/c, Ref. [5] CRACK GROWTH Rate of propagation of a crack through a material due to a static or dynamic applied load CRACK GROWTH RATE (da/dN, dc/dN, da/dt or dc/dt) The rate of change of depth a or length c with respect to the number of load cycles N or time t, Ref. [5] CRACK GROWTH RETARDATION The reduction of crack-growth rate due to intermittent overloading of the cracked structural member, Ref. [5] CRACK-LIKE DEFECT A defect that behaves like a crack, [See: CRACK] CRAF Comet rendezvous and flyby CRAG Composite Research Advisory Group, UK CRAZING Fine discontinuity which can extend in a network on or under the surface of a plastic material CREEP The deformation (permanent change in dimensions) of a material (plastic, metal or ceramic) under constant load over a period of time, not including the initial instantaneous elastic deformation. A process which generally becomes significant at elevated temperatures, at room temperature it is sometimes called cold flow CREVICE CORROSION A form of galvanic corrosion occurring within a single phase where a gradient environment exists. [See also: GALVANIC CORROSION] CRITICAL CRACK The critical crack size (ac) defined as the crack size at which the structure fails under limit load, calculated for brittle fracture by:  EMBED Equation.3  where: KC = critical stress intensity factor Si = limit stresses Fi = stress intensity magnification factors : for different load cases Note: Factors Fi normally depend on the crack size (a), and is accounted for in the calculations, e.g. by use of an iterative method CRITICAL FLAW A flaw of sufficient size and shape to cause unstable growth to occur under the specific operating loads and environment CRITICAL HAZARD A potential risk situation that can result in, Ref. [5]: temporarily disabling but not life-threatening injury, or temporary occupational illness; loss of, or major damage to, flight systems, major flight system elements or ground facilities; loss of, or major damage to, public or private property; or short-term detrimental environmental effects CRITICAL MECHANICAL PART Mechanical part that requires specific attention or control due to fracture mechanics aspects and limited-life aspects, or with which the Contractor has no previous experience, Ref. [6] CRITICAL PROCESS A process is declared critical when it is new or nonvalidated for the application in question or has caused problems during previous use that remain unresolved, Ref. [6] CRITICAL STRAIN The strain at the yield point CRITICAL STRESS-INTENSITY FACTOR (FRACTURE TOUGHNESS) The value of the stress-intensity factor at the tip of a crack at which unstable propagation of the crack occurs. This value is also called the fracture toughness. The parameter KIC is the fracture toughness for plane strain and is an inherent property of the material. For stress conditions other than plane strain, the fracture toughness is denoted KC. In fracture mechanics analyses, failure is assumed to be imminent when the applied stress-intensity factor is equal to or exceeds its critical value, i.e. the fracture toughness, [See Stress intensity factor (K)], Ref. [5] CROSS-LINKING 1 Applied to polymer molecules, the setting-up of chemical links between the molecular chains. When extensive, as in most thermosetting resins, cross-linking makes one infusible super-molecule of all the chains 2 The chemical reaction that occurs in thermosetting polymers due to the heat applied during the cure CROSS-PLY Composites containing plies of material, normally prepreg, at angles of 0 and 90 CROSS-PLY LAMINATE Special laminate that contains only 0 and 90 plies. This bidirectional laminate is orthotropic and has nearly zero Poisson's ratio. The other simple bidirectional laminate is the angle-ply, which possesses one pair of balanced off-axis plies CRV 1 Crew Return Vehicle 2 Crew Rescue Vehicle CRYOFORMING Forming (shaping) of metal alloys at very low temperatures, e.g. stainless steels CRYOGENIC Very low temperature, generally less than 100 K. Typically the temperature ranges at which the principal atmospheric gases liquify, e.g. Nitrogen: -196C CRYOMILLING Mechanical attrition in liquid nitrogen CRYOTANK A tank structure containing a liquid or gas (often fuel) at cryogenic temperatures, [See also: LOX and LH] CRYSTALLINITY (DEGREE OF) The volume fraction of crystallites within the polymer C-SAM C-scan scanning acoustic microscope; an ultrasonic materials evaluation technique C-SCAN The area-scanning of a specimen with ultrasonic acoustic waves. A non-destructive testing technique for finding voids, delaminations and defects in fibre distribution, [See also: A-SCAN and B-SCAN] CSG Centre Spatial Guyanais C-SiC Carbon-silicon carbide composite material CSLDV Continuously Scanning Laser Doppler Vibrometer CSM Chopped strand matt; a type of multidirectional, short-fibre reinforcement used for industrial materials rather than high-performance aerospace composites CT Computer or computerised tomography CTE See: COEFFICIENT OF THERMAL EXPANSION CTE MISMATCH 1 The difference in coefficient of thermal expansion between two or more materials within a specified temperature change, e.g. polymers and metals, Ref. [10]. 2 The difference in coefficient of thermal expansion between a reinforcement and the matrix or a coating and substrate within a specified temperature rise, e.g. carbon fibre (low/zero CTE) and Al alloy (large +ve CTE) CTP Cold thermal protection CTV Crew Transfer Vehicle CURE 1 To change the properties of a polymer-based material by chemical reaction accomplished by heat or catalyst (or both) and with or without pressure, e.g. resin, adhesive, coating, Ref. [10]. 2 A chemical reaction during which a liquid resin is transformed to a solid material by the process of cross-linking CURE CYCLE 1 The relationship between time, temperature and pressure required to achieve the required cure and properties of a polymer-based material, e.g. resin, adhesive, coating, Ref. [10]. 2 The cure cycle can include defined heat-up and cool-down rates, isothermal holds for specified periods and application and removal of negative or positive pressures at defined times or temperatures. The optimum cure cycle is usually specific to a particular type of prepreg, its lay-up and the component and tool design. Small variations in the prepreg (in particular in the resin) can have a dramatic effect on the cure cycle needed to achieve a satisfactory laminate CURE STRESS A residual internal stress produced during the curing cycle of a composite structure CURIE POINT The temperature at which a material begins to lose its piezoelectric characteristics. Once lost the process is irreversible, though the material can be recoverable by re-poling CURING AGENT Hardener, a catalytic or reactive agent added to a resin to cause polymerisation CURING TEMPERATURE Temperature at which a cast, moulded or extruded product, a resin-impregnated reinforcement or an adhesive is subjected to curing CURING TIME The length of time a part is subjected to heat or pressure, or both, to cure the resin; interval of time between the instant relative movement between the moving parts of a mould ceases and the instant pressure is released. Note: Further cure can take place after removal of the assembly from the conditions of heat or pressure.[See: POST CURE] CVCM Collected Volatile Condensable Matter CVD Chemical Vapour Deposition CVI Chemical Vapour Infiltration CVI-C/SiC Carbon-silicon carbide composite material manufactured by MAN Technologie (D), using Chemical Vapour Infiltration process. CVSR Comet Nucleus Sample Return mission CYANATE ESTER A family of polymer resins, which can contain bisphenol, phenol or novalac within their formulations, that provide a low moisture absorption capability CYCLE Processing of composites: The complete, repeating sequence of operations in a process or part of a process. In moulding, the cycle time is the elapsed time between a certain point in one cycle and the same point in the next CYCLIC LOADING A fluctuating load (or pressure) characterized by relative degrees of loading and unloading of a structure. Examples are loads due to transient responses, vibroacoustic excitation, flutter and oscillating or reciprocating mechanical equipment, Ref. [5] D DADT Differential absorption distributed thermometry. A fibre-optic-based temperature-measurement method DAISY Deployable antenna integral system; an antenna design from Dornier DAMAGE A structural degradation or anomaly caused by service conditions or by abnormal operation, e.g. impact damage caused by dropped tools or other foreign objects DAMAGE ACCUMULATION Term used in fatigue testing of MMC and CMC materials where fatigue cracks initiated in the matrix phase propagate and cause debonding at the fibre-to-matrix interface, but do not damage the reinforcement DAMAGE CRITICAL PARTS Structural parts or items whose failure, due to the initiation or propagation of flaws or damages can result in loss of the mission or present a catastrophic hazard to personnel DAMAGE TOLERANCE The ability of a material, component or structure to retain an acceptable level of structural or environmental resistance properties under the effects of operational conditions, without risk of failing in a catastrophic manner, [See: DAMAGE TOLERANT] DAMAGE TOLERANCE CONTROL The application of design methodology, material and processing control, manufacturing technology, and quality assurance procedures to prevent premature structural failure due to the initiation or propagation of flaw or damage during fabrication, testing and service life DAMAGE TOLERANT A structure is considered to be damage tolerant if the amount of general degradation and/or the size and distribution of local defects expected during operation do not lead to structural degradation below limit-specified performance, Ref. [5] DAMPING The parameter which governs the resonant response of a mateial, component or structure; expressed quantitatively either as an absolute or a relative energy basis DAMPING (MECHANICAL) Mechanical damping gives the amount of energy dissipated as heat during the deformation of a material. Perfectly elastic materials have no mechanical damping DART Distributed anti-Stokes ratio thermometry. A fibre optic-based temperature measurement system DASA Deutsche Arbeitsschutzausstellung, German aerospace organisation; now Deutsche Aerospace Airbus DBTT Ductile-to-brittle transition temperature DCB Double cantilever beam; a test method used for fracture toughness Mode I (GIC) DC-XA Delta-Clipper Advanced Experimental Vehicle. An unmanned and rocket-powered, prototype vertical take-off and landing (VTOL) reuseable launch vehicle developed under NASA's SSTO programme by McDonnell-Douglas DDA Discontinuous Deformation Analysis DEBOND Area of separation within or between plies in a laminate, or within a bonded joint, caused by contamination, improper adhesion during processing, or damaging interlaminar stresses [See also: DELAMINATION]: 1 Adhesive bond: a delamination between the adherends 2 Sandwich panel: a delamination that occurs between the core and the face skin; caused by contamination or damage to either the film adhesive used to join the face skin laminate to the core, face laminate itself, bond area of the core or mechanical damage to core cell walls, by crushing or more local damage DEBOND General: a defective area of an adhesive bond where the adherends are no longer held together DEBRIS Accumulation of man-made waste materials in space, usually resulting from launch, deployment and other spacecraft operations DEBULK To reduce laminate thickness by application of pressure. The compaction is achieved by removing trapped air, vapour and volatiles between plies DEBULKING Process: to remove large volumes of air from prepreg materials during their lay-up on or into a mould, whereby some uncured plies of prepreg are formed to the mould surface using a vacuum bag, further plies added to the stack after the bag is removed. If necessary, it is repeated several times especially for thick laminates: a means of reducing porosity or voids in thick laminates or shaped details, e.g. corners DECLARED MATERIAL LIST (DML) Consolidated list of all materials used in a project, [See: CONSOLIDATED DECLARED LIST] DECLARED MECHANICAL PART LIST (DMPL) Consolidated list of all parts used in a project, [See: CONSOLIDATED DECLARED LIST] DECLARED PROCESS LIST (DPL) Consolidated list of all processes used in a project except for non-critical processes sufficiently described in the declared materials list, [See: CONSOLIDATED DECLARED LIST] DEFECT A manufacturing anomaly (crack, void, delamination) created by processing, fabrication or assembly procedures. [See also: FLAW] DEFLECTION Displacement of a structure such as a beam DEFORMATION Changes in size and shape of a body resulting from externally applied loads, temperature change, and moisture absorption. Deformation in size is measured by the normal strain components; that in shape, by shear component DEGRADATION The alteration of material properties (e.g. mechanical, thermal or optical) that may result from deviations in manufacturing or from repeated loading and/or environmental exposure, Ref. [10] DELAMINATION Physical separation or loss of bond of the layers of material in a laminate; locally or over a wide area DELTA CLIPPER McDonald Douglas single-stage-to-orbit (SSTO) spacecraft DEMONSTRATION A method of verification which consists of a qualitative determination of the properties of the test article. It is made through observation or actual conduct, which verifies characteristics such as human engineering features, and transportability. Note: Typical verification method of US standard. In the European standard Demonstration is part of Test, Ref.[1] DENIER A yarn and filament numbering system in which the yarn number is equal numerically to the weight in grams of 30 000 ft (9144 m) (used for continuous filaments). The lower the denier the finer the yarn DENSIFICATION The consolidation phase of a composite manufacturing technique in which pores or cracks are closed either by further infiltration or by the application of pressure at a specified temperature. DESIGN ALLOWABLE Material values that are determined from test data at the laminate or lamina level on a probability basis (e.g. 'A' or 'B' values), following ASTM or other test standards accepted by the final customer. [See also: A-BASIS DESIGN ALLOWABLE; B-BASIS DESIGN ALLOWABLE; 'A' VALUE, 'B' VALUE] DESIGN AND DEVELOPMENT PLAN This document is the master plan for the project Design and Development activities and gives high-level information on how the system design is to be carried out and which are the major guidelines for the system development, Ref.[1] DESIGN FEATURE An element or detail of a specific design that is not considered generically applicable to other structures for the purpose of substantiation (e.g. lugs and major joints). Such a design element or detail is qualified by a combination of test and analysis DESIGN VALUES/ PROPERTIES Material, structural-element and structural detail properties that have been determined from test data and chosen to assure a high degree of confidence in the integrity of the completed structure DETAIL A non-generic structural element of a more complex structural member (e.g. specific design-configured joints, splices, stringer run-outs, or major access holes) DEVELOPMENT Verification phase with the objective to support the design feasibility and select options able to satisfy manufacturing and performance requirements. The data acquired during this phase are also used to establish processes, procedures and test levels to support subsequent design, production, verification, maintenance and check-out activities. In principle, development is not used to achieve the formal verification close-out, Ref.[1] DEVELOPMENT MODEL Physical model used in support to the verification program during the development phase, mainly to confirm mathematical models and, in general, necessary in the areas of new design or where substantial redesign is required. Note: Development Model is also called Breadboard, Ref.[1] DHS Distributed hydrogen sensing. A fibre-optic-based measurement system DIAL Differential absorption LIDAR: two laser frequencies are used, with different absorbtion characteristics by an atmospheric molecule of interest. The measured aborbtions of the two then provide atmospheric chemical compostion information DIAPHRAGM MOULDING A shaping process technique applied to thermoplastic-based composites DIELECTRIC A material in which the electrical conductivity is zero or near zero DIFFERENTIAL SCANNING CALORIMETRY (DSC) Measurement of the energy absorbed (endothermic) or produced (exothermic) as a resin system is cured. Also permits detection of loss of solvents and other volatiles. DSC provides a means of assessing the cure characteristics of the supplied prepreg batch. Like HPLC, it is an analytical technique providing data on which to base comparisons. It can provide reaction start temperature, heats of polymerisation, temperature at peak maximum heat of polymerisation and glass transition temperature (Tg) of cure prepreg DIFFUSION BONDING (DB) Joining method for metals in which heated components are clamped together (in vacuum) enabling interdiffusion across the bond line. For bonds between components of the same material the resulting joint is metallurgically undetectable DIFFUSION Process of atomic movement of one element into another. Rate of diffusion increases with temperature. Generally implies solid-state diffusion, but also encompasses diffusion of gaseous species through solids DIFFUSION COATING Additional alloying elements introduced into the surface of a material by a process of material diffusion at high temperature, normally with strong, coherent oxide-forming elements such as chromium or aluminium to increase the corrosion resistance DIMENSIONAL STABILITY Zero or nearly zero deformation due to changes in temperature and moisture content: 1 Materials: A property of carbon/resin and aramid/resin composite materials that is exploited in the design of high-accuracy components in space, e.g. antennas or telescopes 2 Structures: Those which have to retain their physical shape and dimensions under the cyclic thermal conditions experienced in orbit, between -150C and +100C, typically DIMPLING Sandwich panels: the displacement under load of the face skins between the cellular structure of a honeycomb core DIN  HYPERLINK "http://www2.din.de/" Deutsches Institut fr Normung; German national standards organisation DIRECTIONAL SOLIDIFICATION (DS) Manufacturing method used to create a directional microstructure in a material, e.g. in superalloy turbine blades where grains are aligned in such a way as to resist the principal loads DIRECTIONALLY SOLIDIFIED EUTECTIC (DSE) Eutectic alloy composition which is directionally solidified to achieve the required microstructure; normally superalloys DISCONTINUOUS REINFORCEMENT Where the reinforcement phase consists of particles, whiskers or short fibres DISCREPANCY A manufacturing anomaly allowed and detected by the planned inspection procedure. It can be created by processing, fabrication or assembly procedures DISCRETE COMPONENT Any individually packaged electronic device, either active or passive, e.g. resistors, capacitors, inductors, diodes, transistors DISLOCATION An abnormality within a material lattice structure occurring along certain lines in the crystal structure. These take the form of stacking faults in the regular atomic pattern of the crystal. Deformation in metals occurs by the formation and movement of edge or screw dislocations. 'Cold work' - plastic deformation at low temperature - greatly increases the density of dislocations and anchors them to other dislocations, grain boundaries, the surface or other structural features. This pins crystallographic slip planes, so increasing material strength and reducing elongation to failure (work hardening) DISLOCATION DENSITY The number of dislocations within a given material volume. [See also: DISLOCATION] DISPERSION STRENGTHENING Increase of alloy strength due to a finely dispersed phase created by precipitated alloying constituents. Note: An optimum dispersion size and volume is required to maximise strength; deviation from the prescribed thermal treatment, in service or in manufacture, affects the strength DISPLACEMENT Measure of the movement of a point on the surface and in the interior of a body DISSIMILAR MATERIALS Materials with widely differing mechanical and physical properties: 1 materials which have different galvanic potentials, such that when they are in contact or joined together under particular environment conditions, e.g. moisture, temperature, there is a possibility of galvanic corrosion 2 materials which possess different thermal expansion characteristics 3 Joints: The coefficient of thermal expansion (CTE) is a critical property of materials to be joined DLR  HYPERLINK "http://www.dlr.de/" Deutschen Zentrum fr Luft- und Raumfahrt. German aerospace organisation DM Development Model DMA Dynamic mechanical analysis, [See: DYNAMIC MECHANICAL ANALYSIS] DML Declared Materials List DMPL Declared Mechanical Parts List DoD Department of Defense, USA DOME In a filament winding, the portion of a cylindrical container that forms the integral ends of the container DOPING Alternative term for MICRO ALLOYING DOT Department of Transportation, USA DOUBLE CANTILEVER BEAM SPECIMEN Interlaminar fracture toughness test specimen, frequently used for CFRP materials DOUBLER A sheet of material, made of either composite or metal, applied to a composite laminate or metal sheet to locally increase the properties, e.g. Locally built-up reinforcement or repair DPL Declared Processes List DRAFT The taper or slope of the vertical surfaces of a mould designed to facilitate removal of moulded parts. (Specific definition of 'draft' in relation to moulds.) DRAFT ANGLE The angle between the tangent to the surface at that point and the direction of ejection. (Specific definition in relation to moulds) DRAPE Ability of woven and non-woven composite materials to conform to a complex curvature surface, e.g. a fabric to a mould DRD Document Requirements Definition DRY LAY-UP Construction of a laminate by layering pre-impregnated reinforcement (partly cured resin) in a female or male mould, usually followed by bag moulding or autoclave moulding. [See also: PREPREG] DS 1 Directionally Solidified 2 Dispersion Strengthened; dispersion of particles in metal alloys DSC Differential scanning calorimetry, [See: DIFFERENTIAL SCANNING CALORIMETRY] DSDCB Double split double cantilever beam for Mode III DSE Directionally solidified eutectic DSS 1. Distributed strain sensor; A fibre-optic-based strain measurement system 2. Dimensionally stable structure 3. Dimensionally stable structures programme; and ESA programme DT Double torsion; a test method used for fracture toughness Mode I DTA Differential thermal analysis DTRC David Taylor Research Center, USA; a test method DTS Distributed temperature sensor or sensing. A fibre optic-based temperature measurement system DUCTILE-BRITTLE TRANSITION The temperature at which a metallurgical phase change in a metal alloy occurs and results in a sudden loss of ductility, e.g. tungsten below 400C DUCTILITY A measure of a material's plastic deformation. Often used to indicate maximum deformation prior to fracture DUPLEX MICROSTRUCTURE Two distinct phases within a material microstructure DWELL TIME Period of time during cure that a laminate is held at elevated temperature prior to application of pressure DWI Deviation Work Item DYNAMIC MECHANICAL ANALYSIS (DMA) DMA can be used on uncured prepreg and cured laminates to quantify some of their mechanical properties over a range of temperatures. DMA provides a measurement of storage modulus and loss-modulus in a shear or flexural mode. From these it is feasible to judge the cured material for consistency on expected modulus and modulus retention at elevated temperatures. The glass transition temperature (Tg) of cured material can also be determined. [See: LOSS-MODULUS] DYNAMIC MODULUS The ratio of stress to strain under vibrator conditions (calculated from data obtained from either free or forced vibration tests, in shear, compression, or elongation). [See also: DMA] DYNEEMA A high-performance fibre based on high modulus polyethylene, manufactured by DSM (NL) E E-GLASS A borosilicate glass containing less than 1% alkali (combined sodium and potassium oxides); the type most used for glass fibres for reinforced plastics; suitable for electrical laminates because of its high resistivity EAP Electroactive polymer (EAP) actuators are polymer materials or structures that change volume or shape when electric energy is supplied. Used in smart structures EB Electron beam; used in processes such as welding metals and curing resins EBM End-burning motor EB-PVD Electron Beam Physical Vapour Deposition. A method of depositing surface coatings EBW Electron Beam Welding ECLS Environmental Control and Life Support ECSS European Cooperation for Space Standardization. A cooperative effort of the European Space Agency, National Space Agencies and European industry associations for the purpose of developing and maintaining common standards, [See: ECSS website]. EDM Electrical discharge machining. Also called: spark eroding EDGE CLOSE-OUT [See: EDGE CLOSURE] EDGE CLOSURE Sandwich panels: Protects the core from accidental damage, serves as a moisture seal and provides edge reinforcement to enable transfer and distribution of edge attachment loads; also known as edge close-out and edge member EDGE MEMBER [See: EDGE CLOSURE] EDT Edge delamination tension; a test method for mixed Modes I and II EEE Electrical, electronic and electromechanical EFA European Fighter Aircraft; standards EFCB ESA Fracture Control Board E-GLASS Electrical glass; a grade of glass fibre. A borosilicate glass containing less than 1% alkali (combined sodium and potassium oxides); the type most used for glass fibres for reinforced plastics; suitable for electrical laminates because of its high resistivity EGSE Electrical Ground Support Equipment EIT Electrical Impedance Tomography ELASTIC MODULUS Stiffness ELASTIC RELATION Fully reversible, single-value, stress-strain relation. Loading and unloading follow the same path; there is no hysteresis, or residual strain. Although non-linear relation is ad-missible, the relation for composite materials is essentially linear ELASTIC-PLASTIC FRACTURE MECHANICS (EPFM) Adaptation of Linear Elastic Fracture Mechanics (LEFM) engineering principle to describe the propagation of a single crack through a material, usually a metal alloy, which assumes that the bulk of the material is behaving elastically, but compensates for plastic behaviour around the crack tip, [See: LEFM] ELECTRIC POLING The action of applying a strong electric field to orientate the dipoles within a ferroelectric ceramic as it is cooled through the ferroelectric transformation point. This conditions suitable materials (e.g. PVdF film) to produce piezoelectric effects ELECTROLYTE Galvanic corrosion: Any substance that provides an electrically conductive path between two dissimilar materials, e.g. moisture between carbon and aluminium ELECTRORHEOLOGICAL FLUIDS A class of fluids, consisting of colloidal dispersions in non-conducting liquids that exhibit a large, reversible change in their rheological behaviour when subjected to an external electric field ELECTROSTRICTIVE MATERIALS Solid materials which deform mechanically when subjected to an external electric field ELECTROSTRICTION An induced strain deformation that is independent of field polarity. A weaker effect than piezoelectricity. All dielectrics exhibit this behaviour ELEMENT 1 A part of a more complex structural member, e.g. skin, stringers, shear panels, sandwich panels, joints or splices, Ref.[1] 2 A composite of subsystems, capable of performing an operational role only in conjunction with other elements, e.g. Space Vehicle, Ground Segment, Space Station Pressurised Module, Ref.[1] ELONGATION Deformation caused by stretching; the fractional increase in length of a material stressed in tension. (When expressed as percentage of the original gauge length, it is called percentage elongation) ELS End loaded split; a test method EMA Electro-mechanical actuator; for X-38 test vehicle EMAT Electromagnetic acoustic transducer EMC Electromagnetic compatibility EMF Electromotive force EMI 1 Electromagnetic interference 2 Electro-mechanical impedance EN Euro Norme (European standard), [See: CEN] ENCAPSULATING COMPOUND An electrically non-conductive compound used for environmental protection which completely encloses and fills in voids between electrical components ENCB End notched cantilever beam; a test method used for thick laminates END A strand of roving consisting of a given number of filaments gathered together (the group of filaments is considered an end or strand before twisting and a yarn after twist has been applied); an individual warp yarn, thread, fibre or roving; in fabrics, the tows in the warp direction ENF End notch flexure; a test method used for fracture toughness Mode II (GIIC) ENGINEERING CONSTANTS Measured directly from uniaxial tensile and compressive, and pure shear tests applied to unidirectional as well as laminated composites. Typical constants are the effective Young's modulus, Poisson's ratio, and shear modulus. Each constant is accompanied by letter or numeric subscripts designating the direction associated with the property. (Specific definition for 'composites') ENGINEERING MODEL Physical model flight representative in form, fit and function, without redundancies and Hi-rel parts, used for functional qualification, except redundancy verification, failure survival demonstration and parameter drift checking, Ref.[1] ENGINEERING QUALIFICATION MODEL Physical model fully reflecting the design of the flight end item, except for the part standard (Mil-Grade parts are allowed, but procured from the same manufacturer of the Hi-rel parts), used for functional performance qualification (including verification of procedures for failure detection, confirmation, isolation and recovery and for redundancy management) and EMC testing, Ref.[1] ENS End loaded split; a test method used for Mode II used for thin laminates ENVIRONMENT External, non-accidental conditions (excluding mechanical loading), separately or in combination, that can be expected in service life and that can affect the structure, e.g. temperature, moisture, UV radiation and fuel EOM End of Mission EOS Earth observation satellite EPDM Ethylene propylene elastomer EPFM Elastic Plastic Fracture Mechanics EPOXY A family of thermosetting resins made by polymerisation of epoxides or oxiranes with other materials such as amines, alcohols, phenols, carboxylic acids, acid anhydrides, and unsaturated compounds; used for the matrix phase of composites and structural adhesives EQM Engineering Qualification Model EQUATOR In filament winding, the line in a pressure vessel described by the junction of the cylindrical portion and the end dome EQUIPMENT It is a functional unit that is viewed as an entity for purposes of analysis, manufacturing, maintenance, e.g. valves, batteries, individual electronic boxes, Ref.[1]. Note: In the US standard it is called Component EQUIPMENT CATEGORY Equipment classification on the basis of the qualification status, e.g. off-the-shelf, off-the-shelf with modifications, completely new, Ref.[1] ER Electro-rheological (fluid) ERC Earth Return Capsule ERS Earth resources satellite ES Electronic Shearography ESA European Space Agency ESA WLC TSTO Two-stage-to-orbit spacecraft from ESA Winged Launcher Concept programme ESACOMP A software package for the analysis and design of composite laminates and laminated structural elements; developed for ESA/ESTEC by Helsinki University and distributed by Componeering Inc ESACRACK A software package distributed by ESA. The package consists of the load- and stress-spectrum generation program ESALOAD, fracture mechanics analysis NASFLA, stress-intensity factors NASBEM, process crack growth material data NASMAT, fatigue analysis ESAFATIG, [See also: ESALOAD] ESALOAD A software programme that generates a load spectrum and a stress spectrum for a payload. The stress spectrum is generated using unit stress values, [See also: ESACRACK] ESD Electrostatic discharge ESH Equivalent sun hours ESIS Energy Standards Information System; test standards ESOC European Space Operations Centre, Darmstadt, Germany ESPI Electronic speckle pattern interferometry ESTEC European Space Research and Technology Centre, Noordwijk, NL ET External Tank. Space shuttle main external fuel tank ETAC Environmental Technical Applications Center, part of United States Airforce, USA; test standards ETCO-Odeillo Test centre, France ETFE Ethylene tetrafluoroethylene EURECA European Retrievable Carrier EUTECTIC ALLOY An alloy of two or more metals that has a single distinct melting point eV Electron volt EVA Extra-vehicular activity; human activity outside of a spacecraft (spacewalk) EXPANSION COEFFICIENT Measurement of the swelling expansion of composite materials due to temperature change and moisture absorption EXPERIMENT An item designed and built to accomplish a specific purpose which can be disassembled and retain its capabilities after re-assembly, Ref. [7] EXPRESS Experimental Re-entry Space System EXTRUSION A manufacturing method for metals, where a billet is forced through a die of the required shape. Often used to manufacture continuous lengths of materials with constant cross-sectional profiles. Materials can be heated for extrusion to reduce extrusion pressures or refine microstructure F FAA Federal aviation authority; controlling body for USA aircraft FABRIC General: any material of woven construction: 1 Reinforcement fabrics: fabrics constructed of reinforcing fibres, e.g. carbon, placed in more than the standard warp and weft fabric directions, e.g. 2-D fabrics; 2.5-D fabrics; 3- D fabrics 2 Technical textiles: interwoven fibres (warp and weft) of one or more fibre type In a finished fabric, the warp direction is the longitudinal thread direction, and the weft direction is the transverse thread direction Fabrics are specified by their fibre type, yarn type, knitting or weaving technique, weave style, fibre density, texture, pattern type, condition, length, width, density and thickness 3 Tape: a fabric of width less than 150 mm 4 Integrally woven: a triaxial fabric where all the reinforcement fibres are woven at the same time; also known as angle interlocked [See also: WEAVE, CLOTH, WARP, WEFT] FABRICATING, FABRICATION The manufacture of plastic products from moulded parts, rods, tubes, sheeting, extrusions, or other form by appropriate operations such as punching, cutting, drilling, and tapping. Fabrication includes fastening plastic parts together or to other parts by mechanical devices, adhesives, heat sealing or other means FACE 1 Outer ply of a laminate. 2 Covering sheets of a sandwich panel FACE SHEET A composite laminate or metal sheet that forms the external surfaces of a sandwich panel FACING A sheet material, usually thin and made of composite or metal, that is attached to a core material to form a sandwich panel; also known as face sheet FACTOR OF SAFETY The ratio of the design or ultimate loads to the limit or applied loads. [See: LOADS] FAIL-SAFE A Potentially Fracture Critical Item (PFCI) is fail-safe if it can be shown by analysis or test that, owing to structural redundancy, the structure remaining after failure of any element of the PFCI can sustain the new higher internal loads without losing limit specified performance. In addition, the failure of the item shall not result in the release of any part or fragment resulting in a catastrophic or critical event. [See also: PFCI] FAIL-SAFE (STRUCTURE) A damage-tolerance acceptability category in which the structure is designed with sufficient redundancy to ensure that the failure of one structural element does not cause general failure of the entire structure, Ref. [5] FAILURE (structural) The rupture, collapse, seizure, excessive wear or any other phenomenon resulting in an inability to sustain limit loads, pressures and environments, Ref. [5] FAILURE CRITERION Empirical description of the failure of composite materials subjected to a complex state of stresses or strains. The most commonly used criteria are the maximum stress, the maximum strain, and the quadratic criteria FAILURE ENVELOPE Ultimate limit in combined stress or strain state defined by a failure criterion FAILURE MODE The way in which a material degrades such that it can no longer support the applied loads leading ultimately to fracture 1 laminates: usually assessed by the behaviour of the individual layers and the interfaces between them, along with the laminate as a whole FAR Final Acceptance Review FASTENER Any item that joins other structural items and transfers loads from one to the other across a joint, [See: JOINT], Ref. [5] FATIGUE 1 In materials or structures, the cumulative irreversible damage incurred by cyclic application of loads in given environments. Fatigue can initiate and extend cracks, which degrade the strength of materials and structures, Ref.[5] 2 Progressive cracking mechanism caused by alternating stress FATIGUE LIFE The number of cycles of deformation required to bring about failure of the test specimen under a given set of oscillating conditions FATIGUE LIMIT The stress below which a material can be stressed cyclically for an infinite number of times without failure FATIGUE NOTCH FACTOR The ratio of fatigue strength of un-notched specimens at N cycles to the fatigue strength of notched specimens at N cycles FATIGUE STRENGTH 1 The maximum cyclic stress a material can withstand for a given number of cycles before failure occurs. 2 The residual strength of a material that has been subjected to fatigue FATIGUE STRENGTH RATIO The ratio of fatigue strength to static strength FATIGUE STRESS RATIO The ratio of the minimum to the maximum fatigue stress, usually denoted by R FAULT Manufacturing: an error or departure from the intended specified process which results in a defective material or structure FBH Flat bottom hole; a standard nondestructive testing calibration procedure FCI Fracture Critical Item FCIL Fracture Critical Item List FDEMS Frequency Dependent Dielectric Measurements FE Finite element FEA Finite element analysis FEM Finite element model or modelling FEI Flexible External Insulation; a thermal protection system (TPS) FEP Fluorinated ethylene-propylene co-polymer FERROELECTRICITY Reorientation of the dielectric dipoles of polar crystals by means of an applied field FESTIP Future European Space Transportation Investigations Programme; an ESA programme FFPI Fibre-Fabry-Prot Interferometer FFT Fast Fourier Transform. A digital signal analysis technique FGSE Fluidic Ground Support Equipment FIBER American term for a fibre. [See: FIBRE] FIBRE 1 Technical textiles: a general term for filamentary materials with a finite length at least 100 times their diameter. Also known as Filament or Spin Fibre 2 Single filament, rolled or formed in one direction, and used as the principal constituent of woven and non-woven composite materials FIBRE-COMPOSITE MATERIAL A material consisting of two or more discrete physical phases, in which a fibrous phase is dispersed in a continuous matrix phase. The fibrous phase can be macro-, micro- or sub-microscopic, but it has to retain its physical identity so that it can conceivably be removed from the matrix intact FIBRE CONTENT Percent volume of fibre in a composite material. Most common composites in use today have a fibre content between 45 volume % and 70 volume %. Percent weight of mass of fibre is also used FIBRE-CONTROLLED A laminate lay-up where the properties are largely determined by those of the fibre, e.g. 0/45/0/45/0 FIBRE DIAMETER The measurement of the diameter of individual filaments, in micrometres FIBRE/MATRIX INTERFACE The region separating the fibre and matrix phases, which differs from them chemically, physically, and mechanically. In most composite materials, the interface has a finite thickness (nanometres to thousands of nanometres) because of diffusion or chemical reactions between the fibre and matrix. Thus, the interface can be more properly described by the terms, 'interphase' or 'interfacial zone'. When coatings are applied to the fibres or several chemical phases have well-defined microscopic thicknesses, the interfacial zone can consist of several interphases FIBRE METAL LAMINATE (FML) Sheet or laminated material consisting of thin sheets of metal adhesively bonded with layers of fibre-reinforced polymer plies; often with various fibre directions. [See also: ARALL, GLARE and CARE] FIBRE OPTIC Pertaining to systems, subsystems, equipment and components in which optical fibres are used, Ref.[4] For smart technologies: one or more optical fibres used as sensors to measure some parameter of the light travelling within it that can in turn be related to a characteristic of the material to which it is applied to or embedded within, e.g. strain, temperature, hydrogen presence FIBRE ORIENTATION Fibre alignment in a non-woven or mat laminate where the majority of fibres are in the same direction, resulting in a higher strength in that direction FIBRE PATTERN 1 Visible fibres on the surface of laminates or mouldings. 2 The thread size and weave of glass cloth FIBRE PREFORMS A solely fibrous network of reinforcement fibres created by one or more weaving, knitting or braiding process to create a geometrical shape that is then subsequently infiltrated with a matrix phase (polymer, metal or ceramic) to create a three-dimensionally reinforced composite component. The preform is usually rigidised using a matrix-compatible binder before infiltration FIBRE REINFORCED METAL (MMCf) A metal alloy containing continuous reinforcement fibres or filaments; often silicon carbide or carbon FIBRE REINFORCED PLASTIC (FRP) A fibre-reinforced thermosetting or thermoplastic polymer matrix composite material FIBRE SURFACE TREATMENT Carbon fibres are usually given a post-graphitisation surface treatment by either a chemical or an electro-mechanical method. The surface treatment enhances the bond between the fibres and the resin matrix in the cured laminate. This enhanced bond improves the shear and compressive properties of the laminates, but if the surface treatment is over done brittle laminates can result FICK'S EQUATION Diffusion equation for moisture migration. This is analogous to Fourier's equation of heat conduction FILAMENT 1 For technical textiles: the smallest unit of a fibrous material. The basic unit formed by drawing and spinning 2 A continuous discrete fibre with an effective diameter in the range of: Carbon: 6 m to 10m Glass: 6 m to 13 m Aramid: >12m Alumina: >20 m Boron: 100m to 200 m Silicon carbide: 10m to 20 m or 100m to 140m, depending on the source Note: The cross-section is not necessarily circular FILAMENT REINFORCEMENT Composite material using filaments as the reinforcement phase, [See also: FILAMENT] FILAMENT WINDING Automated process of placing filaments or fibres onto a mandrel in prescribed patterns. The resin impregnation can be before or during the winding, known as prepreg or wet winding, respectively. The mandrel can subsequently be removed after curing of the composite material. Filament winding is most advantageous in building pressure vessels, pipes, drive shafts, or any device that is axisymmetrical FILAMENT WOUND An item manufactured using a filament winding process FILAMENT YARN For technical textiles: one or more continuous filaments, with or without twist FILL, FILLER Yarn oriented at right angles to the warp in a woven fabric. [See also: WEFT] FILLET A smooth concave build-up of material between two surfaces, e.g. a fillet of adhesive in a bonded joint; a fillet of weld metal between two plates, generally placed at an angle to each other; a fillet of solder between a component lead and a solder pad or terminal, a fillet of conformal coating material between a component and printed-circuit board FILM ADHESIVE A synthetic resin adhesive, usually of the thermosetting type in the form of a thin film of resin with or without a fibrous carrier or support. Note: Film adhesives usually have some tack to enable their placement during assembly FINISH Material and process used to treat fibres to improve the interfacial bond between fibre and matrix. (Definition specific to composites) FINISHING Final manufacturing processes which result in a component ready for assembly. Often used to describe minor machining or cleaning operations FIRST Far infra-red sub millimetre space telescope FIRST-PLY FAILURE The initial failure of a laminated or similar multi-layer composite material which can be predicted by an established criterion. Note: The structure can be capable of carrying additional loads after this initial failure, but this has to be substantiated by consideration of the appropriate failure models to establish the LAST-PLY FAILURE FITTING Fittings (or 'bosses') are responsible for inlet and outlet of the stored medium and for closing of the vessel at the polar openings. They are also often necessary as part of the mandrel in the manufacture of the vessel FLAGRO Fracture mechanics analysis software developed by NASA, [See also: ESACRACK, ESALOAD] FLAMMABILITY A measure of the ease with which a material is set on fire. FLAW A local discontinuity in a composite structure such as a scratch, notch, crack, void, delamination, or debonding. Note: some fracture models also define a notch as a flaw, e.g. WEK [See also: DEFECT] FLAW (CRITICAL) A flaw of sufficient size and shape to cause unstable growth to occur under the specific operating loads and environment FLAW (INITIAL) A flaw that exists in a composite structure before the application of operating loads and exposure to environment. (Specific definition in relation to composites) FLEECE For technical textiles: fibrous webs, e.g. felts, non-woven fabrics, wadding; produced from twisted single textile fibres FLEXURAL MODULUS The ratio, within the elastic limit, of the applied stress on a test specimen in flexure to the corresponding strain in the outermost fibres of the specimen. (Specific definition in relation to composites) FLEXURAL STRENGTH 1 The resistance of a material to breakage by bending stresses. 2 The strength of material in bending expressed as the tensile stress of the outermost fibres of a bent test sample at the instant of failure. (Specific definition in relation to composites) 3 The unit resistance to the maximum load before failure by bending. (Specific definition in relation to composites) FLIGHT MODEL The flight end item, which is subjected to formal functional and environmental acceptance testing, Ref.[1] FLIGHT SPARE The spare end item for flight, which is subjected to formal acceptance testing, Ref.[1] FLLI Fracture Limited Life Item FLLIL Fracture Limited Life Items List FLOCK For technical textiles: short chopped fibres FLOW The movement of resin under pressure, enabling all parts of a mould to be filled; flow or creep is the gradual but continuous distortion of a material under continued load, often at elevated temperatures FLTP Future launchers technologies programme; an ESA programme FLUX A material which, during welding, brazing or soldering, removes the oxide film, protects the surface from oxidation and permits the filler material to wet the surfaces to be joined FM Flight Model FMCW Frequency-modulated continuous wave. A fibre optic-based strain measurement system FMECA Failure mode effects and criticality analysis FML Fibre metal laminate. [See: ARALL, GLARE, CARE] FOD Foreign object impact damage FOLDED YARN For technical textiles: two or more single yarns twisted together Note: Folding is synonymous with plying FOOTPRINT The area of the nut, collar or tail of an installed mechanical fastener that is in contact with the substrate material; bearing surface FORCE 1 Mechanical load 2 The male half of a mould, which enters a cavity, exerting pressure on resin and causing it to flow (also called punch) 3 Either part of a compression mould (top force and bottom force) FOS Fibre optic sensor; smart technology FOTON Un-manned Russian research spacecraft with MIRKA re-entry capsule. [See also: MIRKA] FOURIER'S EQUATION Diffusion equation commonly associated with the heat conduction in a body. Fick's equation is a special case, applied to the migration and accumulation of moisture. [See also: FICK'S EQUATION] FP Fabry-Prot FPF See: FIRST-PLY FAILURE FRACTURE Rupture of the surface without complete separation of laminate FRACTURE CRITICAL ITEM A safe-life or fail-safe Potentially Fracture Critical Item (PFCI). [See also: PFCI] FRACTURE LIMITED LIFE ITEM Any item that requires periodic reinspection to comply with safe life or fail-safe requirements, [See: SAFE LIFE; FAIL-SAFE (structure)], Ref. [5] FRACTURE REGION A term used in the mechanical testing of MMC and CMC materials to describe reinforcement failure, normally continuous fibres or filaments FRACTURE TOUGHNESS The resistance of a material to fracture, a measure of the damage tolerance of a material containing initial flaws or cracks. The old term Toughness to describe the resistance of a material to permanent deformation was poorly defined and gave little basis for comparison between materials, particularly under representative service environments. For strong materials such as heat-treated steels, aluminium and titanium alloys: plane strain values of critical stress intensity factor KIC are valid material properties, independent of specimen thickness, to describe fracture toughness. Materials having appreciable plasticity before fracture are described by the J integral - the critical value of which is a material property in the same way that KIC is for a linear elastic solid, Ref.[2]. For metals, the Fracture Toughness is usually obtained by measuring the Strain Energy Release Rate of a pre-cracked Crack Opening Displacement (COD) specimen. For materials destined for corrosive service environments, testing can be carried out under representative conditions to give a KISCC value. [See also: CRITICAL STRESS INTENSITY, Ref. [5]] FRCI Fibrous Refractory Composite Insulation, e.g. Space Shuttle Orbiter FREE EXPANSION Thermal or moisture expansion without external stress FRF Frequency Response Function FRP Fibre-reinforced plastic FRS Fibre-reinforced superalloy FRSI Felt reusable surface insulation, TPS system, e.g. Space Shuttle Orbiter FS Flight spare FSE Flight Support Equipment FSS Frequency selective surface FULL SMART SYSTEM A system of sensors, interrogation and analysis software and compensators able to monitor and react in a required manner to external influence without human intervention FUNCTION ORIENTED MODEL Physical model dedicated to the qualification of particular functional requirements. It is flight representative as necessary for the limited qualification objectives, Ref.[1] FUNCTIONAL ANALYSIS Related to the verification of the correct implementation of a required function, Ref.[1] FUSION JOINING Joining techniques involving the melting of one or more joint constituent, e.g. welding, brazing, soldering. [See also: WELDING, BRAZING] FUSION WELDING Creating a joint where one or more of the joint parts is molten, [See also: WELDING] FV Flight Vehicle FWC Finite width correction factor G G1C Fracture energy GALVANIC CORROSION Corrosion that occurs in aqueous or humid conditions that is driven by electrochemical potential differences between two phases, usually metallic, in electrical contact. It can also occur for a single phase where a gradient environment exists; called crevice corrosion. [See: CREVICE CORROSION] GAM Groupe dActivation Moteur GARTEUR Group for Aeronautical Research and Technology in Europe GAT Groupe dActivation Tuyre GAUGE LENGTH Part of a test specimen in which the characteristics of the material are determined; often instrumented with strain gauges, extensometers GC Gas-chromatograph GCMC Glass-ceramic matrix composite GEL COAT A resin applied to the surface of a mould and gelled before lay-up. The gel coat becomes an integral part of the finished laminate and is usually used to improve surface appearance GEL POINT The stage at which a liquid begins to exhibit pseudo-elastic properties, also conveniently observed from the inflection point on a viscosity versus time plot Note: Also called GEL TIME GEL TIME The exposure period required at a prescribed temperature to convert the resin from a fluid to a defined partial-cure stage. Resin bleed during cure can only occur substantially before gelling GENERALISED HOOKE'S LAW The most general linear elastic stress-strain relation for an anisotropic material from which materials with various types of symmetries can be derived GEO Geostationary Earth orbit GEODESIC The shortest distance between two points on a curved surface GEODESIC ISOTENSOID Constant-stress level in any given filament at all points in its path GEODESIC OVALOID A contour for end domes, the fibres forming a geodesic line. The forces exerted by the filaments are proportioned to meet hoop and meridional stresses at any point GEODESIC-ISOTENSOID CONTOUR In filament-wound reinforced-plastic pressure vessels, a dome contour in which the filaments are placed on geodesic paths so that under pressure loading the filaments will exhibit uniform tension throughout their length GFRP Glass-fibre reinforced plastic Note: In this handbook G = glass, but in US publications G = graphite. [See also: CFRP] GH2 Gaseous hydrogen GIRL German Infrared Laboratory GLARE Glass fibre-reinforced aluminium laminate. [See: FIBRE METAL LAMINATE] GLASS CERAMIC MATRIX COMPOSITE (GCMC) Composite containing a mixture of glass and ceramic phase as a matrix for fibre reinforcement (often SiC or C fibres) GLASS FIBRE Reinforcement fibres of which E-, R- and S- grades are normally used in composites for aerospace applications. Note: E-glass: electrical grade; R and S: high strength grades GLASS FILAMENT Drawn from molten glass through platinum bushings. The most widely used filament in composite materials. Glass filament can be made into unidirectional plies, woven fabric, mats and short-fibre composites like the sheet moulding compound GLASS MATRIX COMPOSITE (GMC) A composite containing a glassy phase as a matrix for fibre reinforcement (often SiC or C fibres) GLASS TRANSITION TEMPERATURE (Tg) The temperature at which increased molecular mobility results in significant changes in the properties of a cured resin system GNC Guidance, Navigation and Control GOLD (Au) Metallic element, melting point 1064C, density 19300 kg m-3. Uses: alloying additions, coatings GOX Gaseous Oxygen GPL Groove proportional lock-bolt; a type of mechanical fastener GPR Ground Penetrating Radar GPS Global Positioning System GRADED STRUCTURE Material in which the chemical composition or microstructure varies with position. It can be achieved most readily by means of powder metallurgical techniques. In a product graded from pure material A to pure material B, intermediate A+B powder mixture stages can be used to smooth the transition. These materials can be used to reduce mismatch problems in physical, chemical and metallurgical properties, e.g. CTE mismatch GRAPHITE FIBRE A fibre made from a precursor by an oxidation, carbonisation and graphitisation process (which provides a graphitic structure). [See also: CARBON FIBRE] GREEN SHAPE Ceramic parts that are in an intermediate state of manufacture into a shape that is near that of the finished ceramic product. They exist after the initial consolidation of the blended powders but prior to the high pressure and/or temperature densification processes that give the desired final mechanical properties GRIST Grazing incidence solar telescope GRP Glass reinforced plastic; an industrial composite not a high-performance structural composite for aerospace applications; sometimes used for tabs on the ends of some composite test specimens GSE Ground Support Equipment GTO Geostationary Transfer Orbit H HAFNIUM (Hf) Metallic element, melting point 2231C, density 13310 kg.m-3. Uses: carbide former in superalloys, coating material compositions, including diffusion barrier coatings on tungsten reinforcing filaments HALIDE Compound formed with an element from Group VII of the periodic table of elements: fluoride, chloride, bromide HAND LAY-UP The process of placing (and working) successive plies of reinforcing material or resin-impregnated reinforcement in position on a mould by hand HARDENER 1 A substance or mixture added to a plastic composition to promote or control the curing action by taking part in it. 2 A substance added to control the degree of hardness of the cured film [See also: CATALYST] HARDWARE MATRIX The matrix identifying for each equipment the related qualification status and the required models, Ref.[1] HASTELLOY A nickel-based alloy HAWT Horizontal Axis Wind Turbine HAZ Heat Affected Zone HCF High-cycle Fatigue HE [See: HYDROGEN EMBRITTLEMENT] HEALTH MONITORING For smart technologies: a diagnostic system which can provide data on the integrity or functioning of structures or structural components, either continually or periodically HEAT TREATMENT Metal alloys: thermal conditioning of the material to achieve a desired metallurgical structure and/or properties. Also used to relieve residual stress after or between mechanical working. [See also: CONDITION] HEE [See: HYDROGEN EMBRITTLEMENT ENVIRONMENT] HEMISPHERICAL EMITTANCE (h) The total energy emitted over a hemisphere above the emitting element for all wavelengths, Ref. [10] HEO Highly Elliptical Orbits HERMES Manned winged reusable spacecraft; European programme HETEROGENEITY 1 Microscopic level: local variation of constituent materials. 2 Macroscopic level: ply-by-ply variation of materials or orientations HFE Human Factor Engineering HHPV Hydraulic high pressure vessel HiBi Highly birefringent. A type of optical fibre used in fibre optic sensor (FOS) smart technologies HIGH CYCLE FATIGUE (HCF) Repeated mechanical loading applying low to moderate stresses for a high number of cycles, typically 106 to 108 or greater HIGH MODULUS CARBON FIBRES (HM) A range of carbon fibres which have a tensile moduli greater than 310 GPa, typically HIGH-PRESSURE LIQUID CHROMATOGRAPHY (HPLC) HPLC is an analytical technique for determining the chemical constituents of the prepreg matrix. By testing a batch of prepreg it is possible to take the results and a reference trace (form of fingerprint) for the same prepreg to provide a means of comparison on product consistency HIGH STRENGTH CARBON FIBRES (HS) A range of carbon fibres which have tensile strengths up to 3500 MPa and tensile moduli in the range of 200 GPa to 255 GPa, typically HIGH TENACITY CARBON FIBRES (HT) A range of carbon fibres which includes HS high strength fibres and VHS very high strength fibres HIT RATE For structural health monitoring or nondestructive testing: the number of acoustic emission events detected in a given time period, [See also: ACOUSTIC EMISSION] HKM 1650 Fibrous insulation material HM High modulus; a range of carbon fibres that also includes UHM ultra high modulus fibres HOCOSC Hot-to-cold structure combination HOMOGENEITY Material uniformity within a body. In the mechanics of composite materials, micro- and macroscopic homogeneity are achieved by smearing the actual heterogeneity HONEYCOMB Manufactured product of resin-impregnated sheet material (paper, glass or aramid-based fabric) or sheet metal formed into hexagonal-shaped cells; used as a core material in sandwich construction HOOKE [See: GENERALISED HOOKE'S LAW] HOOKEAN [See: GENERALISED HOOKE'S LAW] HOOP STRENGTH The circumferential strength of a material of cylindrical form subjected to internal or external pressure HOOP STRESS The circumferential stress in a material of cylindrical form subjected to internal or external pressure HOOP WINDING The placing of fibres (filament) perpendicular to the longitudinal axis of a cylinder or a pressure vessel HOPE H-II Orbiting Plane. Winged man-capable re-entry glider. Japanese programme HOPE-X H-II Orbiting Plane Experimental. Full scale, unmanned prototype of the HOPE winged man-capable re-entry glider. Japanese programme HORUS Upper spaceplane stage of SNGER HOT ISOSTATIC PRESSING (HIP) A consolidation technique consisting of simultaneous high temperature and very high inert gas pressure. Often used as a stage in a powder metallurgical process. Can also be used to eliminate porosity from cast materials HOT PRESSING Manufacturing method often used for metal and ceramic powder matrices, but also for pre-impregnated fibre tapes with glass matrices. Effective for closing porosity HOTOL Horizontal take-off and landing HPLC [See: HIGH PRESSURE LIQUID CHROMATOGRAPHY] HPV High pressure vessel HRE Hypersonic Research Engine (USA) HRSI High-temperature Reusable Surface Insulation, e.g. Space Shuttle Orbiter HS High strength; a range of carbon fibres HST High speed wind tunnel HSTS High stability telescope structures HUYGENS An ESA-built probe for decent onto Titan, the largest Saturn moon. Part of the NASA Cassini mission to study Saturn, it's rings and moons. [See also: CASSINI-HUYGENS] HT High tenacity (high strength/high strain); a range of carbon fibres which includes HS high strength fibres and VHS very high strength fibres; also known as high tension HTI High temperature insulation HTP Hot thermal protection HYBRID 1 Composite: containing more than two constituents, e.g. a graphite/glass/epoxy hybrid; an intralaminar hybrid has hybrid plies made from graphite and glass filaments; an interlaminar hybrid has laminates made from two or more different ply materials 2 Reinforcing fibre: a mixture of two or more types of fibres, e.g. high strength carbon and high modulus carbon, carbon and aramid 3 Fabric: made of more than one type of fibre, e.g. usually combinations of carbon, glass and aramid fibres 4 Co-mingled: a mixture of reinforcing fibre and thermoplastic fibre in a fibre tow 5 Tank: where a tank thrust structure is enclosed within an aeroshell; a reusable launch vehicle concept 6 FML: a fibre metal laminate containing both composite layers and sheet metal HYBRID PHILOSOPHY Model philosophy representing a compromise between prototype and protoflight approaches. It is based on a protoflight model on which a partial protoflight qualification test campaign is carried out. Specific qualification tests in the critical areas are carried out on dedicated models. The hybrid model philosophy is used in projects where advanced qualification activities must be performed in areas of new design or having a critical impact on the verification program, Ref.[1]. [See also: PROTOFLIGHT MODEL] HYBRID POLYMER COMPOSITE [See: FIBRE METAL LAMINATE (FML)] HYDROGEN EMBRITTLEMENT (HE) The degradation of a material's ductility and fracture characteristics when exposed to hydrogen at temperatures up to 600C, typically. Material sensitivity depends on the composition and the ease of hydrogen transport from the environment, e.g. hydrogen charging. Effects can be catastrophic HYDROGEN EMBRITTLEMENT ENVIRONMENT (HEE) Degradation of a material's ductility and fracture characteristics when exposed to hydrogen but without sufficient time to charge the material with hydrogen. Effects can be additional to those described as HE HYDROLYTIC Chemical reaction of a substance with water HYFLEX Hypersonic Flight Experiment HYGROSCOPIC Tending to absorb moisture from the air HYGROTHERMAL The combination of moisture and temperature HYGROTHERMAL EFFECT Change in properties due to moisture absorption and temperature change H/W Hardware I IBC Individual blade control. A smart technology proposed for helicopter rotor blades IC Integrated circuit ICD Interface Control Document ICI Imperial Chemical Industries, UK ICMCf Inorganic ceramic matrix composite with fibrous reinforcement ICSTM Imperial College of Science, Technology and Medicine, UK I/F Interface IFBG In-fibre Bragg grating, [See also: BRAGG GRATING] IFI Internal Flexible Insulation; a thermal protection system (TPS) IITRI Illinois Institute of Technology Research Institute, USA; a type of mechanical test ILSS Interlaminar shear strength IM 1 Intermediate modulus; a range of carbon fibres that have tensile moduli in the range of 255 GPa to 310 GPa, typically 2 Integration Model IMC Intermetallic matrix composite IMI 1 Internal Multiscreen Insulation; a thermal protection system (TPS) 2 Imperial Metal Industries; commonly used alloy designation for titanium-based materials IMIDE A family of polymers, including polyimide (PI) and bismaleimide (BMI); used in a resin form as a matrix for high-performance reinforced plastics IMPACT DAMAGE A structural anomaly created by the impact of a foreign object IMPREGNATE In reinforced plastics, to saturate the reinforcement with a resin IMQ Initial material quality. A distribution of microstructural anomalies that might lead to failure INCONEL A range of nickel-based alloys INCREMENTAL FORMING A process for shaping thermoplastic-based composites INFILTRATION Part of composite manufacturing method where the matrix phase (metal, ceramic, glass) is incorporated with the reinforcement. Matrix phase can be in a liquid or gaseous form, e.g. ceramic or glass slurry, molten metal, or silicon carbide rich gas. Note: The infiltration stage is often repeated, [See also: PYROLYSIS] IN-HOUSE A process or test standard created and used within a particular organisation; often considered as confidential and so not disclosed to other parties INITIAL CRACK SIZE The maximum crack size, as defined by non-destructive inspection, that is assumed to exist for the purpose of performing a fracture mechanics evaluation, Ref. [5] INITIAL FLAW A flaw that exists in a composite structure before the application of operating loads and exposure to environment. (Specific definition in relation to composites) INITIAL MATERIAL QUALITY (IMQ) The distribution of microstructural anomalies that might lead to failure. Term used in the damage tolerance of advanced composite materials in quantifying the effect of defects below the current NDE detection capability INITIAL MODULUS [See: MODULUS (of elasticity)] INORGANIC COMPOSITE Composite not containing organic polymers INSERT 1 An integral part of a plastic moulding, consisting of metal or other material which can be moulded into position or pressed into the moulding after the moulding is complete. 2 A fixation device or type of fastener system, commonly used in sandwich panels IN-SITU FIBRE STRENGTH The strength of a fibre reinforcement when incorporated into a composite after manufacture. For high-temperature processing methods, the initial fibre strength can be seriously affected by the processing time and temperature, or by chemical reaction with the matrix phase, e.g. molten metals IN-SITU OXIDISATION Composite manufacture: methods for producing ceramic (oxide) matrix composites from a metal matrix composites with molten matrix phase. Usually applied to aluminium MMC, of which the LANXIDE PROCESS is a proprietary method IN-SITU SILICONISING Processing technique involving infiltration of molten silicon into porous C-C composite and subsequent firing to produce a SiC matrix phase INSPECTION PROCEDURE This document lists all the requirements to be verified by Inspection, grouping them in categories detailing the Verification Plan activity sheets, with planning of the execution and a definition of the associated procedures, Ref.[1] INSPECTION REPORT This document describes each verification activity performed when inspecting hardware during manufacturing/integration and contains proper evidence that the relevant requirements are satisfied and the indication of any deviation, Ref.[1] INSPECTION A verification method for physical characteristics that determines compliance with requirement without the use of special laboratory equipment, procedures, items or services. Inspection makes use of standard methods to verify requirements for construction features, document and drawing compliance, workmanship, physical conditions, Ref.[1] INTEGRATED SUBSYSTEM TEST (ISST) A performance and functional test having the scope to verify the correct functioning of the integrated subsystem in terms of operating modes, with a particular emphasis on subsystem to subsystem interface verification, Ref.[1] INTEGRATED SYSTEM CHECK (ISC) A sub-set of the Integrated System Test (IST), able to involve all major functions, at the maximum extent automatically performed. It has the scope to provide the criteria for judging successful survival of the system/element in a given test environment, with a reasonably high degree of confidence, in a relatively short time, Ref.[1]. [See also: INTEGRATED SYSTEM TEST] INTEGRATED SYSTEM TEST (IST) It has the scope to verify that performance of the system/element meets the specification requirements, in terms of correct operation in all operational modes, including back-up modes and all foreseen transients, Ref.[1]. [See also: INTEGRATED SYSTEM CHECK] INTEGRATION MODEL Physical model functionally representative of the flight end items in terms of electronic and software, used for functional and interface tests and for failure mode investigations. Commercial parts are utilised, but they must be procured from the same manufacturer of the Hi-rel parts to be used in the flight end item, Ref.[1] INTEGRATION PROCEDURE This document provides detailed step-by-step instructions to the integration teams for conducting the integration activities in agreement with the Integration Specification requirements, Ref.[1]. [See also: INTEGRATION SPECIFICATION] INTEGRATION REPORT This document describes integration performance, results and conclusions in the light of the integration requirements, Ref.[1] INTEGRATION SPECIFICATION This document is prepared for each major integration activity described in the Verification Plan task sheets with the objective to detail the integration requirements INTEGRATION The process of assembling and testing hardware and software to obtain a particular configuration. The integration encompasses the verification of the interface compatibility and of the operation of the mated hardware and software to demonstrate the overall end-to-end performance and to ensure that all interfaces meet the specified requirements, Ref.[1] INTEGRITY CONTROL A series of actions undertaken to demonstrate the structural integrity of a design. This will take due account of operational conditions and design loads, in conjunction with defined damage tolerance and safety requirements INTERACTION Same as coupling. For example, longitudinal tensile strength is affected by the presence of transverse stress. Similar interaction exists between the longitudinal buckling stress and the transverse or shear stress. As a rule, the interaction effects for composite materials are greater than for the conventional isotropic material. All anticipated stresses are considered simultaneously INTERFACE Composite materials: Boundary or transition zone between constituent materials, such as the fibre-matrix interface, or the boundary between plies of a laminate. Debond at the microscopic or fibre-matrix interface can lead to fibre breakage and matrix cracking. Debond at the macroscopic or interlaminar interface can lead to delamination INTERFEROMETER A device where light from a source is split into two or more beams, which are subsequently reunited after travelling over different paths and interfere. Note: Several versions exist for interrogation of FIBRE OPTIC signals INTERLAMINAR SHEAR STRENGTH (ILSS) The shear strength existing between layers of a laminated material INTERLAMINAR STRESSES The stress between two or more adjacent plies in a laminated composite structure; three stress components associated with the thickness direction of a plate. The remaining three are the in-plane components of the plate. Interlaminar stresses are significant only if the thickness is greater than 10% of the length or width of the plate. These stresses can also be significant in areas of concentrated loads, and abrupt change in material and geometry. The effects of these stresses are not easy to assess because three-dimensional stress analysis and failure criteria are not well understood INTERLAYER A material C, placed between two materials A and B which are to be joined, to reduce physical or chemical incompatibilities between A and B. Often used in diffusion-bonded joints. Interlayers are generally very thin shims INTERMEDIATE MODULUS CARBON FIBRES (IM) A range of carbon fibres with tensile moduli in the range of 255 GPa to 310 GPa, typically INTERMETALLIC COMPOUND Stoichometric chemical compound formed between two or more metallic elements INTERMETALLIC MATRIX COMPOSITE (IMC) Composite using an intermetallic compound as the matrix material. [See also: ALUMINIDE] INTESPACE Test centre, France INTRALAMINAR STRESSES The stresses in the plane of a ply INVAR A nickel-based alloy INVARIANT Constant values for all orientations of the co-ordinate axes. Components of stress, strain, stiffness and compliance all have linear and quadratic invariants. For composite materials, they represent directionally independent properties and the bounds of stiffness and strength of multidirectional laminates INVESTMENT CASTING A casting method designed to achieve high dimensional accuracy, usually for small components. Moulds are joint free. Established production technique for high-temperature metal alloys, e.g. aero engine parts. Variant process: lost-wax casting IONISABLE CONTAMINANT Process residues, such as flux activators, fingerprints, etching and plating salts, that exist as ions and when dissolved, increase electrical conductivity IOSIPESCU A test method using a double V-notched specimen; developed by the University of Wyoming IP TML In-phase thermo-mechanical fatigue IR Infra Red IRAS Infra-red astronomical satellite IRIDIUM Metallic element, melting point 1538C, density 7310 kg m-3. Uses: electronics and coatings IRIS Italian Research Interim Stage IRON (Fe) Metallic element, melting point 156.63C, density 7870 kg m-3. Uses: base element for steels, iron-based superalloys, alloying additions IRRADIATION The bombardment of a composite material with a variety of subatomic particles, usually alpha-, beta- or gamma-rays, to bring about changes in the material's physical and mechanical properties ISAS Institute of Space and Astronautical Science; Japan's national space research centre ISC Integrated system check ISO International standards organization ISOTROPIC Property that is not directionally dependent. [Having the same physical or mechanical properties in all material directions]. Metals are often assumed to be isotropic. This is normally not the case, but they do generally show considerably less anisotropy than fibre-reinforced composites ISOTROPY [See: ISOTROPIC] ISS 1 International space station 2 Internal stress superplasticity ISST Integrated subsystem test IST Integrated system test ITE Integral throat and entrance; Rocket nozzles ITEC Integral throat exit cone; Rocket nozzles ITEM The lowest subdivision of a subassembly in which each item is a separate and distinct element not normally separated into further subdivisions or disassembly without destruction of designed use ITO Indium tin oxide IUS Inertial upper stage J JIG A fixture or tool that retains a material, sample or structure, e.g. for testing or during processing; also known as rig JIS Japanese Institute of Standards JOINT 1 General: Any element that connects other structural elements and transfers loads from one to the other across a connection, Ref. [5]. 2 Bonded: The location at which two adherends are held together with a layer of adhesive; the general area of contact for a bonded structure. Common bonded types are: - Butt Joint: The edge faces of the two adherends are at right angles to the other faces of the adherends. - Scarf Joint: A joint made by cutting away similar angular segments of two adherends and bonding them with the cut areas fitted together. - Lap Joint: A joint made by placing one adherend partly over another and bonding together the overlapped portions JOINT EFFICIENCY Parachutes: the strength of a stitched joint as a percentage of that of the bulk broadloom fabric JOINT STRUCTURE Pressure vessels have to be connected to the surrounding main structure. This is performed by a joint structure. A cylindrical joint structure (or 'skirt') is used to attach isotensoid-shaped vessels in their cylindrical area. Brackets are used to attach spherical vessels at the poles. These joint structures have to be so designed as to respect all load cases K K Karlak K49 Kevlar"! 49 KDF Knock-down factor KEVLAR( A grade of aramid fibre from E.I. Du Pont de Nemours [See also: ARAMID] KFRP Kevlar-fibre reinforced plastic KIC Plane strain fracture toughness, [See also: CRITICAL STRESS INTENSITY FACTOR; FRACTURE TOUGHNESS] KINK A distortion in the direction of the reinforcing fibres within a prepreg; often a localised effect but can be considered as a defect KISCC Threshold stress-intensity factor for stress-corrosion cracking. The maximum value of the stress-intensity factor for a given material at which no environmentally induced crack growth occurs at sustained load for the specified environment, Ref.[5]. [See also: FRACTURE TOUGHNESS] (Kth or Kth Threshold stress-intensity factor for dynamic loading. The stress-intensity range below which crack growth will not occur under cyclic loading L L2K Plasma arc wind tunnel test LACIS Large area composite inspection system LAM Liquid Apogee Motor LAMINA [See: PLY] LAMINA-LEVEL MATERIAL PROPERTIES Established from test data for a single-ply or multi-ply, single-direction-oriented lamina lay-up LAMINATE FAMILY Laminates sharing the same ply number and angles LAMINATE Plate consisting of layers of uni- or multidirectional plies of one or more composite materials LAMINATED PLATE MODEL Mathematical model derived to describe behaviour of anisotropic materials of laminar construction, best suited to continuous fibre composites with unidirectional plies LAMINATED-PLATE THEORY The most common method for the analysis and design of composite laminates. Each ply or ply group is treated as a quasi-homogeneous material. Linear strain across the thickness is assumed. Note: Also called the lamination theory LAMINATE-LEVEL DESIGN ALLOWABLE Established from multiply laminate test data or from test data at the lamina level and then confirmed at the laminate level by test-validated analytical methods. [See also: ALLOWABLES, DESIGN VALUES] LAMINATE-LEVEL DESIGN VALUE [See: LAMINATE-LEVEL DESIGN ALLOWABLE] LANXIDE A ceramic composite consisting of an aluminium oxide network with pores filled with aluminium (Lanxide Corp.) LAP In filament winding, the amount of overlay between successive windings, usually intended to minimise gapping LAP JOINT Joining or fusing of two overlapping surfaces, [See: JOINT] LaRC or LARC 1 NASA Langley Research Center, USA. 2 A polyimide resin developed by NASA Langley Research Center, USA LAS Lithium-Alumino-Silicate. A family of glass-ceramic matrix materials with different levels of ZrO2 and BaO LAST PLY FAILURE The failure of the ply or ply group in a multidirectional laminate that occurs at last. The load corresponding to this failure can be the ultimate load LAYER [See: PLY] LAY-UP 1 Hand- or machine-operated process of ply-by-ply laying of a multidirectional laminate. 2 Ply-stacking sequence or ply orientations of a laminate LAW OF MIXTURES An externally applied strain (in tension, compression or shear) is equal to the strains in all the phases present, i.e. reinforcement and matrix. The contribution of each phase is therefore directly dependent on its volume fraction within the composite. Note: This relies on all phases being elastic. For MMC and CMC materials: It can predict stiffness values of but only to very low strain levels. For unidirectional composites: It can provide reasonably accurate tensile strength values, provided that fibre degradation has not occurred. For multidirectional MMC and CMC materials: it is inappropriate and predicts high, inaccurate strength values LBB Leak Before Burst; pressure vessels LBU Laser-based ultrasonics LCCD Linear charge cord device LCF Low-cycle Fatigue LCP Liquid crystal polymer LDEF Long Duration Exposure Facility LDR Large deployable reflector LDV Laser Doppler vibrometer LEAD (Pb) Metallic element, melting point 328C, density 11350 kg m-3. Uses: alloying additions LEAK BEFORE BURST Fracture mechanics design concept in which it is shown that any initial defect grows through the wall of a pressurized system and cause leakage prior to burst (catastrophic failure) at maximum design pressure (MDP), [See: MAXIMUM DESIGN PRESSURE (MDP)], Ref. [5] LEFM Linear elastic fracture mechanics LEO Low Earth Orbit LH Liquid hydrogen LH2 Liquid Hydrogen LID Liquid-interface-diffusion (NASA): a technique for joining dimpled metal foils in Multiwall thermal protection systems LIDAR Light detection and ranging: This operates on the same principles as RADAR but uses light instead of radio frequencies. The transmitted light interacts with, and is changed by, the target. Some of this light is reflected or scattered back to the instrument where it is analysed. The change in the properties of the light enables some property of the target to be determined. The time for the light to travel out to the target and back to the lidar can be used to determine the range. Differential absorption lidar (DIAL) uses two different laser frequencies to provide atmospheric chemical composition information LIGHT ALLOY General term for metal alloys of low density, e.g. aluminium, magnesium, which usually have high specific strengths (ratio of strength to density) LIMIT LOAD [See: LOADS] LIMIT LOAD OR STRESS The maximum load or stress assumed to act on a structure in the expected operating environments, Ref. [5]; [See also: LOADS] LIMIT STRESS [See: LIMIT LOAD] LINEAR ELASTIC FRACTURE MECHANICS (LEFM) Engineering principle to describe the propagation of a single crack through a material, usually a metal alloy, in which it is assumed that all the material is behaving elastically LINER In a filament-wound pressure vessel, this is the continuous, usually flexible, coating on the inside surface of the vessel used to protect the laminate from chemical attack or to prevent leakage. The evaluation of the material for the liner depends on the stored medium and the pressure level. For lower-pressure application, a rubber liner can be sufficient. For high-pressure application, a steel or titanium load-carrying liner is necessary LIQUID METAL PRESSURE FORMING [See: LIQUID PRESSURE FORMING] LIQUID PHASE PROCESSING Usually applied to joining techniques where one or more of the constituent parts are melted during the processing, e.g. welding, brazing LIQUID PRESSURE FORMING Types of melt infiltration techniques for MMC production conducted in a pressure vessel. A development of low-pressure die casting LITHIUM (Li) Metallic element, melting point 181C, density 534 kg.m-3. Uses: aluminium-lithium alloys LLD Launch locking devices; part of SILEX LLV Lockheed launcher vehicle LOADING EVENT A condition, phenomenon, environment or mission phase to which the payload is exposed and which induces loads in the payload structure, Ref. [5] LOADING PATH Locus of increasing load in stress or strain space LOAD SPECTRUM (HISTORY) A representation of the cumulative static and dynamic loadings anticipated for a structural element during its service life, Ref. [5] LOADS Strength requirements are specified in terms of: Limit Loads: The maximum external loads to be expected during operational use. Ultimate Loads: Limit loads multiplied by prescribed FACTORS OF SAFETY, e.g. the ultimate loads are often established by applying a factor of safety of 1.5 on limit loads LOAD-STRAIN CURVE A graphical representation of the extension of a material under an applied load LONGITUDINAL MODULUS Elastic constant along the fibre direction in a unidirectional composite, [See also: YOUNG'S and SHEAR MODULUS] LOSS FACTOR ( Damping: a well established fundamental ratio with which to assess damping on a relative energy basis LOSS FACTOR (tan SYMBOL 100 \f "Symbol") Electrical: a power factor, values usually quoted at a particular frequency LOSS MODULUS A damping term describing the dissipation of energy into heat when a material is deformed LOW CYCLE FATIGUE (LCF) Repeated mechanical loading, applying high stresses for a low number of cycles, typically 104 to 106 LOW-STRAINED STRUCTURE A composite structural component which is designed to a reduced strain level so that catastrophic failure will not occur even in the presence of flaws or damage LOX Liquid Oxygen LPARL Lockheed Palo Alto Research Laboratory, USA LPI 1 Liquid-phase infiltration 2 Low pressure infiltration. Processes for manufacturing ceramic matrix composites, developed by  HYPERLINK "http://www.man-technologie.de/" MAN Technologie (D) LPI-C/SiC Carbon-silicon carbide composite, produced by LPI process by  HYPERLINK "http://www.man-technologie.de/" MAN Technologie, (D) LPF [See: LIQUID PRESSURE FORMING] LRR Launch Readiness Review LRSI Low-temperature Reusable Surface Insulation, e.g. Space Shuttle Orbiter LST Large space telescope LTM Low temperature moulding; a class of prepreg LTPP Long Term Space Transportation Systems Preparatory Programme; an ESA program LUIS Laser ultrasonic inspection system LVDT Linear variable differential transformers. A type of displacement sensor LWT Light-weight tank. The Space Shuttle external main fuel tank; superseded by SLWT super light-weight tank M MA Mechanically alloyed; a powder metallurgy technique for producing a dispersion of particles within an alloy MACHINING The removal of material in a controlled manner by one or more mechanical, electrical or chemical methods, e.g. turning, milling, drilling, electro-chemical discharge, ultrasonic, Ref. [10] MACROMECHANICS The study of structural behaviour of composite laminates using the laminated plate theory. The fibre and matrix within each ply are smeared and no longer identifiable MAGE Moteur dapoge gostationnaire europenne MAGNESIUM (Mg) Metallic element, melting point 650C, density 1740 kg.m-3. Uses: lightweight wrought and cast magnesium alloys; cast alloys can be composite matrices; alloying addition to other base systems MAGNETOSTRICTIVE A solid material which mechanically deformations when subjected to a magnetic field MANDREL The core around which impregnated paper, fabric, or resin-impregnated fibre is wound to form pipes, tubes, or vessels MANGANESE (Mn) Metallic element, melting point 1246C, density 7210 kg m-3. Uses: alloying additions MAN-MT Part of the German MAN Technologie company MARGIN OF SAFETY Ratio of excess strength to the required (calculated) strength MARSNET Multiple-lander ESA Mars mission MAS Magnesium aluminosilicate. A glass ceramic matrix Note: Variant containing higher levels of BaO is called BMAS MASS FRACTION [See: WEIGHT FRACTION] MAT 1 A fibrous material for reinforced plastic consisting of randomly oriented chopped filaments or swirled filaments with a binder, available in various widths, weights, and lengths 2 For technical textiles: fibrous material consisting of randomly oriented chopped filaments, short fibres or swirled filaments, loosely held together with a binder MATERIAL A raw or semi-finished product or compound (gaseous, liquid, solid) of specific characteristics, which is processed to form a part or a finished product, Ref. [6] MATERIAL DESIGN ALLOWABLE A material property that has been determined from test data on a probability basis and has been chosen to assure a high degree of confidence in the integrity of the completed structure, Ref. [9] MATERIAL IDENTIFICATION CARD (MIC) Accompanies a material sample supplied to ESA or any test house. It states all required information about the material batch MATERIAL REVIEW BOARD This board has the responsibility to process, in line with the applicable Product Assurance requirements, all Non-conformance Reports arising during verification activities MATHEMATICAL MODELLING Analytical verification based on mathematical modelling of the system. Modelling is performed on the basis of known mathematical techniques, providing a representation of the system features under investigation, Ref.[1] MATRIX 1 A material that binds a reinforcement, e.g. thermoplastic or thermosetting resin in fibre- reinforced composites, metal alloy in MMCs, Ref. [10]. Note: The most common matrices for organic composites are polyester, epoxy and polyimide; for metal-matrix composites, aluminium 2 Mathematical entity, consisting of rows and columns of numbers. In two dimensions, stress and strain are 1 x 3 matrices; and stiffness and compliance, 3 x 3 matrices MATRIX-CONTROLLED A laminate lay-up where the properties are largely determined by those of the matrix, e.g. +45-45 MATRIX FAILURE Gradual accumulation of fatigue crack or other damage distributed only within the matrix phase and without causing fibre damage. Applicable to MMC, C-C and CMC materials MATRIX INVERSION Algebraic operation to obtain compliance matrix from stiffness matrix, or vice versa. It is analogous to obtaining the reciprocal of a number MATRIX TRANSFER MOULDING Manufacturing method used for glass or glass-ceramic composites where molten matrix is added to a mould containing reinforcement fibres. Usually restricted to matrix materials with moderate melting temperatures, e.g. not ceramics. Detrimental fibre/matrix reactions can occur as a result of the high process temperatures MAUS Mobile automated ultrasonic scanner MAXIMUM DESIGN PRESSURE (MDP) For a pressurized system, maximum design pressure is the highest possible pressure occurring from maximum relief pressure, maximum regulator pressure, maximum temperature or transient pressure excursions. Factors of safety apply to MDP, Ref. [5] MAXIMUM STRAIN Failure criterion based on the maximum strains MAXIMUM STRESS Failure criterion based on the maximum stresses MBB Ottobrunn Part of the German MBB aerospace organisation MBSA Main body structural assembly; part of the Mars Observer Camera MCrAlY A range of corrosion-resistant coating alloys, where M can be nickel, cobalt or a combination of both MD Multidirectional MDA Methylene dianiline amine; a known carcinogenic substance used in some polyimide resin formulations, e.g. PMR-15 MDP Maximum Design Pressure [Pressure systems, including pressure vessels] MDSSC McDonnell Douglas Space Systems Co., USA MEASURAND A characteristic or property to be measured MECHANICAL ALLOYING A processing method originally invented to manufacture oxide dispersion strengthened nickel alloys. A high energy ball milling process, where alloying is the result of repeated fracture and cold welding of the component particles. The process can also induce chemical reactions, [See also: ODS ALLOYS] MECHANICAL LOAD Mechanically applied load, distinguished from cure or environment-induced load MECHANICAL PART Piece of hardware which is not electrical, electronic or electromechanical, and which performs a simple (elementary) function or part of a function in such a way that it can be evaluated as a whole against expected performance requirements and cannot be disassembled without destroying this capability, Ref. [6] MELT INFILTRATION Processing methods for incorporating a matrix phase with the reinforcement by means of capillary action. It can be assisted by positive pressure or vacuum MELT REFINING Technique proposed for manufacture of graded materials or structures, where a narrow molten zone is moved through the material to modify the microstructure, often by segregation mechanisms. Also known as ZONE REFINING MELT SPINNING A fibre-forming polymer is melted for extrusion through spinnerets and then directly solidified by cooling. Nylon and polyester fibres are produced in this way MELT STIRRING Process for forming and distributing oxide particles in molten metal alloys. Some variants use ultrasonic agitation of the melt MEMORY ALLOY A class of metal alloy which, after deformation whilst in one metallurgical state, regains its original shape after heating or cooling through a specific temperature. Also known as 'Shape Memory' effect, Ref. [10] MEMS Micro electro-mechanical systems MEOP Maximum expected operating pressure; pressure vessels METAL FIBRES A range of speciality fibres ranging in diameter from 2 *m to 80 *m, typically, that can be co-woven with carbon fibres for inclusion in a composite for certain applications, e.g. stainless steel, Inconel, Hastelloy, titanium. METALLIZED FIBRES A range of speciality fibres that are coated with a fine metallic layer, primarily to enhance electrical properties in composites METAL MATRIX COMPOSITE (MMC) Composite material in which the matrix is a metal alloy METCAN Metal Matrix Composite Analyser (Laminated plate model for fibre-reinforced metals) Mf Martensite finish temperature MFG Manufacturing MGSE Mechanical Ground Support Equipment METHOD OF MIXTURES also known as Law of Mixtures, [See: LAW OF MIXTURES] MIC Material identification card MICRO-ALLOYING Alloying additions in the low atomic percent levels, e.g. boron additions to aluminides, to modify mechanical properties. Often to increase ductility over base alloy system. Also known as DOPING MICROCRACKING 1 Cracks formed in composites when thermally created stresses locally exceed the strength of the matrix. (The effect is complex and can be associated with a combination of residual curing stress and stresses induced by thermal cycling.) 2 Progressive effect where the matrix phase in a composite material forms a network of small cracks, when residual stresses in the matrix exceed the strength of the matrix or that of the matrix-to-fibre interface; occurs mainly during cooling of a component after cure and is caused by the differential contraction between the high positive CTE of the matrix and the low, negative axial fibre CTE. Also occurs in service where thermal cycling or low temperatures can instigate and promote microcracking MICROMECHANICS Calculation of the effective ply properties as functions of the fibre and matrix properties. Some numerical approaches also provide the stress and strain with each constituent and those at the interface MICROMETEORIOD Debris accumulated in space from natural sources, e.g. comets, asteroids, the moon and planets MICROSENSOR Small devices (micro-technology) produced by micro-machining of Silicon. (Extension of IC technology.) They are capable of being embedded or bonded to a structure or mechanism without altering the overall characteristics of the host component, and can monitor conditions such as pressure, vibration acceleration MICROSTRUCTURE The structure of a material as seen with a microscope. Used normally to describe the grain structure, form and any other features which determine or influence the material behaviour MICRO-YIELD An applied force to produce a residual strain of 1x10-6 m/m along the tensile or compression loading direction, Ref. [9] MID-PLANE Centre of a laminate; usually the z = 0 plane MIG Metal Inert Gas; a fusion welding process MIP Mandatory Inspection Point MIRKA Mikro Rckkehr Kapsel MISP Mismatch induced superplasticity MIXTURE A fibre tow that contains both reinforcement fibres and polymer filaments, [See: COMINGLED] ML Mar and Lin; a fracture model MLI Multi-layer insulation, e.g. that used in the gloves of extra-vehicular activity space suits MMC Metal Matrix Composite MMCf Metal Matrix Composite, where the reinforcement phase is fibrous MMCp Metal Matrix Composite, where the reinforcement phase is particulate MMH Mono-methyl-hydrazine. A constituent of certain bipropellant rocket fuels, [See also: NTO] MMU Manned manoeuvring unit MOC Mars Observer Camera MOCK-UP Physical model used in support of design definition for overall architecture analyses, configuration design and assessment, interface control and definition, human factors assessment, operational procedures evaluation, layout optimisation, Ref.[1] Mod-EIT Modified Electrical Impedance Tomography MODEL PHILOSOPHY Definition of the optimum number of physical models required to achieve a high confidence in the product verification with the shortest planning and a suitable weighting of costs and risks, Ref.[1] MODULE It can be made up of directly functionally related equipment or of equipment from various subsystems. A module can be a flight element or can be a major portion of a flight element, e.g. Service Module, Payload Module. Note: Verification level typical of US standard, Ref.[1] MODULUS An elastic constant defined as the ratio between the applied stress and the related deformation, such as Young's modulus, shear modulus, or stiffness moduli in general MODULUS MISMATCH The difference in stiffness between a fibre and a matrix, or coating and substrate MOI Momentum of Inertia MOISTURE ABSORPTION Moisture absorption causes the properties of epoxy to change; it can be detrimental in causing the glassy temperature of the epoxy to be suppressed, and beneficial by counteracting swelling during stresses MOISTURE CONTENT The amount of moisture in a material determined under prescribed conditions and usually expressed as a percentage of the mass of the moist specimen, i.e. the mass of the dry substance plus the moisture present MOISTURE DISTRIBUTION Transient moisture profile changes very slowly with time. For temperature, a steady-state distribution can be attained in a short time. But for moisture concentration, only the first few plies from the exposed surface can change significantly with time. For the interior plies, months if not years elapse before a change takes place. This non-uniform distribution is considered in the assessment of the effect of moisture on the properties of composite materials MOISTURISED Samples, materials and structures that have been subjected to moisture, usually as a conditioning process prior to testing MOLECULAR COMPOSITE A combination of two molecular polymer groups where one is a rigid phase that provides a reinforcing effect in the other, flexible, phase MOLYBDENUM (Mo) Refractory metallic element, melting point 2623C, density 10220 kg.m-3. Uses: alloying additions MONITORING For smart technologies: a diagnostic system which can provide data on the integrity or functioning of machinery or structures, either continually or periodically, but without any reactive elements. [See also: CONDITION MONITORING, HEALTH MONITORING, STRUCTURAL HEALTH MONITORING] MONEL A nickel-based alloy MONOFILAMENT REINFORCEMENT A reinforcement material used in composites which consists of a single 'wire', unlike the filamentary construction of fibres, e.g. boron filaments, tungsten filaments and some SiC reinforcements. Filaments often consist of layers of various materials deposited onto a carrier fibre core, the external layer being often designed to act as a diffusion coating or barrier. Normally for metal or ceramic matrix materials MONOFILAMENT YARN For technical textiles: a single filament MONOLITHIC CERAMIC A ceramic material which does not contain any deliberately introduced reinforcing phase, e.g. whiskers or fibres. Normally brittle, they are prone to catastrophic failure if over stressed, especially in tension. Common engineering uses include coatings, insulators, electronic substrates, refractory linings etc. [See also: CERAMIC] MONOPROPELLANT Single chemical component rocket fuel which spontaneously decomposes in the presence a catalyst material [See also: BIPROPELLANT] MOS Metal-oxide Semiconductor MoS2 Molybdenum disulphide MOULD 1 The cavity or matrix in or on which the plastic composition is placed and from which it takes its form. 2 To shape plastic parts or finished articles by heat and pressure. 3 The assembly of all the parts that function collectively in the moulding process MOULD RELEASE AGENT Lubricant applied to mould surfaces to facilitate release of the moulded part MOULDING The shaping of a plastic composition in or on a mould, normally accomplished under heat and pressure, sometimes used to denote the finished part MOULDING, PRESSURE-BAG [See: PRESSURE-BAG MOULDING] MPCS Mobile part carrier structure; part of SILEX MRB Material Review Board M.S Margin of safety Ms Martensite start temperature MS Mass-spectrometer MSG Meteosat second-generation MSTP Manned Space Transportation Programme MU Mock-Up MULTIDIRECTIONAL 1 Having multiple ply orientations in a laminate 2 Composite laminates in which the properties are controlled by the orientation of the reinforcement fibres, i.e. fibre-controlled MULTIFILAMENT YARN Multiple fine, continuous filaments (often 5 to 100), usually with some twist in the yarn to facilitate handling. Sizes range from 5 to 10 denier up to a few hundred denier. Individual filaments in a multifilament yarn are usually about 1 to 5 denier. [See also: DENIER] MULTIPLE-WOUND YARN For technical textiles: two or more yarns wound, but not twisted, together MW Multiwall, e.g. titanium multiwall construction; a type of thermal protection system MWt Molecular weight MZ Mach-Zehnder. A type of interferometer for high-resolution phase analysis used in structural health monitoring systems N N2O4 Nitrogen tetroxide; also known as NTO NaCl Sodium chloride; salt NANOTECHNOLOGY The ability to manufacture and control devices (sensory, reactive or combined) in the nanometre range, i.e. smaller than current micrometer size devices NASA National Aeronautics and Space Administration NASA FLAGRO Fracture mechanics analysis software developed by NASA NASA MESUR Network Mars lander NASP National aerospace plane; designated X-30 under the USA X-programme vehicles NBR Nitrile butyl rubber; a material used for seals NBS United States National Bureau of Standards, USA NCR Non-conformance report NDC Nondestructive characterisation, [See: NONDESTRUCTIVE] NDE Nondestructive evaluation, [See: NONDESTRUCTIVE] NDI Nondestructive inspection, [See: NONDESTRUCTIVE] NDT Nondestructive testing, [See: NONDESTRUCTIVE] NEAR-NET SHAPE Component produced with very little finishing required after the major manufacturing operation; also described as net-shape NETTING ANALYSIS The analysis of filament-wound structures which assumes that the stresses induced in the structure are carried entirely by the filaments, the strength of the resin being neglected, and that the filaments possess no bending or shearing stiffness, carrying only the axial tensile loads NEURAL NETWORK Computer science terminology. Objective to build computer systems which function in a similar manner to biological nervous systems. Able to be trained and operate at high speeds NF Norme Franaise; French national standard NICALON( A family of continuous multi-filament silicon carbide fibres derived from the conversion of an organic silicone polymer, polycarbosilane (PCS). Produced by Nippon Carbon Co. NICKEL (Ni) Metallic element, melting point 1455C, density 8900 kg.m-3. Uses: most common superalloy base element; high temperature engine components; alloying addition to many other systems NICKEL ALUMINIDE (Ni3Al) High-strength, brittle intermetallic material, used as coatings or as the matrix in intermetallic matrix composites NIST National Institute of Standards and Technology, USA; standards NiTi A family of shape memory alloys based on nickel and titanium, [See also: SHAPE MEMORY] NITINOL( A proprietary shape memory alloy with a NiTi chemical composition NITRIDE Compound of nitrogen and a metal, often very hard and brittle. Often used as an external hardening treatment for steels, as hardening agents within alloys, e.g. silicon nitride is a widely used ceramic, with or without reinforcement NLR Nationaal Lucht-en Ruimtevaartlaboratorium; Dutch national aerospace laboratory NMR Nuclear magnetic resonance NO GROWTH CRITERION Comprehensively demonstrated condition under which an anomaly or damage does not grow to an extent where the mechanical properties are down-graded so as to impair the residual strength or stiffness of the structure. (The residual strength of the structure is equal to or greater than the strength required for the specified design loads and the stiffness is maintained at the level required for all operating conditions) NOL Naval Ordnance Laboratory NOMEX( An aramid fibre blend from Dupont NON-ASSESSED PROCESS A process that has no history of previous use in the space environment, and for which no or insufficient data are available relevant to the required project application NON CONFORMANCE An apparent or proven condition of any item or documentation that does not conform to specified requirements or which could lead to incorrect operation or performance of the item or mission. The term nonconformance is also used for, e.g. failure, discrepancy, defect, anomaly, malfunction, deficiency NON-CRITICAL MECHANICAL PART Any mechanical part that does not fall under the critical mechanical part definition [See: CRITICAL MECHANICAL PART] NON-CRITICAL PROCESS Any process part that does not fall under the critical process part definition [See: CRITICAL PROCESS] NON DESTRUCTIVE Techniques used to qualitatively evaluate or quantitatively measure properties or detect defects in materials, structural components or whole structures which do not cause a permanent change to the item under test, e.g. ultrasound, holography, eddy current. The terms NDI (inspection), NDT (testing), NDC (characterisation) and NDE (evaluation) tend to be interchangeable. Nondestructive inspection systems can be manually interpreted or automated to some extent. All require calibration, and the detection limit for each technique varies. Note: No one technique is capable of detecting all types of defects NON-DESTRUCTIVE INSPECTION (NDI) 1 General: [See: NONDESTRUCTIVE] 2 Inspection techniques that do not cause physical or chemical changes to the item being inspected or otherwise impair its adequacy for operational service, and that are applied to materials and structures to verify required integrity and detect and characterise cracks. NDI method refers to the specific technique used, such as dye penetrant, X-ray. NDI level refers to the degree of resolution of the technique 3 Special Nondestructive Inspection: The formal inspection of items using non-destructive procedures involving the use of techniques or equipment that exceed common industrial standards 4 Standard Nondestructive Inspection: The formal inspection of items using non- destructive procedures consistent with common industrial standards. These include standard dye-penetrant, eddy-current, ultrasonic and X-ray procedures NON-HOOKEAN A material that does not behave according to Hookes Law, i.e. non-elastically, [See: GENERALISED HOOKES LAW] NON-MECHANICAL STRESS Originated from curing and hygrothermal stress NON-WOVEN TEXTILE 1 For technical textiles: fibrous sheet-materials, [See also: FLEECE] 2 Space applications: it can be used in the core of a flexible external insulation system. [See also: FEI] NOTCH Testing: a specimen that contains a feature to simulate a stress raiser, e.g. a hole or slit NOTCH FACTOR Ratio of the resilience determined on a plain specimen, to the resilience determined on a notched specimen NOTCH SENSITIVITY The extent to which the sensitivity of a material to fracture is increased by the presence of a surface inhomogeneity such as a notch, a sudden change in section, a crack, or a scratch. Low notch sensitivity is usually associated with ductile materials and high notch sensitivity with brittle materials NOTCHED STRENGTH The effective strength of a plate with such stress-raisers as holes, notches and cracks NOTCHED TENSILE Tensile stress test of a specimen containing a deliberately introduced flaw. Many standard test specimens with a variety of machined 'defects' exist in an attempt to model 'real' defects NRB Non conformance review board NTO Nitrogen tetroxide. A constituent of some bipropellant rocket fuels, [See also: MMH] NSTS The National Space Transportation System (US Space Shuttle) O OA Optical assembly; part of SILEX OASIS On-line alerting of structural integrity and safety OASPL Overall acoustic sound pressure level OBDH On Board data handling OCDP Optical coherence domain polarimetry. A fibre optic-based temperature measurement system ODS Oxide dispersion strengthened (metal alloys) OFBG Optical fibre Bragg grating, [See also: BRAGG GRATING] OFF-AXIS Not coincident with the axis of symmetry. Note: Also called off-angle OFFES Outer fabric for European space suit OFFGASSED PRODUCT An organic or inorganic compound evolved from a material or assembled article or experiment or rack, Ref. [7] OFFGASSING 1 General: Depending on the application, there are restrictions on the gaseous products released from materials or finished articles in operational vacuum conditions that can: - contaminate other equipment, [See also: OUTGASSING] - contaminate the air during preparatory or operational conditions for manned spacecraft. 2 The evolution of gaseous products for an assembled article subjected to slight radiant heat in the specified test atmosphere, Ref. [7]. Note: It applies to materials and assembled articles to be used in a manned space vehicle crew compartment OFT Orbital flight test OGSE Optical ground support equipment OHB Optical head bench; part of SILEX OHTH Optical head thermal hood; part of SILEX OMS Orbital manoeuvring system or subsystem OREX Orbital re-entry experiment ON-AXIS Coincident with the axis of symmetry; also known as on-angle, [See: ORTHOTROPIC] ONERA  HYPERLINK "http://www.onera.fr/" Office National d'Etudes et de Recherches Aerospatiales. French national aerospace research organisation ON-ORBIT Verification phase valid for projects whose characteristics, e.g. mission, on-orbit operations, etc. require on-orbit verification. The on-orbit phase has the objective to supplement ground testing by providing operating conditions which cannot be fully or cost effectively duplicated or simulated on the ground, Ref.[1] OPS Oxidation-protection system; a coating system for carbon-carbon composites OPTICAL FIBRE 1 General: A single discrete filament-shaped transparent dielectric material, usually made of glass or plastic, which guides light. It normally has a cylindrical core with one or more external cladding materials applied. The cladding materials have a refractive index higher than that of the core in order to ensure that light propagates within the core, Ref.[4] 2 Smart technologies: A specially manufactured glass optical fibre device usually with some sensory function that can relay light signals usually over long distances. Depending on the precise structure, many signals can be sent and received at the same time, [See also: FIBRE OPTIC] OPTIMUM LAMINATE Having the highest stiffness or strength per unit mass or cost OP TML Out-of-phase thermo-mechanical fatigue ORFEUS Orbiting and retrievable far and extreme ultraviolet spectrometer ORTHOTROPIC A description of material symmetry where the x-axis and y-axis of a laminate coincide with the longitudinal and transverse directions of the material; also know as on axis ORTHOTROPY Having three mutually perpendicular planes of symmetry. Unidirectional plies, fabric, cross-ply and angle-ply laminates are all orthotropic ORS Part of Austrian Aerospace GmbH, since 1997 ORTHOGONAL WEAVE A fabric in which the warp and weft directions are 90 to each other ORU Orbital Replaceable Unit OSR Optical Solar Reflector OTA Optical Telescope Assembly OTDR Optical Time Domain Reflectometry OTV Orbital Transfer Vehicle OUTGASSING 1 General: Depending on the application, there are restrictions on the gaseous products released from materials or finished articles in operational vacuum conditions that can: - contaminate other equipment (outgassing) - contaminate the air during preparatory or operational conditions for manned spacecraft, [See: OFFGASSING] 2 Release of gaseous species from a specimen under high vacuum conditions, Ref. [8] OVERLAP A simple adhesive joint, in which the surface of one adherend extends past the leading edge of another OVERLAY COATING Coating applied to the surface of a component. Often containing inert, oxide materials, acting as a physical barrier to corrosion, temperature or erosion. Common formulae are based on MCrAlY, where M=Ni, Co or Fe. Silicon Carbide coatings are also used OXIDATION 1 Process of attack by oxygen, usually at elevated temperature. 2 Oxide coatings on ceramics, [See: CVD] 3 Oxide coatings on metals, [See: DIFFUSION COATINGS] OXIDATION RESISTANCE A measure of the ability of a material not to degrade or deteriorate under conditions where oxygen is present, usually at elevated temperatures, for a particular time OXIDE DISPERSION STRENGTHENING (ODS) The generation of very fine, sub-micrometre particles of oxides and their addition to a metal with the objective of modifying the base material's deformation properties. Normally achieved by powder attrition techniques, [See also: MECHANICAL ALLOYING] P P/L Payload PA Product Assurance PAET Planetary Aerothermal Experiment Test PAI Polyamide-imide; a polymer PALLADIUM Metallic element, melting point 1555C, density 12020 kg m-3. Uses: constituent of high-temperature brazing alloys PAM Payload Assist Module PAN 1 Polyacrylnitrile; a range of carbon fibres 2 Process of producing carbon fibres in which a chain of carbon atoms is separated from polyacrylnitrile through heating and oxidation. The other process for producing carbon fibres uses pitch as the precursor material PAO Anti-oxidation coating system for carbon-carbon composites PAP Propulseurs dappoint poudre PART 1 A component usually manufactured using one or more processes, e.g. a laminated sheet 2 A mechanical part, Ref. [6] PARTICULATE 1 A material in which the aspect ratio is small; a discontinuous reinforcement 2 Powder or fine grit, usually ceramic, used for reinforcement phase in metal alloys, [See also: PARTICULATE REINFORCED METAL (MMCp)] PARTICULATE REINFORCED METAL (MMCp) Metal matrix composite produced by introducing a finely dispersed, hard, brittle powder phase into a metal alloy. These particulate materials are often carbides or oxides. This is usually achieved either with molten metal (casting) or by mixing with powdered metals (powder metallurgy). Particulate sizes are typically between 3m and 20m, i.e. much larger than those for oxide dispersion strengthened (ODS) alloys PASSIVATION The treatment of metal surfaces, often with acid solutions (or pastes), to remove contaminants and promote the formation of a stable oxide film PASTE Adhesive: a single- or two-component adhesive that often includes a thickening agent, such as microballoons, that behaves as a viscous liquid PAYLOAD ASSIST MODULE (PAM) Concept using a large solid-rocket motor as a perigee injection stage incorporated as part of the users payload rather than as part of the launch vehicle system, e.g. PAM-A: Atlas-sized, PAM-D: Delta-sized PAYLOAD Any equipment or material carried by the launcher that is not considered part of the basic launcher itself. It therefore includes items such as free-flying automated spacecraft, individual experiments and instruments, Ref. [5] PBI Polybenzimidazole; a type of fibre from Celanese PC Personal computer PCB Printed circuit board PDR Preliminary Design Review P-E Pulse-echo; an ultrasonic testing process using one transducer placed on one side of the material under test; also known as pitch-catch PECVD Plasma Enhanced Chemical Vapour Deposition PEEK Poly-ether-ether-ketone: a linear aromatic crystalline thermoplastic. [See also: THERMOPLASTIC] PEEL PLY Sacreficial sheets of material, usually a fabric, applied to the external surfaces of composites; after processing peel plies are removed to provide a clean, contaminant-free surface PEEL STRENGTH Bond strength, obtained by peeling the layer PEI Polyetherimide PERFLUORONATED Containing fluorine; usually applied to polymers, e.g. Teflon"! PERFORMANCE FACTOR The efficiency of a pressure case is given by the performance factor: EMBED Equation  where: v : volume of the vessel, p : burst pressure, m : weight of the structure. Note: Dimension of k is km PES Polyethersulfone thermoplastic. [See also: THERMOPLASTIC] PFCI Potential Fracture-critical Item PFCIL Potential Fracture-critical Item List PFM Protoflight Model PHENOLIC RESIN Thermosetting resin for elevated temperature use produced by the condensation of an aromatic alcohol with an -aldehyde, particularly of phenol with formaldehyde PHENOLIN RESIN [See: PHENOLIC RESIN] PHPV Pneumatic high pressure vessel PHYSICAL VAPOUR DEPOSITION (PVD) Coating manufacturing technique in which metal atoms or ions are transferred from a donor material to a substrate whilst under vacuum. Variants to the basic method are electron beam (EB-PVD), sputtering, ion plating and sputter ion plating (SIP) PI Polyimide; resin for elevated temperature. [See also: POLYIMIDE] PICK Tows in the weft direction of a fabric PID Process Identification Document PIEZOCERAMIC A ceramic-based material which exhibits the piezoelectric effect, such as lithium niobate (LiNbO3), single crystals of quartz (SiO2); ferroelectric ceramics, such as barium titanate (BaTiO3) and lead zirconate titanate (PZT). Applications include sensors for smart technologies and inspection systems, e.g. ultrasonic and acoustic emission, [See also: PIEZOELECTRIC] PIEZOELECTRIC A class of materials which develop voltages across them when loaded or a mechanical force when a voltage is applied. [See also: PIEZOCERAMIC and PVdF] PILE A discontinous fibre in the through-thickness direction of a fabric; a type of triaxial fabric; also known as quasi-3-D or 2.5-D fabrics PIN HOLE A small hole PIP A repeated resin infiltration and pyrolysis process, developed by Dornier for manufacturing ceramic matrix composites (CMC) PITCH FIBRE Carbon fibre made from pitch. The other process for producing carbon fibres uses Polyacrylnitrile (PAN) as the precursor material PLAIN A type of weave for a fabric, [See: PLAIN WEAVE] PLAIN WEAVE A fabric in which each warp and weft thread passes over one end (or pick) and under the next; also known as Square weave PLANAR FLOW CASTING A continuous casting process for the production of rapidly solidified amorphous and microcrystalline metal alloy sheets PLANAR HELIX WINDING A winding in which the filament path on each dome lies in a plane which intersects the dome, while a helical path over the cylindrical section is connected to the dome paths PLANAR WINDING A winding in which a filament path lies in a plane intersecting the winding surface PLANE STRAIN FRACTURE TOUGHNESS (KIC) [See: CRITICAL STRESS INTENSITY FACTOR] PLANCK CFRP satellite mirror structure. The ESA Planck Surveyor mission studied the cosmic microwave background radiation (CMBR) PLASMA SPRAYING Processing methods for depositing metal, ceramic or mixtures of the two onto a substrate from powder or wire feed-stock. Variants to basic method are vacuum, low-pressure (LPPS) and RF. Uses: coatings, matrix deposition onto fibre-reinforcement (MMC ply manufacture), matrix foils and particulate reinforced MMC PLASTIC A material that contains as an essential ingredient an organic substance of high molecular weight, is solid in its finished state, and at some stage in its manufacture or processing into finished articles can be shaped by flow; made of plastic PLATINUM (Pt) Metallic element, melting point 1769C, density 21450 kg.m-3. Uses: alloying additions, coatings PLM Payload Module PLY A single layer of a laminated stack of composite material (or a single pass for a filament-wound configuration) PLY DROP The position inside a laminate where a ply is terminated, e.g. to create a tapered thickness PLY GROUP Group formed by contiguous plies with the same angle PLYING For technical textiles: [See: FOLDED YARN] PLY STRAIN Those components in a ply which, according to the laminated plate theory, are the same as those of the laminate PLY STRESS Those components in a ply that vary from ply to ply, depending on the materials and angles in the laminate PMN Lead-magnesium-niobate. A piezoceramic and thermo-electrostrictive material PMP Parts, Materials and Processes POD Probability of detection POINT STRESS CRITERION A failure criterion where it is assumed that failure occurs when the stress over some distance away from the discontinuity is equal to or greater than the strength of the unnotched laminate POISSONS RATIO (1) Ratio of lateral strain to axial strain in an axial loaded specimen:  EMBED Equation.3  where: ( is Poisson's ratio; (y is strain normal to direction of loading (lateral strain); (y is strain in the direction of loading (axial strain) (2) Poissons ratio is the constant that relates modulus of rigidity to Young's modulus in the equation:  EMBED Equation.3  where: E is Young's modulus; G, modulus of rigidity; and (, Poisson's ratio. The formula is valid only within the elastic limit of a material. A method for determining Poisson's ratio is given in ASTM E-132 POLAR WINDING A winding in which the filament path passes tangent to the polar opening at one end of the chamber and tangent to the opposite side of the polar opening at the other end. A one-circuit pattern is inherent in the system POLYAMIDE A polymer in which the structural units are linked by amide or thio-amide grouping; many polyamides are fibre-forming POLYESTERS Thermosetting resins produced by dissolving unsaturated, generally linear alkyd resins in a vinyl active monomer, e.g. styrene, methyl styrene, or diallyl phthalate POLYIMIDE A polymer produced by reacting an aromatic dianhydride with an aromatic diamine; used for the matrix phase of composites; highly heat-resistant resin above 315*C typically POLYMER A high molecular weight organic compound, natural or synthetic, with a structure that can be represented by a repeated small unit, the mer, e.g. polyethylene, rubber and cellulose, Ref. [9]. Note: Synthetic polymers are formed by addition or condensation polymerisation of monomers. Some polymers are elastomers, some plastics POLYMERISATION A chemical reaction in which the molecules of a monomer are linked together to form large molecules whose molecular weight is a multiple of that of the original substance POLYVINYLIDENE DIFLUORIDE (PVdF) A polymer material which exhibits piezoelectric characteristics, [See: PIEZOELECTRIC] POROSITY Voids remaining in a material or component after manufacture, e.g. gas bubbles in fibre-reinforced resin products, gas or vacuum voids in metal castings. The porosity of a material is normally expressed as the ratio of the volume of air or void contained within the boundaries of a material to the total volume (solid material plus air or void), expressed as a percentage; also known as voidage and void content POST TEST REVIEW The objective is to review the preliminary results declaring the test completion, Ref.[1] POSTCURE An additional elevated-temperature cure, usually without pressure, to improve final properties or complete the cure. Complete cure and ultimate mechanical properties of certain resins are attained only by exposure of the cured resin to higher temperatures than those of curing POST-LANDING Verification phase valid for multi-mission projects. The post-landing phase has the objective to verify recycled hardware and software between missions, hardware and software needed for next flight and not previously verified, an article which has been modified since last usage and functional paths (at periodical intervals) during storage periods, Ref.[1] POT LIFE The length of time a catalysed resin system retains a viscosity low enough to be used in processing; also called 'Working Life', Ref. [10] POTENTIALLY FRACTURE CRITICAL ITEM (PFCI) A structural detail, structural element or structural assembly that is judged to be potentially fracture critical because of the potential critical reduction in flight residual strength or critical loss of structural function that is a consequence of its failure POTTING COMPOUND A polymer resin that usually contains a thickening agent to modify the viscosity and flow characteristics; used for retaining inserts in sandwich panels POWDER METALLURGY (PM) The forming of components from elemental, alloy or compound precursor materials in powder form. There are many process variants but the basic method consists of: blending of powders, shaping and pressing, heat treatment to consolidate component and remove porosity. In some variants these can be carried out simultaneously. PM allows good control of microstructure and can produce components to very high dimensional tolerance POWDER PROCESSING Techniques applicable to materials in a powder form. [See also: POWDER METALLURGY (PM)] PPL Preferred Parts List ppm Parts per million PPS Polyphenylenesulphide PRECIOUS METAL Metallic elements which are relatively scarce, often difficult to extract and hence have a high market price, e.g. gold, platinum PRECIPITATION HARDENING Strengthening mechanism for some metal alloys. Alloy is solution heat-treated to retain alloying elements in a solid solution. Subsequent, lower temperature heat treatment enables controlled growth of finely dispersed second phase precipitates. Greatest strength is usually achieved by stopping short of true precipitates, retaining a continuous, but strained, crystal lattice through the 'enrichment zones' PREFORM Fibres arranged, often woven, into a shape prior to manufacture of a composite, e.g. by matrix infiltration. 1 A pre-shaped fibrous reinforcement formed by distribution of chopped fibres by air, water flotation, or vacuum over the surface of a perforated screen to the approximate contour and thickness desired in the finished part 2 A pre-shaped fibrous reinforcement of mat or cloth formed to the desired shape on a mandrel or mock-up before being placed in a mould press PRE-LAUNCH Verification phase with the objective to verify that the flight article is properly configured for launch and, to the extent practical, it is capable to function as planned for launch. In the mean time, the Ground Support Equipment readiness to support launch is verified, Ref.[1] PREPREG Abbreviation of pre-impregnated; a woven or unidirectional ply or roving impregnated with a resin, usually advanced to B-stage, ready for lay-up or winding, Ref. [10]. [See also: B-STAGE, TAPE] prEN Provisional or draft EN standard PRESS CLAVING A process method for thermoplastic-based composites; a thermoforming technique PRESS MOULDING A process for manufacturing composite materials PRESSURE INFILTRATION CASTING Types of melt infiltration techniques for MMC production conducted in a pressure vessel PRESSURE LEVELS Three pressure levels determine the design of a pressure vessel: 1 MEOP: The maximum expected operational pressure level during the lifetime of the vessel 2 Proof Level: The pressure level which has to be proven for acceptance of a case. This level is normally higher than the MEOP level. The distance between these two levels is dependent on the application. For low- or medium-pressure application the difference is about 5%; for high-pressure application, a difference of 50% is normally requested. At proof level, no failures that influence the behaviour of the case during its lifetime are allowed 3 Burst Level: Requested minimum value before failure of the structure, with requested reliability. The difference between this and MEOP is about 25% for low- or medium- pressure application and about 100% for high-pressure application Note: For vessels with a load-carrying metallic liner, a fourth pressure level has to be taken into account. It is then required that the yield strength of the liner be reached at a pressure level significantly higher than the proof level (about 75% higher than the MEOP) for higher-pressure application PRESSURE VESSEL A pressurised container which: 1 contains stored energy of 19310 joules (14240 foot-pounds) or more, the amount being based on the adiabatic expansion of a perfect gas, or 2 contains a gas or liquid which will create a hazard if released, or 3 experiences a design limit pressure greater than 0.69 MPa (100 psi) PRESSURE-BAG MOULDING A process for moulding reinforced plastics, in which a tailored flexible bag is placed over the contact lay-up on the mould, sealed, and clamped in place. Fluid pressure, usually compressed air, is exerted on the bag, and the part is cured PRIMER A coating applied to a surface before the application of an adhesive, lacquer, paint, enamel or the like to improve the performance of the bond PRINCIPAL DIRECTION Orientation of the specific co-ordinate axes when stress and strain components reach maximum and minimum for the normal components, and zero for the shear PROCESS Set of inter-related resources and activities which transforms a material or semi-finished product into a semi-finished product or final product, Ref. [6] PROCESS VALIDATION [See: VALIDATION OF PROCESSES] PROOF STRESS (PS) Stress at which permanent (non-elastic) deformation occurs in a material. Normally expressed as the stress required to produce a certain amount of permanent deformation, e.g. 0.2% proof stress, the stress to produce 0.2% permanent deformation PROOF TEST The test of a flight structure at a proof load or pressure that gives evidence of satisfactory workmanship and material quality or establishes the initial crack sizes in the structure, Ref. [5] PROTECTION SYSTEM A number of materials applied, often to components, designed to resist the operational environment, e.g. aluminising of superalloys or glassy layers on carbon-carbon composites PROTOFLIGHT MODEL The flight end item on which a partial or complete protoflight qualification test campaign is performed before flight, Ref.[1] PROTOFLIGHT PHILOSOPHY Model philosophy based on a single model (Protoflight Model) to be flown after it has been subjected to a protoflight qualification and acceptance test campaign. Typical philosophy for projects with no technology-critical design and compromise permitted to reduce cost, accepting a medium risk, Ref.[1]. [See also: PROTOFLIGHT MODEL] PROTOTYPE PHILOSOPHY Model philosophy making an extensive use of physical models to cover verification necessities. Typical for projects for which all affordable measures are taken to achieve minimum risk, Ref.[1] PRR Preliminary Requirement Review PRT Placement of Relaxed Fibre Technique PS 1 Polysulfone; a high-temperature-resistant thermoplastic polymer. [See also: THERMOPLASTIC] 2 Poe and Sova; a fracture model psi Pounds per sqaure inch PSI Polysiloxane-etherimide; a polymer PSI/PAI A molecular composite comprising of both polysiloxane-etherimide and polyamide-imide polymers, [See: MOLECULAR COMPOSITE] PSS Procedures, specifications and standards; previous ESA documentation classification system under going transfer to ECSS PTC Passive Thermal Control PTFE Polytetrafluoroethylene PTR Post Test Review PULTRUSION Reversed extrusion of resin-impregnated roving in the manufacture of rods, tubes and structural shapes of a permanent cross section. After passing through the resin dip-tank, the roving is drawn through a die to form the desired cross section PVA Polyvinyl acetate PVC Polyvinylchloride PVD Physical vapour deposition PVDF or PVdF Polyvinylidene fluoride. A piezoelectric polymer material used in smart technologies and sensors PVS Procedure Variation Sheet PWG Pipes, Wetherhold and Gillespie; a fracture model PYROELECTRICITY Development of electrical polarisation in special classes of crystals that are subjected to a temperature change PYROLYSED, PYROLYSATION [See: PYROLYSIS] PYROLYSIS A high-temperature processing method often used to convert a precursor infiltrated liquid (carbon-rich) to a composite matrix phase, e.g. carbon. Note: The process is often repeated after subsequent infiltrations, [See also: IN-SITU SILICONISING] PZT Lead-zirconate-titanate. A piezoceramic material Q QA Quality assurance QCM Quartz crystal microbalance QM Qualification model QNDE Quantitative non-destructive evaluation QPL Qualified parts list QR Qualification review QRR Qualification review report QUALIFICATION Verification phase with the objective to demonstrate that the design meets the applicable requirements including proper margins, Ref.[1] QUALIFICATION ANALYSIS This is performed where it is required to demonstrate that, Ref.[1]: - the as-designed system implements features that are additional to the system functions, performances and interfaces, and - system architectural features and operational interactions on ground and in-orbit are to be implemented QUALIFICATION MARGIN An increase in the environmental range used for qualification testing in order to, Ref.[1]: - avoid qualification test levels that are less severe than the flight ones, - accommodate differences among qualification and flight units due to variations in parts, materials, processes, manufacturing and degradation during usage, and - assure against fatigue failures due to repeated testing and operational use, e.g. acceptance and flight QUALIFICATION MODEL Physical model fully reflecting the flight end item design in all aspects, used for full level functional and environmental qualification tests, Ref.[1] QUARTZ Silica; silicon dioxide QUARTZ CRYSTAL MICROBALANCE (QCM) A device for measuring small quantities of mass deposited on a quartz crystal using the properties of a crystal oscillator, Ref. [8] QUASI-ISOTROPIC LAMINATE A laminate approximating isotropy by orientation of plies in several or more directions R R The ratio of the minimum stress to maximum stress, Ref. [5] R - CURVE Graphical representation of fracture energy against crack length RACK Structure where different experiments will take place during a manned mission, Ref. [7] RAM The direction of spacecraft motion RAMJET A type of combustion engine requiring no turbine parts. High velocity air entering the engine is used to pressurise the fuel and air combustion mixture, [See also: SCRAMJET] RAMP-UP Cure cycle: the increase of temperature to the process temperature RANKING Ordering of laminates by strength, stiffness or other properties RAPIDLY SOLIDIFIED POWDER (RSP) Powder metallurgy technique involving very fast cooling for producing highly alloyed (supersaturated) powder or very fine grain structures RARE EARTH METAL Group of chemical elements with atomic numbers 58 to 71, e.g. cerium, erbium. Used in alloying, or as thin films RCC Reinforced Carbon-Carbon (NASA) replaced by ACC RCG Reaction Cured Glass RCS Reaction Control System REACTION BONDING A manufacturing process similar in principle to sintering for ceramic or MMC production, where a gas or reactive elemental powder is used to chemically bond the constituents, e.g. nitrogen gas for silicon nitride production RECOVERED MASS LOSS (RML) The total mass loss of the specimen itself without the absorbed water (RML = TML - WVR).Note: The RML is introduced because water is not always seen as a critical contaminant in spacecraft materials, Ref. [8] RECRYSTALLISATION Heat treatment of metal alloys; heating to a temperature where a new, strain free, crystal structure develops, removing any previous strain-hardening of the material. Strength decreases and ductility increases. Heating above the recrystallisation temperature leads to a progressive increase in grain size REFRACTORY FIBRES Reinforcement fibres made of boron, silicon carbide and alumina; used for metal and ceramic matrix composites REFRACTORY METAL Group of metal or alloys, including W, Re, Ta and Mo, which possess high-temperature stability, e.g. high melting point although some have poor oxidation resistance at high temperatures REI Rigid External Insulation REINFORCED PLASTIC A plastic with strength properties greatly superior to those of the base resin, resulting from the presence of reinforcements embedded in the composition REINFORCEMENT A strong inert material bonded into a plastic, metal or ceramic to improve its strength, stiffness and impact resistance. Reinforcements are usually long fibres of glass, boron, graphite or aramid, in woven or non woven form. To be effective, the reinforcing material must form a strong adhesive bond with the matrix Note: 'Reinforcement' is not synonymous with 'filler' RELATIVE DIELECTRIC CONSTANT (SYMBOL 101 \f "Symbol") A measure of the electrical properties of a material; varies for different polymer resins, [See also: DIELECTRIC] RELATIVE HUMIDITY (RH) A measure of the moisture content of an atmosphere with respect to the fully saturated atmosphere at the same temperature and pressure; expressed as a percentage RELAXATION A change in shape resulting from exposure to continuous loading or temperature RELEASE AGENT A material which is applied in a thin film to the surface of a mould to keep the resin from bonding to it RELEASE FILM A thin sheet of material applied to a composite surface to enable its removal from a mould; used in autoclave processing REPAIR Operations performed on a non-conforming item to place it in usable and acceptable condition according to an authorised repair procedure/standard. Repair is distinguished from rework. Note: Repair can consist of a component change with all its associated connections including the fixing down of a lifted pad or track REQUEST FOR APPROVAL (RFA) Document with which the supplier or user asks the competent body for permission to use a critical material, part or process, Ref. [6] REQUIREMENT Within this handbook: a property of a material or a function of a component or structure that is defined as a result of the application within a particular service environment or mission, e.g. mechanical loads, temperature, dimensional stability, galvanic corrosion REQUIREMENT CATEGORY A requirement category identifies a homogeneous set of requirements for which is possible to define a common verification strategy, Ref.[1] RESIDUAL FATIGUE STRENGTH The retention of static strength by a laminate that has been subjected to a certain fatigue-load history RESIDUAL STRAIN Coatings: a strain which remains locked into a material after processing. Further loading can result in coating fracture RESIDUAL STRENGTH The retention of static strength by a laminate that has been subjected to a load history or environment RESIDUAL STRESS 1 A stress that remains in the material or structure, owing to processing, fabrication or prior loading 2 Composites: Resulting from cool-down after cure and change in moisture content. On the micromechanical level, stress is tensile in the resin and compressive in the fibre. On the macro-mechanical level, it is tensile in the transverse direction to the unidirectional fibres, and compressive in the longitudinal direction, resulting in a lowered first-ply-failure load. Moisture absorption offsets this detrimental thermal effect at both micro and macro levels 3 Metals: Usually arises from heat treatment or mechanical working RESIN A solid, semi-solid, or pseudo-solid organic material which has an indefinite (often high) molecular weight, exhibits a tendency to flow when subjected to stress, usually has a softening or melting range, and usually fractures conchoidally. Most resins are polymers. In reinforced plastics, the material used to bind together the reinforcement material, the matrix. [See also: POLYMER] RESIN CONTENT The amount of resin in a laminate expressed as a percent of total weight or total volume RESIN FLOW A measure of the amount of resin exuded from the prepreg during cure processing. Resin flow is a measure of the transient reduction in viscosity that takes place in thermosetting systems as the temperature is increased, prior to gelling. Resin flow has an important effect on the production process and varies widely from system to system RESIN TRANSFER MOULDING (RTM) A technique for infiltrating a fibre preform, held in a mould, with a range of thermosetting resins. Infiltration can be pressure and/or vacuum assisted. Resin cure can be achieved quickly. Uses: production technique for large batch polymer (thermoset) composites. Preliminary process method usually for thick-section C and SiC matrix composites RESIN-RICH AREA Where local resin content is higher than the average of a laminate owing to improper compaction or curing. It can be detrimental because any resin-rich area can mean a resin-starved area somewhere else RESIN-STARVED AREA Where local resin content is lower than the average. It has a dry appearance where the setting of filaments or fabric is not complete. It is probably more detrimental than the resin-rich area REVERSE HELICAL WINDING In filament winding, as the fibre-delivery arm traverses one circuit, a continuous helix is laid down, reversing direction at the polar ends; contrasted to biaxial, compact, or sequential winding in that the fibres cross each other at definite equators, the number depending on the helix. The minimum cross-over would be three REVIEW OF DESIGN PROCEDURE This document lists all the requirements to be verified by Review of Design, grouping them in categories detailing the Verification Plan activity sheets, with planning of the execution and a definition of the associated procedures, Ref.[1] REVIEW OF DESIGN REPORT This document describes each verification activity performed reviewing documentation during program design reviews and contains proper evidence that the relevant requirements are satisfied, Ref.[1] REVIEW OF DESIGN A verification method using validation of previous records or evidence of validated design documents, when approved design reports, technical descriptions, engineering drawings, etc., unambiguously show that the requirement is met, Ref.[1] Note: In US standard: Review of Design = Validation of Records REWORK Reprocessing of a non-conforming item to make it conform to drawing, specification or contract RF Radio frequency R.F. Reserve factor RFA Request for approval RFCP Reduced Fracture-control Programme RFW Request for waiver R-GLASS A high-strength grade of glass fibre, [See also: GLASS FIBRE] RH Relative humidity RHENIUM (Re) Refractory metallic element, melting point 3186C, density 21020 kg m-3. Uses: alloying additions, coatings RIG A fixture or tool that retains a material, sample or structure, e.g. for testing and processing; also known as jig RIGGING LINE Any cord or tape attached to a parachute canopy that transmits the forces on the canopy to the suspended load via lift webs or strops RIM Resin injection moulding RLV Re-useable launch vehicle RML Recovered mass loss RMS Root mean square ROC Receiver operating characteristic; an ultrasonic testing calibration procedure ROD Review of design ROSETTA ESA comet rendevous mission ROTATING MACHINERY Any rotating mechanical assembly that has a kinetic energy of 19 300 joules or more, the amount being based on 0.5 I(2, where I is the moment of inertia (kg.m2) and ( is the angular velocity (rad/s), Ref. [5] ROVING For technical textiles: a number of yarns, strands, tows collected into a parallel bundle with little or no twist. Roving can be impregnated for use in filament winding, in braiding, and in unidirectional tapes ROUND ROBIN An evaluation process whereby the same subject of interest is assessed using the same principles by several different organisations; often used for material evaluation tests to provide a measure of the variability to be expected within the results RSBN Reaction bonded silicon nitride. [See also: REACTION BONDING] RSI Reusable surface insulation (Shuttle Orbiter) RT Room temperature RTM Resin transfer moulding RTV Room-temperature vulcanising, e.g. silicone adhesives RULE OF MIXTURES Linear volume fraction relation between the composite and the corresponding constituent properties; also known as Law of Mixtures e.g. For modulus of a composite Ec, the rule of mixtures equation is:  EMBED Equation.3  where: Ef = modulus of the fibre; Vf = volume fraction of fibre in the composite; Em = modulus of the matrix; Vm = volume fraction of the matrix RUS Resonant ultrasound spectroscopy S SACMA Suppliers of Advanced Composite Materials Association, USA SADM Solar array drive mechanism SAE Society of Automotive Engineers, USA SAFE LIFE 1 A fracture-control acceptability category which requires that the largest undetected crack that can exist in the part will not grow to failure when subjected to the cyclic and sustained loads and environments encountered in the service life, Ref. [5] 2 A potentially fracture critical item (PFCI) is a safe-life item if it can be shown that the largest defect in the part will not grow to an extent where the minimum specified performance (e.g. limit load capability or no leak) is no longer assured within a safe life interval. [See: PFCI] SAFETY FACTOR [See: FACTOR OF SAFETY, LOADS] SAFFIL LD and HD Proprietary types of alumina fibre; LD: low density, HD: high density SAM Scanning acoustic microscope; an ultrasonic materials evaluation technique SANDWICH 1 Construction: An assembly composed of a lightweight core material, such as honeycomb, foamed plastic, and so forth, to which two relatively thin, dense, high-strength or high- stiffness faces or skins are adhered, Ref.[9], [See also: FACE SHEET] 2 Panel: A sandwich construction of a specified dimensions. Note: The honeycomb and face skins can be made of composite material or metal alloy. SNGER German-designed, two-stage, reusable launch vehicle technology programme SAR Synthetic aperture radar SAS Solar Array System SASW Spectral Analysis of Surface Waves SATELLITE An unmanned spacecraft generally oriented to scientific, telecommunication, earth observation missions, Ref.[1] SATIN A type of weave for a fabric, [See: SATIN WEAVE; SATIN 8 WEAVE] SATIN WEAVE Each warp end and weft pick floats over N and under one crossing thread. The weave is described by (N+1), e.g. an 8 harness (8 shaft) satin SATIN 8 in which the weft pick passes over 7 and under one warp end SATIN 8 WEAVE A type of fabric weave, 8 harness (8 shaft) satin in which the weft pick passes over 7 and under one warp end SAW Surface Acoustic Wave SAXS Small angle X-ray scattering SBSS Short beam shear strength; a test method SCARF JOINT [See: JOINT] SCC Stress Corrosion Cracking SCEF Stress Corrosion Evaluation Form SCISSION The breaking of molecular chains; a degradation effect of polymer resins exposed to penetrating radiation (alpha and beta particles) SCRAMJET Supersonic combustion ramjet. A type of combustion engine requiring no turbine parts. High velocity air entering the engine is used to pressurise the fuel/air combustion mixture. Differs from a RAMJET in that combustion takes place at supersonic air velocities through the engine SDI Strategic defense initiative. American space defence programme SDR System Design Review SEAM For technical textiles: a series of stitches or different stitch types, applied to one or more thicknesses of textile, normally a fabric, in order to join them together SECANT MODULUS Idealised Young's modulus derived from a secant drawn between the origin and any point on a non-linear stress/strain curve. Tangent modulus is the other idealised Young's modulus derived from the tangent to the stress/strain curve SECONDARY BONDING A process whereby manufactured component parts are joined by an adhesive; can be applied to composite parts that have already been cured or metal parts or combinations thereof. Note: This is different from co-curing, [See also: CO-CURING] SELF-DESTRUCT Temperature and moisture level that will cause failure without externally applied stress SELF-SIMILAR DAMAGE GROWTH The propagation of a crack through both reinforcement and matrix within a composite, usually caused by excessive bonding between fibre and matrix, resulting in no crack stopping, or crack deviation at the interface. Also known as single crack failures. Applicable to MMC and CMC materials SEM Scanning electron microscope SENB Single-edged notched beam test specimen, used to generate 'R' curves - fracture energy against crack length SEP French company: Socit Europenne de Propulsion SEPCORE A thermal protection system (TPS) heat shield concept from SEP comprising of an ablative layer on a C-SiC structure which protects fibrous insulation. SERIOUS CONSEQUENCE A potential risk situation that can result in: - temporarily disabling but not life-threatening injury, or temporary occupational illness; - loss of, or major damage to, flight systems, major flight system elements or ground facilities; - loss of, or major damage to, public or private property; or - long-term detrimental environmental effects SERR Strain energy release rate SERVICE CONDITIONS The combination of mechanical loading and environmental effects experienced by a material, component or structure in operation over its intended life SERVICE LIFE The interval beginning with an item's inspection after manufacture and ending with completion of its specified life, Ref. [5] SES Suit enclosure subsystem; part of an extra-vehicular activity space suit SEVIRI Spinning enhanced visible and infra red imager instrument S-GLASS A magnesia-alumina-silicate glass, especially designed to provide filaments with very high tensile strength SHAKEDOWN STRESS Term used in tensile testing of MMC materials where a small irrecoverable deformation occurs at low strains, or during the first few load cycles, at a threshold stress SHAPE MEMORY ALLOY (SMA) A metal alloy which, after mechanical deformation in a particular temperature range, will regain its original shape after heating or cooling through a specific temperature. These alloys are used in actuators and in some latching and joining devices Note: The trigger temperature is alloy dependent SHAPE MEMORY EFFECT (SME) A reversible shape change in certain metal alloys arising from a transformation to and from a martensitic structure. Mechanical deformation in the working temperature range for the alloy gives rise to regions of martensite within the crystal structure which, having a different volume, accommodate the shape change. Subsequent heating reverses this effect and so returns the material to its original shape SHEAR LAG MODEL Mathematical model derived to describe behaviour of anisotropic materials, best suited to aligned, short-fibre composites SHEAR MODULUS RATIO Ratio of the shear modulus of the core material to that of the face material in a sandwich construction SHEET MOULDING COMPOUND (SMC) Manufacturing technique using short fibre-reinforced composites SHEET Prepreg of any width, supplied as flat sheet in the form of cut lengths. (Specific definition for 'composites') SHELF LIFE 1 The stated time period in which the manufacturer guarantees the properties or characteristics of a product for the stated storage conditions, Ref. [10]. 2 Prepreg: The period of time during which a prepreg retains the specified flow, tack and cure characteristics when stored under specified conditions. Most prepregs require refrigerated storage in order to achieve useful shelf lives SHM Structural health monitoring SHMS Structural health monitoring system SHOP LIFE The shop life of a prepreg is that period following removal from the specified storage conditions and attaining shop-floor temperature for which the prepreg remains workable in terms of tack, and flow and cure characteristics SHORT-TRANSVERSE (S-T) DIRECTION Equivalent to the through-the-thickness direction of sheet or plate material. For anisotropic materials the short-transverse direction general shows the poorest mechanical properties SHRINKAGE Contraction of a moulded part during and after cure. Parts can meet dimensional tolerance if the dimensional changes due to temperature of the part and the mould are properly considered SI The international system of units, published by the International Standards Organisation (ISO) SIALON Fine-grained non-porous silicon nitride ceramic with a small amount of added aluminium oxide. Approximate properties: Density 3240 kg m-3, Elastic modulus 288 GPa, Flexural strength 760 MPa, Fracture toughness KIC 6.0 MPa m1/2 to 7.5 MPa m1/2, Thermal conductivity 15 W/m K to 20 W/m K, Maximum use temperature (no load) 1200C SIAT Semi-Integrated Aeroshell TPS - Co-operative programme between Dassault-Aviation and DASA/Dornier, covered the activities from 1994 to 1996 on the design of future Mars landing probe aeroshell and thermal protection concepts SiC Silicon carbide SiCf Silicon carbide fibre reinforcement SiCp Silicon carbide particulate reinforcement SiC-SiC Silicon carbide fibre-reinforced silicon carbide; a ceramic matrix composite SiC/Ti Silicon carbide reinforced titanium SILEX Semiconductor laser inter-satellite link experiment SILICA Silicon dioxide (SiO2) SILICON (Si) Non-metallic element, melting point 1414C, density 2330 kg m-3. Uses: alloying additions. [See also: SILICON CARBIDE (SiC)] SILICON CARBIDE (SiC) High strength ceramic material with a density of approximately 3100 kg m-3. Approximate properties: Elastic modulus 410 GPa, Flexural strength 550 MPa, Compressive strength 3900 MPa, Fracture toughness KIC 4.6 MPa.m1/2, Thermal conductivity 120 W/m K, Maximum use temperature (no load) 1650C SILVER (Ag) Metallic element, melting point 962C, density 10500 kg.m-3. Uses: alloying additions, coatings SIMILARITY A verification method used if it can be shown that the article is similar to another article that has already been qualified to equivalent or more stringent criteria. Note: In the European standard similarity is part of Analysis, Ref.[1] SIMOUN Plasma jet test facility at Aerospatiale (Aquitaine), France SINGLE CRYSTAL (SC) A component formed from a single alloy crystal - hence with no internal grain boundaries where high temperature damage processes such as creep, recrystallisation and precipitation are normally most active, [See also CREEP] SINGLE YARN For technical textiles: a yarn that can be composed of either spun, filament, monofilament or multifilament yarn SINTERING A consolidation technique for metal and ceramic compounds by solid phase diffusion or where a constituent has a lower melting point than the others and is molten during the processing. Note: A variant of this process is REACTION BONDING SiO2 Silicon oxide SIP Strain Isolation Pad SIS Support and interface subsystem; the interface between a space vehicle and an extra-vehicular activity space suit SIZE A material often added to fibre tow (in the case of carbon, after surface treatment). This size improves the handling characteristics of the tow and reduces filament damage during subsequent processing, e.g. weaving or prepreg manufacture. When a prepreg with an epoxy-resin matrix is to be manufactured, an epoxy-resin size containing no curing agents is usually specified. Size content with respect to the tow in frequently in the range 0.5% to 1.0% by weight. (Definition specific to 'composite') SIZING 1 Applying a material on a surface in order to fill pores and thus reduce the absorption of the subsequently applied adhesive or coating. 2 Modifying the surface properties of the substrate to improve adhesion. 3 Selecting by design the ply number and angles of a laminate subjected to one or more sets of applied stresses SLA-561 low density silicone ablator SLAM Scanning laser acoustic microscope; a nondestructive materials evaluation technique SLURRY Powdered materials suspended in a liquid phase SLURRY INFILTRATION Also known as colloidal infiltration or slip casting (un-reinforced ceramics). The slurry consisting of the matrix phase (final form or elemental powders), binders, solvents and wetting agent(s) is infiltrated into the reinforcement, dried and fired. Process can also incorporate REACTION BONDING SM Structural Model SMA [See: SHAPE MEMORY ALLOY] SMAC Spacecraft Maximum Allowable Concentration SMART In the context of this handbook: applications in space programmes where the principal requirements are for smart systems with a self inspection (or sensory) capability, with or without an inherent adaptive response SMART STRUCTURE A structure or mechanism with sensory and reactive elements incorporated which, when activated, will monitor or modify the structure or mechanism characteristics SMART TECHNOLOGIES [See: SMART] SMC [See: SHEET MOULDING COMPOUND] SME [See: SHAPE MEMORY EFFECT] SMH Structural materials handbook; ECSS-E-30-04 SMSA Secondary mirror support assembly; part of the Mars Observer Camera S-N CURVE Stress per number of cycles to failure; a graph used to display fatigue testing results SNELLS LAW When a light ray passes into a higher refractive index medium, its path is deviated toward the normal to the surface at the point of incidence, i.e. the refraction angle is less than the incidence angle. When passing into a lower refractive index medium, the refraction angle is greater than the incidence angle, Ref. [4] SOLAR ABSORPTANCE ((s) The relationship between the absorptance of a test item irradiated with a solar simulator to the absorptance the test item would experience from the sun SOLDERING As for brazing, but where the braze (solder) has a very much lower melting temperature. Common solders are often Sn- or Pb-based alloys used for electrical and electronic connections. Note: Special solders exist for use in space SOLELY REACTIVE SMART SYSTEM A structure or mechanism which contains one or more devices for controlling its condition, e.g. shape, stiffness SOLELY SENSORY SMART SYSTEM A structure or mechanism which contains one or more devices for monitoring its condition, e.g. temperature, strain SOL-GEL (Silica impregnation process) A chemical solution containing the ceramic matrix phase constituents in gel form. In sol-gel processing, the gel is infiltrated into the reinforcement, dried and subsequently fired to produce the composite matrix phase SPA Surface Protected Ablator SPACECRAFT A space system which could be either manned or unmanned and could have any type of mission objectives, i.e. telecommunications, transportation, earth observation, interplanetary exploration, Ref.[1] SPACECRAFT MAXIMUM ALLOWABLE CONCENTRATION (SMAC) The maximum concentration of a volatile offgassed product that is allowed in the spacecraft atmosphere for a specified flight duration, Ref. [7] SPACE-PROVEN MATERIAL OR MECHANICAL PART One whose properties are well understood and that is produced by means of a stable process, usually confirmed by a history of continuous or frequent production runs. It must be compliant with a recognised set of specifications. It will have been used in space applications, or will have successfully completed an appropriate evaluation process SPALL 1 The loss of a material or some part of that material, e.g. as the result of impact 2 The loss of a material or substance from a substrate; often as a result of thermal cycling, e.g. coatings SPAS Shuttle palette satellite SPATE Stress pattern analysis by thermoelastic emission; a nondestructive testing technique SPECIAL NONDESTRUCTIVE INSPECTION [See: NONDESTRUCTIVE] SPECIAL PROCESS A process where quality cannot be completely ensured by inspection of the end article only, Ref. [6] SPECIFIC ENERGY (U Damping: the energy dissipated per unit volume of material during one cycle of vibration at a given stress amplitude; defined in absolute terms SPECIFIC GRAVITY (SG) A dimensionless quantity also known as Relative Density. Ratio between the density of a material and that of water under standard conditions SPECIFIC STIFFNESS The measure of the stiffness of a material with respect to its density SPECIFIC STRENGTH The measure of the strength of a material with respect to its density SPELDA Structure Porteuse pour Lancement Double Ariane SPF Superplastic forming SPF/DB Superplastic forming/Diffusion bonding; the combined metal sheet forming and joining process with particular relevance to titanium alloys SPLAT COOLING Very high cooling rate process for producing metal powders. The alloy is melted and liquid droplets are sprayed or dropped onto a chilled surface with high thermal conductivity, e.g. a internally water-cooled copper wheel. The resultant splat particulate is removed from the rotating wheel to allow subsequent droplets to contact the bare, chilled surface SPLIT MOULD A mould in which the cavity is formed of two or more components known as splits, held together by an outer case SPRAY-UP Techniques with a spray gun as the processing tool. In reinforced plastics, for example, glass fibre and resin can be simultaneously deposited in a mould. In essence, roving is fed through a chopper, ejected into a resin stream, and is directed at the mould by either of two spray systems SPRINGBACK Shape distortion of sheet metal after forming resulting from the recovery and equalisation of elastic deformation strain SPUN YARN For technical textiles: a number of discontinuous fibres held together by twist SQUARE A type of weave for a fabric, [See: SQUARE WEAVE] SQUARE WEAVE A type of fabric in which each warp and weft thread passes over one end (or pick) and under the next; also known as Plain weave SQUEEZE CASTING Melt infiltration technique for MMC production using high pressures. Other variants have been developed to reduce damage to reinforcements during processing SRD System Requirement Document SRM Solid rocket motor SRR System Requirement Review SSM Second surface mirror SSME Space shuttle main engine S/S Subsystem SST Supersonic wind tunnel SSTO Single stage to orbit STACKING ORDER or SEQUENCE Ply ordering in a laminate. Stacking sequence does not affect the in-plane properties of a symmetric laminate. Only the ply number and angles are important. But stacking sequence becomes critical for the flexural properties, and the interlaminar stresses for any laminate, symmetric or not; also known as lay-up STAGNATION POINT The point where an impinging gas flow separates around an object STAINLESS STEEL A range of metal alloys containing at least 11% to 12% of chromium, a low percentage of carbon, and often some other elements, notably nickel and molybdenum STAMP Study on Technology of Aerobraking for Mars Penetrators STANDARD NON DESTRUCTIVE INSPECTION [See: NONDESTRUCTIVE} STANDARD OR ESTABLISHED PROCESS One that is well documented, has a previous history of use, is well understood and for which standard inspection procedures exist. Such a process would generally be covered by ESA specifications or other international or national documents STARVED AREA An area in a plastic part which has an insufficient resin to wet out the reinforcement completely. This condition can be due to improper wetting or impregnation or excessive moulding pressure STARVED JOINT An adhesive joint which has been deprived of the proper film thickness of adhesive, owing to insufficient adhesive spreading or application of excessive pressure during lamination STATIC FATIGUE Failure of a part under continued static load; analogous to creep-rupture failure in metal testing, but often the result of ageing accelerated by stress STATIC LOAD (STRESS) A load (stress) of constant magnitude and direction with respect to the structure, Ref. [5] STE Special Test Equipment STICKING COEFFICIENT The probability that a molecule, colliding with a surface, stays on that surface before thermal re-evaporation of that molecule occurs, Ref. [8] STIFFNESS Ratio between the applied stress and the resulting strain. Young's modulus is the stiffness of a material subjected to uniaxial stress; shear modulus to shear stress. For composite materials, stiffness and other properties are dependent on the orientation of the material. [See: MODULUS] STM Structural Thermal Model STOICHIOMETRIC Chemical composition with fixed atomic ratios of constituent elements STORAGE LIFE The length of time that a material can be kept under predetermined conditions and not degrade, e.g. Prepreg: usually -18C for thermosetting resin systems, with subsequent factory floor operations at room temperature, [See also: SHELF LIFE] STRAIN GAUGE Widely used device for point measurement of strain. Usually thin film metals which, when strained, change in electrical resistance. Note: Require calibration and temperature compensation STRAIN RELAXATION [See: CREEP] STRAIN TO FAILURE Total strain experienced by a material before catastrophic failure STRAND For technical textiles: usually an untwisted bundle of continuous filaments used as a unit. Occasionally a single fibre or filament is referred to as a strand STRENGTH PARAMETER Strength coefficient of a quadratic failure criterion in stress or strain space STRENGTH RATIO or STRENGTH/STRESS RATIO Measure related to MARGIN OF SAFETY. Failure occurs when the ratio is unity; safety is assured for example by a factor of 2 if the ratio is 2. The ratio is particularly easy to obtain if the quadratic failure criterion is used STRENGTH Maximum stress that a material can sustain. Like the stiffness of a composite material, this is highly dependent on the direction as well as the sign of the applied stress; e.g. axial tensile, transverse compressive, and others STRESS AMPLITUDE (R) Fatigue test: the range of stresses induced in a laminate when a cyclic load is applied, [See also: R] STRESS CONCENTRATION A localised increase in the stress within a material, component or structure compared with the average stress. These occur as a result of the presence of a design feature or defect, e.g. hole, cut-out or notch, crack, delamination: 1 Micromechanical level: Concentration occurs at the fibre/matrix interface 2 Macro-mechanical level: Concentration occurs at, e.g. holes, notches; ply termination or drop-off points, joints, defects STRESS CONCENTRATION FACTOR The ratio of the maximum stress in the region of a stress concentrator to the stress in a similar strained area without a stress concentrator STRESS CORROSION the combined action of sustained tensile stress and corrosion that can lead to the premature failure of materials STRESS-CORROSION CRACKING (SCC) The initiation and/or propagation of cracks, owing to the combined action of applied sustained stresses, material properties and aggressive environmental effects, Ref. [5]. Usually experienced by metal alloys as pit formation or intergranular attack in aqueous solutions. Note: Composites and plastics can also suffer from stress corrosion cracking STRESS CRACK External or internal cracks in a plastic caused by tensile stresses less than that of its short-time mechanical strength. The stresses which cause cracking can be present internally or externally or can be combinations of these stresses, [See also: CRAZING] STRESS CRACKING The formation of cracks owing to the combined effects of an aggressive environment and internal or external stresses in a polymer; can result in a rapid failure STRESS INTENSITY FACTOR (K) A calculated quantity that is used in fracture mechanics analyses as a measure of the stress-field intensity near the tip of an idealised crack. Calculated for a specific crack size, applied stress level and part geometry. [See: CRITICAL STRESS-INTENSITY FACTOR; FRACTURE TOUGHNESS], Ref. [5] STRESS RELAXATION The decrease in stress under sustained constant strain, also called stress decay STRESS Intensity of forces within a body. The normal components induce length or volume change; the shear component, shape change. The numerical value of each component changes as the reference co-ordinate system rotates. For every stress state there exists a principal direction, a unique direction when the normal components reach maximum and minimum, and the shear component vanishes STRESS-STRAIN CURVE A graphical representation of a material's response to increasing load. Often used to depict relationships between stress(load) and strain (elongation), e.g. stiffness, strength(s)and strain to failure STRESS-STRAIN RELATION A linear relation is usually assumed for calculating stress from strain, or strain from stress. For multidirectional laminates, it can be generalised to include in-plane stress-strain, and flexural stress-strain relations. All anisotropic relations are simple extensions of the isotropic relation STRUCTURAL COMPONENT A major section of the structure (e.g. wing, body, fin, horizontal stabiliser) that can be tested as a complete unit to qualify the structure STRUCTURAL FAILURE [See: FAILURE (STRUCTURAL)] STRUCTURAL HEALTH MONITORING For smart technologies: a diagnostic system which can provide data on the integrity or functioning of structures or structural components, normally continually STRUCTURAL MODEL Physical model fully representative of the flight end item in all mechanical aspects, used for qualification of the structural design and for mathematical models correlation, Ref.[1] STRUCTURAL SUBCOMPONENT A major three-dimensional structure that can provide complete structural representation of a section of the full structure (e.g. stub-box, section of spar, wing panel, wing rib, body panel or frames) STRUCTURAL-THERMAL MODEL Physical model combining the Structural Model and Thermal Model objectives, Ref.[1]. [See also: STRUCTURAL MODEL and THERMAL MODEL] STRUCTURE All items and assemblies designed to sustain loads or pressures, provide stiffness and stability, or provide support or containment STS Space Transportation System (US Space Shuttle) SUBASSEMBLY A subdivision of an assembly consisting of two or more items Note: Verification level typical of US standard, Ref.[1] SUBGRAIN A term used to describe phases within a microstructural grain of a material, usually metal or ceramic, often caused by dislocations or the presence of reinforcement SUBSYSTEM 1 A functional subdivision of a payload consisting of two or more items 2 A set of functionally related equipment, connected to each other, that performs a single category of functions, e.g. structure, power, attitude control, thermal control, Ref.[1] SUITCASE Physical model designed to simulate functional performance both in terms of data handling (telecommand and telemetry as formats, bit rates, packet type, etc.) and radio frequency, Ref.[1] SUPERALLOY A series of alloys with very high operational temperatures with respect to their melting point, e.g. 0.9 Tm. The three groups are Nickel-based, Cobalt-based and Iron-based. SUPERPLASTIC FORMING (SPF) Manufacturing method using materials with superplastic characteristics. Normally a slow process owing to the low strain rates used. Applied to aluminium and titanium alloys and often combined with diffusion bonding to produce 'finished' components SUPERPLASTICITY The ability of heat softened material to undergo very large plastic deformation, e.g. in excess of several 100%, without fracture SURFACE TREATMENT A material applied to fibres during the forming operation or in subsequent processes. [See: SIZE, FINISH or FIBRE SURFACE TREATMENT] SVF Software Validation Facility SVM Service Module S/W Software SWARF Waste material, usually metallic, produced during machining processes SWELLING Increase in volume due to rise in temperature or absorption of moisture 1 Laminates: a change of dimension owing to the absorption of moisture, usually by the matrix SWF Stress wave factor SWRI South West Research Institute, USA; standards SXT Soft X-ray telescope SYLDA Systme de Lanceur Double Ariane 5 (Ariane 5 double launch system) SYMMETRIC LAMINATE Possessing mid-plane symmetry. This is the most common construction, because the curing stresses are also symmetric. The laminate does not twist when the temperature and moisture content change. An unsymmetrical laminate on the other hand twists on cooling down and untwists after absorbing moisture SYSTEM The composite of elements, skills and techniques capable of performing the operational roles. A system includes all operational equipment, related facilities, materials, software, services and personnel required for its operation, e.g. launch system, on-orbit system, Ref.[1] T T Toxic hazard index TAB A material, usually fixed to each end of a test specimen, which enables load to be transferred to the test specimen without causing damage to the test specimen; composite test specimens often have light-alloy or glass-fibre based composite tabs adhesively bonded to the test specimen TACK Stickiness of a prepreg or film adhesive; an important handling characteristic TAFA Thermal acoustic fatigue apparatus. A test facility at NASA Langley, USA TANGENT MODULUS Idealised Youngs modulus derived from the tangent drawn at the origin or any point on a non linear stress-strain curve. Secant modulus is the other idealised Youngs modulus between the origin and same point on the stress-strain curve TANGENTIAL STRESS The normal stress along the tangent of the opening TANTALUM (Ta) Refractory metallic element, melting point 3020C, density 16650 kg m-3. Uses: alloying additions TAPE 1 Unidirectional prepreg of a continuous length including tape splices in the fibre direction (whose position must be indicated by the tape supplier) and of any width, supplied on a reel, [See also: PREPREG] 2 Fabric: widths less than 150 mm TAPE-LAYING A process whereby a tape of material is layed-up to form a composite; often using a computer-controlled machine TBC Thermal barrier coating TBE Tetrabromoethane TC Thermal Control TCL Test Configuration List TEAR RESISTANCE For textiles: the ability of the fabric to resist the propagation of a cut under nominal lo-ads TECHNOLOGY ANALYSIS Related to the assessment of the adequacy of the selected materials, with respect to the required properties, Ref.[1] TEM Transmission electron microscope TEMPER Normally a heat-treatment or prescribed sequence of treatments used on metal alloys which determines their microstructure and properties. [See also: CONDITION] TEMPLATE Pattern used as a guide for cutting and laying plies TERBIUM Metallic element, melting point 1356C, density 8229 kg.m-3, atomic number 65. Terbium-Iron alloy is a magnetostrictive material with potential for smart technologies TEOS Tetra-ortho-ethyl-silicate TEST A verification method wherein requirements are verified by measurement of performance relative to functional, electrical, mechanical and thermal parameters. These measurement can require the use of special equipment, instrumentation and simulation techniques, Ref.[1] TEST ACCURACY Measurement precision based on instrument characteristics. Note: Test accuracy shall be better than related test tolerance: at least one third, Ref.[1] TEST EFFECTIVENESS The number of failures per spacecraft found in the test of interest divided by the total number of failures which are possible to be found in all the acceptance test campaign and during the first 45 days of flight, Ref.[1] TEST FAILURE QUESTIONNAIRE Form dedicated to the collection of project statistical verification information about occurred failures and to eventually feed a dedicated verification historical data base, Ref.[1] TEST LEVEL The environmental level utilised for testing an item. It could be qualification or acceptance test level, Ref.[1] TEST PROCEDURE A document which provides detailed step-by-step instructions to the Test teams for conducting the test activities in agreement with the Test Specification requirements, Ref.[1] TEST READINESS REVIEW The objective of this review is to declare the readiness for the test authorising the start of the test, Ref.[1] TEST REPORT A document which describes Test performance, results and conclusions in the light of the test requirements, Ref.[1] TEST REQUIREMENT SPECIFICATION This document is a system support specification applicable to all verification levels containing the general test requirements in terms of type of tests, sequences, margins, durations, tolerances, screening policy and methodology, Ref.[1] TEST SPECIFICATION A document prepared for each major test activity described in the Verification Plan task sheets with the objective to detail the test requirements, Ref.[1] TEST TOLERANCE The maximum range within which the test level can vary, Ref.[1] TETRA Technologien fr zuknftige Raumtransportsysteme; German programme TEX For technical textiles: the linear density, i.e. the mass per unit length. Also know as TITER TEXTILE For technical textiles: these can be woven, knitted or braided, or nonwoven products, [See also: WOVEN TEXTILE and NONWOVEN TEXTILE] TEXTURE Metal alloys: the influence of mechanical working on the microstructure of a metal, e.g. often seen as elongated directional grain structure TFE Tetrafluoroethylene TFRS Tungsten fibre reinforced superalloy Tg Glass transition temperature; the temperature at which a material changes from a glassy to ductile state, giving a steep increase in free volume THERMAL BARRIER COATING (TBC) Ceramic coating (often modified zirconia, circa. 0.4mm thick) applied locally to component areas experiencing high thermal flux and gas wash, e.g. turbine blade edges. TBCs are usually applied over an overlay (bond coat) on the substrate THERMAL CONDUCTIVITY Ability of material to conduct heat; the physical constant for quantity of heat that passes through a unit cube of a substance in unit time when the difference in temperature of two faces is 1 degree THERMAL CYCLING The repeated change of temperature experienced by a material, component or structure; the maximum and minimum temperatures are normally those associated with orbiting the Earth THERMAL EXPANSION [See: COEFFICIENT OF THERMAL EXPANSION] THERMAL LOAD (STRESS) 1 The structural load (or stress) arising from temperature gradients and differential thermal expansion between structural elements, assemblies, subassemblies or items, Ref. [5] 2 Polymer composites: One component of the hygrothermal load. The difference between cure and operating temperatures gives rise to in-plane thermal load for symmetric laminates, and to both in-plane and flexural thermal loads for unsymmetric laminates. The presence of the flexural load causes twisting of unsymmetric laminates after cure THERMAL MODEL Physical model fully representative of the flight end item in all thermal aspects, used for the qualification of the Thermal Design and for mathematical models correlation, Ref.[1] THERMAL SHOCK Sudden and rapid change in temperature, usually over a large temperature range THERMAL SOAK A period of time that a material, component or structure is exposed to an elevated temperature, e.g. structures underneath thermal protection systems THERMOCOUPLE Device for measuring temperature consisting of two dissimilar conductors joined at their ends which, when heated, develop a characteristic EMF. The temperature is indicative of that of the junction of the pair in the thermocouple, i.e. a point measurement device. Note: Calibration and compensation are required THERMOFORMING Processes that use heat and pressure to shape a composite component, e.g. applied to thermoplastic matrix composites THERMO-MECHANICAL An indication of the performance of a material under the combined conditions of elevated temperature and load THERMO-MECHANICAL FATIGUE (TMF) Mechanical and thermal cyclic loading experienced by a material or component. Note: Thermal and loading cycles can be in or out of phase with each other THERMO-OXIDATIVE Combined conditions of elevated temperature and oxygen THERMOPLASTIC Organic material, the stiffness of which can be reversibly changed by temperature change. One unique property of this material is its large strain capability, e.g. PEEK. On the other hand, processing requires higher temperatures and pressures than those for thermosetting plastics THERMOSETTING Organic material that can be converted to a solid body by cross-linking, accelerated by heat, catalyst, ultraviolet light, and others. This is the most popular matrix material for composite materials. [See also: EPOXY PLASTICS] THICKNESS OF PREPREG Usually specified as a nominal value in the cured laminate, when the latter has been cured to a particular value (often 60%) of fibre volume fraction in the laminate. Common unidirectional carbon-fibre prepreg thicknesses are: 50SYMBOL 109 \f "Symbol"m, 100SYMBOL 109 \f "Symbol"m, 125 SYMBOL 109 \f "Symbol"m and 250SYMBOL 109 \f "Symbol"m. Fabric-based prepregs vary in thickness over the range of 50 SYMBOL 109 \f "Symbol"m to 450SYMBOL 109 \f "Symbol"m, depending on tow size and weave type. The thinner prepregs are more difficult to manufacture and require low-filament-count tow; they are therefore usually more expensive THORIA [See: THORIUM OXIDE] THORIATED TUNGSTEN Thorium oxide dispersion strengthened tungsten alloy. Used in some lamp filaments and welding electrodes THORIUM (Th) Metallic element, melting point 1755C, density 11720 kg m-3. Uses: alloying additions THORIUM OXIDE (ThO2) Also called Thoria. Ceramic oxide used as dispersed particle reinforcement and as diffusion barrier coatings THRESHOLD STRAIN The value of strain level, below which catastrophic failure of the composite structure does not occur in the presence of flaws or damage THRESHOLD STRESS INTENSITY FACTOR [See: KISCC (Stress Corrosion) or (Kth (Dynamic)] TiAl Titanium aluminide; an intermetallic material TiC Titanium carbide TIG Tungsten Inert Gas; a fusion welding process TIME-OF-FLIGHT The time taken by a propagating wave, such as light or sound, to travel a known distance through a given medium TIN (Sn) Metallic element, melting point 232C, density 7310 kg m-3. Uses: alloying additions and soldering alloys TiO Titanium oxide TITAN Largest moon of Saturn TITANIUM (Ti) Metallic element, melting point 1670C, density 4540 kg m-3. Uses: alloying additions, class of aluminide. Matrix alloy for composites, structural materials for aerospace uses generally where operational temperatures exceed those possible with aluminium. Manufacture of structural shapes with superplastic forming/diffusion bonding technique, [See also: SPF/DB]. Extremely difficult to cast. Sensitive to presence of hydrogen and oxygen TITANIUM ALUMINIDE (Ti3Al, TiAl) Intermetallic material TITER For technical textiles: the linear density, i.e. the mass per unit length. Also know as TEX Tm Melting temperature at which the material changes from the solid state to the molten state, in C TM Thermal model TMC Titanium matrix composite TMF Thermo-mechanical fatigue TML Total mass loss. [See also: OFFGASSING, OUTGASSING] TORLON"! Polyamide-imide TOTAL MASS LOSS (TML) The total mass loss of material outgassed from a specimen that is maintained at a specific constant temperature and operating pressure for a specified time, Ref. [8] Note: TML is calculated from the mass of the specimen as measured before and after the test and is expressed as a percentage of the initial specimen mass TOUGHNESS The energy required to break a material, equal to the area under the stress-strain curve TOW A loose, untwisted bundle of individual filaments, usually identified by fibre type (in terms of fibre tensile strength and elastic modulus) and the number of individual filaments, often in terms of thousands of filaments TOXIC Substances causing serious, acute or chronic effects, even death, when inhaled, swallowed or absorbed through the skin, Ref. [10] TOXIC HAZARD INDEX (T) The T value is determined by calculating the ratio of the projected concentration of each offgassed product to its SMAC Spacecraft Maximum Allowable Concentration value and summing the ratios for all offgassed products without separation into toxicological categories, Ref. [7] TOXICITY [See: TOXIC] TPS Thermal Protection System (or Subsystem) TRACEABILITY The ability to trace the history, application, use and location of an item through the use of recorded identification numbers TRAMP ELEMENT Low level contaminant in metal alloys TRANSITION TEMPERATURE The temperature at which the properties of a material change.[See also: GLASS TRANSITION TEMPERATURE] TRANSITION ZONE Joints: the region between the parent parts in which the composition within the joint varies, e.g. between dissimilar materials in graded structures. The zone is of banded composition and often several mm thick to alleviate mechanical and thermal stress concentrations TRANSVERSE CRACK Matrix and interfacial failure caused by excessive tensile stress applied transversely to the fibres in a unidirectional ply of a laminate. This cracking is normally the source of the first-ply failure, [See: FIRST PLY FAILURE] TRANSVERSE ISOTROPY Material symmetry that possesses an isotropic plane; e.g. a unidirectional composite TRIAXIAL FABRIC Reinforcement fibres comprising of layers of biaxial fabrics which are joined together by continuous yarns TRR Test Readiness Review TsAGI Testing facility (Russia) TSNIIMASH Plasmatron test facility (Russia) TSTO Two-stage-to-orbit T-T Through transmission; an ultrasonic testing process using two transducers where one is placed on each side of the material under test TUNGSTEN (W) Refractory metallic element, melting point 3422C, density 19300 kg m-3, Uses: strength to extreme temperatures, reinforcement filaments in high temperature composites, alloying element in superalloys, tungsten carbide for tooling and high wear applications TVBO Thermoviscosity Theory Based on Overstress. Model for the analysis of fibre reinforced metals (MMCs) TVT Thermal Vacuum Test TWARON( Aramid fibre produced by Teijin Twaron TWILL A type of weave for a fabric, [See: TWILL WEAVE] TWILL WEAVE A type of fabric, generally 2x2 or 4x4, in which each warp end and weft pick floats over two or four crossing threads TWIST For technical textiles: direction and number of turns per metre TZM A commercial molybdenum alloy; typical composition Mo-0.02C-0.5Ti-0.1Zr U UD Unidirectional UHM Ultra-high modulus; a range of carbon fibres UK United Kingdom ULE Ultra low expansion (ceramic or glass material) ULSM Ultra lightweight scanning mirror; part of SEVRI on MSG ULTIMATE ELONGATION The elongation at rupture ULTIMATE LOAD [See: LOADS] ULTIMATE STRENGTH The strength corresponding to the maximum load or stress that an unflawed structure or material can withstand without incurring rupture or collapse, Ref. [5] ULTIMATE TENSILE STRENGTH (UTS) Highest stress sustained by a material before catastrophic failure. The ultimate or final stress sustained by a specimen in a tension test; the stress at moment of rupture ULTIMATE TENSILE STRESS [See: ULTIMATE TENSILE STRENGTH] ULTRA HIGH MODULUS CARBON FIBRES (UHM) A range of carbon fibres in which the tensile modulus exceeds 395 GPa, typically ULTRAVIOLET (UV) Zone of invisible radiation beyond the violet end of the spectrum of visible radiation. Since ultraviolet wavelengths are shorter than the visible, their photons have more energy, enough to initiate some chemical reactions and to degrade most plastics UMA Unfurlable mesh antenna; an antenna design from MBB UNAIDED EYE Normal Snellen 20/20 vision including eye glasses required to correct defective vision to 20/20 equivalent. Does not include microscopes, eye loupes or any other magnifying device UNDERAGEING A condition of a metal alloy stopping short of peak precipitation hardening UNDERCURING An incorrect process in which there is insufficient time or temperature to enable full and proper curing of an adhesive or resin UNIDIRECTIONAL COMPOSITE A composite having only parallel fibres UNNOTCHED STRENGTH The strength of a laminate without an opening UNSYMMETRIC LAMINATE A laminate without mid-plane symmetry USA United States of America; also denoted as US USAF United States Air Force USS Unique support structure; from Spacelab D1 mission UTS Ultimate Tensile Strength or Stress; [See: ULTIMATE TENSILE STRENGTH, ULTIMATE TENSILE STRESS] UV [See: ULTRAVIOLET] V VACUUM-BAG MOULDING A process for moulding reinforced plastics, in which a sheet of flexible transparent material is placed over the lay-up on the mould and sealed. A vacuum is applied between the sheet and the lay-up. The entrapped air is mechanically worked out of the lay-up and removed by the vacuum, and the part is cured. Note: Compare with PRESSURE-BAG MOULDING VADR Vehicle Analysis Recording System; X-38 vehicle VALIDATION OF PROCESSES A set of data (and/or experiments performed) to demonstrate that a process performs as intended (technical requirements) and that sufficient confidence can be placed on the outcome (quality assurance requirements). Process validation is approved by the final contractor VAMAS Versailles project on advanced materials and standards VANADIUM (V) Metallic element, melting point 1910C, density 6110 kg m-3. Uses: alloying additions VANISHING FIBRE DIAMETER (VFD) Model for the analysis of fibre reinforced metals (MMCs) VARIABLE AMPLITUDE SPECTRUM A load spectrum or history whose amplitude varies with time, Ref. [5] VAT-1104 Plasmatron at TsAGI test facility (Russia) VAWT Vertical Axis Wind Turbine VCB Verification Control Board VCD Verification Control Document VCM Volatile Condensable Material VDA Vacuum Deposited Aluminium VELCRO A textile-based hook and loop fastener. Registered trademark of Velcro Industries B.V. Venture Star An X-33 reusable launch vehicle demonstrator; from NASA/Lockheed Martin. [See also: X-PROGRAMME] VERIFICATION The verification is a process oriented to demonstrate that the system design meets the applicable requirements and is capable of sustaining its operational role along the project life cycle, Ref.[1] VERIFICATION CONTROL BOARD This board has the objective to assess/approve the status of the verification process including the approval of the verification close-out through the Verification Control Document, Ref.[1] VERIFICATION CONTROL DOCUMENT This document lists all the requirements to be verified with the selected methods in the applicable phases at the defined levels and traces during the phase C/D, how and when each requirement is planned to be verified and is actually verified, Ref.[1] VERIFICATION DOCUMENTATION Documentation associated to the verification process for verification requirement definition, planning, reporting and close-out, Ref.[1] VERIFICATION MATRIX Matrix associating to each requirement the selected verification methods for the different verification levels in the applicable verification phases, Ref.[1] VERIFICATION PLAN This document is the master plan for the project verification process and demonstrates how the requirements will be verified by a coherent implementation approach, Ref.[1] VERIFICATION PLANNING Planning phasing the verification activities with the project milestones and programmatic constraints, Ref.[1] VERIFICATION REPORT This document is prepared in case than more than one of the defined verification methods are utilised to verify a requirement or a specific set of requirements. It explains the approach followed and how the verification methods were combined to achieve the verification objectives, Ref.[1] VERIFICATION STRATEGY The verification strategy identifies, for each requirement category, the applicable verification methods at each level, together with the models involved in the verification activities. It assures consistency between the several verification activities at the different levels avoiding duplications or gaps in the entire verification process, Ref.[1] VERIFICATION TEAM Dedicated team, within the project organisation, responsible of the verification process particularly in terms of co-ordination and results, Ref.[1] VERIFICATION TOOLS Tools utilised in support to verification implementation, e.g. Ground Support Equipment, Software Validation Facility, Special Tools, Simulators, Analytical Tools, Integration and Test Equipment/Facilities, Ref.[1] VERY HIGH STRENGTH CARBON FIBRES (VHS) A range of carbon fibres in which the tensile strength exceeds 3500 MPa, typically Vf Volume fraction of reinforcement fibres within a composite material, expressed as a percentage VFD Vanishing fibre diameter. Model for the analysis of fibre reinforced metals (MMCs) VHS Very high strength carbon fibres VISCOSITY 1 A measure of the fluidity of a liquid, in comparison with that of a standard oil, based on the time of outflow through a certain orifice under specified conditions, Ref. [10] 2 The property of resistance to flow exhibited within the body of a material, expressed in terms of relationship between applied shearing stress and resulting rate of strain in shear VOID Air or gas trapped in composite materials during cure VOID CONTENT Volume percentage of voids, usually less than 1%. The experimental determination is, however, only indirect; e.g. calculated from the measured density of a cured composite and the 'theoretical' density of the starting material. Such determination also implies that voids are uniformly distributed throughout the body VOLATILE CONTENT A measure of the mass loss from a sample subjected to prescribed test conditions. The volatile loss is an indication of the solvent content of the prepreg remaining from either the resin-compounding process or a solution prepregging operation. Prepregs with a high volatile content tend to produce heavily voided laminates, owing to the vaporisation of the usually low-boiling-point solvent within the resin constituent during cure VOLATILES Materials in a sizing or a resin formulation capable of being driven off as a vapour at room temperature or slightly above VOLUME FRACTION Fraction of a constituent material based on its volume; a measure of the quantity of one phase in a composite material, usually the reinforcement fibre content, e.g. denoted as Vf and expressed as a percentage VULCAIN Ariane 5 main cryogenic engine VUV Vacuum ultraviolet W WAISTED A type of test specimen or coupon where the gauge length is not parallel for the entire length WAKE Behind the direction of spacecraft motion WARP 1 The yarn running lengthwise in a woven fabric; a group of yarns in long lengths and approximately parallel, put on beams or warp reels for further textile processing, including weaving 2 A change in shape or dimension of a cured laminate from its original moulded shape WASA Wide-angle support assembly; part of the Mars Observer Camera WASPALLOY Nickel-based, chromium, cobalt and titanium containing, high-temperature alloy (UNS alloy designation N07001) WATER ABSORPTION Ratio of the weight of water absorbed by a material upon immersion to the weight of the dry material. [See also: MOISTURE ABSORPTION] WATER VAPOUR REGAINED (WVR) Mass of the water vapour regained by the specimen after the optional reconditioning step. Note: WVR is calculated from the differences in the specimen mass determined after the test for TML and CVCM and again after exposure to atmospheric conditions and 65% relative humidity at room temperature (22 3)C, Ref. [8] WAVE SOLDERING A process wherein printed-circuit boards are brought in contact with a gently overflowing wave of liquid solder which is circulated by a pump in an appropriately designed solder pot reservoir. The prime functions of the molten wave are to serve as a heat source and heat-transfer medium and to supply solder to the joint area WAXS Wide angle X-ray scattering WEAG Western European Armament Group WEATHERING The exposure of plastics outdoors. In artificial weathering, plastics are exposed to cyclic laboratory conditions of high and low temperatures, high and low relative humidities, and ultraviolet radiant energy, with or without direct water spray, in an attempt to produce changes in their properties similar to those observed on long continuous exposure outdoors. Laboratory exposure conditions are usually intensified beyond those in actual outdoor exposure to achieve an accelerated effect WEAVE The particular manner in which a fabric is formed by interlacing yarns and usually assigned a style number, [See also: PLAIN WEAVE; SQUARE WEAVE; TWILL WEAVE; SATIN WEAVE; BIAS WEAVE] WEB A textile fabric, paper, or a thin metal sheet of continuous length handled in roll form, as contrasted with the same material cut into sheets WEFT The transverse threads or fibres in a woven fabric; fibres running perpendicular to the warp. Note: Also called fill, filler, filler yarn, woof. [See also: FILL, FILLER] WEK Waddoups, Eisenmann and Kaminski; a fracture model WELDING A fusion joining technique involving the melting of both joint materials, often with the addition of a third (filler) material WET Having absorbed moisture. Like the presence of voids, a uniform moisture distribution is implied which is unlikely to exist in reality. Most absorbed moisture is located near the exposed surface. Interpretation of the effect of being wet must take into account the realistic, highly non-uniform moisture distribution WET LAY-UP The reinforced plastic which is liquid resin applied as the reinforcement is laid up; the opposite of dry lay-up or prepreg. [See also: DRY LAY-UP, PREPREG] WETTING Flow and adhesion of a liquid to a solid surface, characterised by smooth, even edges and low contact angle WHISKER Reinforcement in the form of very short fibres, usually crystalline WHORL Coils of reinforcement fibre that form in a prepreg sheet; usually occuring at the end of production prepreg runs WINDING ANGLE In filament winding, the angular measure between fibre (filament) direction and a reference axis (longitudinal axis or axis of rotation of a cylinder or a pressure vessel) WLC Winged Launcher Configurations WLE Wing Leading Edge WN Whitney and Nuismer; a fracture model WHLER CURVES A graphical representation of the fatigue properties of a material, where stress is plotted against the number of load cycles to failure WOVEN FABRICS Fabrics produced by interlacing strands more or less at right angles WOVEN ROVING Cloth or fabric containing reinforcing fibres WOVEN TEXTILE For technical textiles: these are fabrics constructed from visually identifiable, compacted bundles of fibres known as yarns, [See also: YARN] WRINKLE 1 A surface imperfection in laminated plastics that has the appearance of a crease in one or more outer sheets of the paper, fabric, or other base which has been pressed in 2 Sandwich panels: deformation of the face skins; a potential failure mode WROUGHT METAL PRODUCT Metallic stock material, e.g. in the form of sheet and strip, plate, bar, which is produced by methods involving large amounts of plastic deformation (such as forging, rolling, extrusion) that results in a material with a wrought microstructure, often with some level of anisotropy Wt% Weight percent WVR Water Vapour Regained X X-30 National aerospace plane (NASP) X-33 Venture Star. A half-scale, sub-orbital experimental flight-test vehicle designed to demonstrate key design and operational aspects of a single-stage-to-orbit (SSTO) and reusable launch vehicle (RLV) rocket system; from NASA - Lockheed Martin, (USA) X-34 The reusable launch vehicle (RLV) technology demonstrator vehicle: small, fully reusable vehicle from Orbital Sciences Corp. (USA) X-37 Future-X Pathfinder. An unpiloted reusable vehicle, carried by Space Shuttle, for both orbital and re-entry technology tests X-38 The re-entry demonstrator Crew Transfer Vehicle (CTV). A forerunner of the Crew Return Vehicle (CRV) for the International Space Station (ISS) of which European participation is through the German TETRA/X-38 technology programme X-40A Space Manoeuvre Vehicle. 90% scale model, free-flight tests X-43 Hyper-X Scramjet Demonstrator. Test vehicle(s) for single-flight missions at Mach 7 to Mach 10 XMM X-ray multi-mirror telescope X-programme The US programme covering future reusable space-vehicle concepts, i.e. potential Space Shuttle replacements X-vehicle A series of experimental vehicles designed as ground and flight test beds for proving technologies required for future reusable space-vehicle concepts; under the US-instigated X-programme Y YARN For technical textiles: a continuous assembly of twisted filaments, fibres or strands (natural or artificial), suitable for processing to form a textile, e.g. by weaving or knitting YIELD STRENGTH The strength corresponding to the maximum load or stress that an unflawed structure or material can withstand without incurring permanent deformation, Ref. [5] YIELD STRESS (YS) Stress at which permanent deformation commences in a material. The limit of reversible elastic behaviour, [See also: PROOF STRESS] YOUNG'S MODULUS The ratio of a materials simple tensile stress, within elastic limits, to the resulting strain parallel to the direction of the tensile stress YTTRIA Yttrium oxide (Y2O3) YTTRIUM (Y) 01abcdm b m  +,TUlmno헛~z~~z~ohMVh%CJaJh]f hMVh%jhMVh%U h7h%h,h%hh,mHsH hh hh8 ThDh,5 h]f@hh,@jhh,@U jhh,UmHnHu hh,jhh,U)cdm b m g  +n "$Ifgdgd%gd, gdXsgdD$gdDgd|{]gd]fgd,gd, B/=zuuuupkkkgdAegd4CQgd]fgd,gd,gd%vkdY$$IfF0 # 064 FaFyt]f  !"<=>?@ABCD`abcopqигَzгoَj[h]uLU'j%[h]fh]uL>*B*Uphh]fOJQJmHnHsHtHjZh]uLUjh]fU h]f'j+Zh]fh]uL>*B*Uphh]fh ah]f0J,jh ah]f0J,Uh4Cjh4CU hh, hh%%   '֘wgbXbjh]fU h]fh]fOJQJmHnHsHtH'j]h]fh]uL>*B*Uphh]fh ah]f0J,jh ah]f0J,Uj\h]fh]uLUjh]fh]fUh]fh]fj\h]fh]uLU h]fh]fh]fh]f0J,>*B*ph%jh]fh]f0J,>*B*Uph'(),-./0=PQGH78HIUV`kX#Y#+ȸ||uumh}h4 H* hh4 hEsh4 hh4 h4 h- 9hAe h- 9h- 9&hAeCJOJQJaJmHnHsHtHhAeh4Cjh4CCJUmHnHuh]fOJQJmHnHsHtHjh ah]f0J,U h]fjh]fUj]h]uLU*BPQXgkd^$$IflF@#N t6    44 lalytt "$IfgdtgdAe "$Ifgdtgkd^$$IflF@#N t6    44 lalytt7G "$Ifgdtgkdo_$$IflF@#N t6    44 lalyttGHO "$Ifgdtgkd`$$IflF@#N t6    44 lalytt8H "$Ifgdtgkd`$$IflF@#N t6    44 lalyttHIP "$Ifgdtgkdya$$IflF@#N t6    44 lalytt "$Ifgdtgkd'b$$IflF@#N t6    44 lalytt0INVakgd4 gd4 gd4 gd{gd4Cgkdb$$IflF@#N t6    44 lalyttz>JT_ pt:Q"&gd4 gd4 &>D+4G P !!L!a!!!" "w"}"""W#Z#w#}#gd4 gd4 }###$$E$I$_$m$$%%%a&''((())),)1)i)n))))gd4 gd4 ))))))#*)*A*K****+++,,T-X-j-q-----..y.gd4 gd4 +,..11{A|AdIhII JJjJrJKKcLqLWM_MMMOP;QTTaavbwbbb3l7loott؎ڎln=jh@h4 Uhkh4 H* hkh4 h4Ch4 mHsHhkh4 H*h>h4 H*h>h4 H*h>h4 mH sH h>h4 hh4 h}h4 H*hDh4 H*h4 h}h4 5y..t//000112"22223344556666k7~778x8gd4 gd4 x88889 9R9`999":':W:[:w::;;';+;j;<<<V=f=>>?gd4 gd4 ???@#@0@@@@@@AzA}AAAAAAB-B?BBBtCyCCCCgd4 gd4 CDgDkDDDDEE FFuFFEGVGGG9H=HQH_HHHeIhII JJjJgd4 gd4 gd4 jJrJKKcLqL=MAMWM_MMMOOOOPP;QAQoQSRTTT=UBUrU}Ugd4 gd4 }UUUYVpV WX0YHYYZZZN[T[[[\\M]\]]]3^9^^^^^gd4 gd4 ^ __1_;___o`|`hanaaafb{bbb6c:c}ccPdYdVe^e ff0f:fgd4 gd4 :fffAgJggg(h,hLhUhiii,j=jjj)k8kkkll4l7l;l{llgd4 gd4 gd4 lllmmo!o`omooopp.p:p\qcqqqqrssztttt=wKwgd4 gd4 Kwww/x6xxxOyYyyyyyzzzzz{~{{{||}~~gd4 gd4 !7=^dӀ؀BJ΁"(MQns gd4 gd4  7;Wc+L6lPSʼn/9MSgd4 gd4 Sptƌˌ9=]eZr{N}gd4 gd4 }ޓ"( o}COݗ6V",Ka"Dgd4 gd4 D_J%Ġ=Káܡ5N}'3dpgd4 gd4 R\'ǧ6@y|=Agd4 gd4 m!үׯ'ͱ߱`o'/Wogd4 gd4 #$%&12YZqrܳݳ -./MNw013ŽŽŽŽŵŵŮţţsţdsjgh4 UmH sH hF'*txgd4 gd4 gd4 }33rrssyyyy܆ކhlXZ\},.np_c|}~$h!]%h4 H* jDhh4 hx*h4 H* jh=*h4 H*h4Ch4 mHsHh[Rh4 H*h:h4 6H*h4 OJQJ^Jh7OMh4 H*hDh4 H*h7OMh4 H*hDh4 H*h4 hh4 2*/"&apu 5:U]bggd4 gd4 1A=I7Hb".PUy}gd4 gd4 %<  ;!?!!!#1#"$B$%%&#&&'''3'8'gd4 gd4 8'U'Z'}''((((1);)*&******* ++)+-+C+P+++],f,gd4 gd4 f,~--/.3.L.P.e.j...../ /J/N///// 00,030P0_000gd4 gd4 000 1!111)212T2^2~3333334S6~67,7F78888819gd4 gd4 gd4 1989998:C:;<<===>>>>x?@ @#@,@@@AAAjByBBgd4 gd4 BBwCCC>DUDDDDDjEnEEEEEEE&F)F8FQQQ"RNR]RSSZTyTTTeVvVVVWWWWWWWXfXXgd4 gd4 XXYYZZZZL[Z[[[]]^ ^^^(_._[_n_``aabbLbgd4 gd4 LbQbc)cccVd]dddee ff@gMgggh"h=hChdhjhhhhimiigd4 gd4 iiajdjrjwjjjjk3k7kTk`kkkk]lclull1m5mZmammmnngd4 gd4 nnnnnoonoop,ppp>uCuuuuuuu vv,v1vzv}vvvgd4 gd4 vvvvvwwMxaxxxTycyyyyyyyyzzA{F{a{i{{{{gd4 gd4 gd4 {{Y|\|o|t|||R}]}}~ ~~~ Qb#$|gd4 gd4 |$TcQnЅquW[txgd4 gd4 L\?Egk*.HLilyBIÍS]Վ3Cgd4 gd4 gd4 Ώӏ #AT&`*2drޓ>ǔgd4 gd4 ǔ̔-F7b}%FS\x{әڙ w}Ûgd4 gd4 Ûћ;G',x ,I%2֟ܟ-1FJkpgd4 gd4 )1ءۡȢţJ uĥ֥ק.S|MXgd4 gd4 Xݪ*qu~׫ګ 28w}Ŭʬgd4 gd4 gd4 @G9MQptFJҰ(fgd4 gd4 fodzjeuҵٵ۶*  +gd4 gd4 +-30p|`je'wgd4 gd4 w`Gl!6@sy+6gd4 gd4 OTs}-1JNt~!9=jogd4 gd4 oaevz5;keL\gd4 gd4 gd4 HMmq^d|:Ahl%V_gd4 gd4 gd4 }x;a}GK_fqxgd4 gd4  !%<Aae=AQTdhgd4 gd4 hx|_k ,gE]GKqugd4 gd4 $&12st+,-<=PTAkm  44M:N:==@@@@@@&BKBFҾҾ~h,h4 mH sH h,h4 H*h!]%h4 H*hDh4 H*h!]%h4 mH sH hh4 jhh4 Uh!]%h4 0J,jgh4 Ujh4 U hu h4 jhu h4 U jhh4 h4 h!]%h4 H*.u.<o D>P%3w gd4 gd4 CGfj!nsQTWgd4 gd4 gd4 AFq@Q#2 37j - 6 gd4 gd4 6     X n  2 -L['E;Jygd4 gd4 9A37~%5yaogd4 gd4 f  7 ; J O t      !gd4 gd4 !!"$$%%%&9'H'' ((((((( ))%)*)K)S)))))gd4 gd4 )2*6*M*R*****<+@+X+\+q+y+q,y,,,z--..F/W/////gd4 gd4 /0011m3y3344455(6.6C6^678;8N899,:0:J:O:e:l:gd4 gd4 l::;p;;;;l<<<<<<<<==$='=9===X=]======W>gd4 gd4 W>j>y????0@4@E@H@@@@@@AAAAAA&B1BEBJBBBBBgd4 gd4 gd4 BCCC CWC[CCCCCCDDDEEnFqFFFSG_GH,HHHHHgd4 gd4 FFGG'H(HGIHILL[[aaaaaaa,o0ooo-|.|=|>|?|@|I|J|d|e|z|{|||bd׍؍ѽ𲫖ykjh4 OJQJU^Jh,rh4 H*h,rh4 6jjhwch4 EHU)j]A h4 OJQJUV^JnH tH  h@h4 jh@h4 Uh[^h4 0J,jRih4 Ujh4 U hh4 h,h4 H*hDh4 H*h4  jh[,h4 H**H@IIIII|JJJJJKLLLLLMMMNO}OOO PiRRRMTgd4 gd4 MT UUVoVVVV WhWyWWWWTXfXYYYZZZZZC[H[[[[gd4 gd4 gd4 [[[[[\\.\3\\\\\\]J]P]u]]]^^^<`@`U`Z`|``gd4 gd4 ``````aa'azaabbYc]ccc%eCfTfffff gggg[hgd4 gd4 [h_hhhhhhiii9i?iaiei~ii;jhjj+k3kkklllmPmemgd4 gd4 em n1n-o0o4o=o@oSoXo~oooopp5p9pfpEqIqqqqqr"r.r}rgd4 gd4 gd4 }rs(sttdujuuvvvwwxxxx3x7xQxUxxxyyuy~yjzzgd4 gd4 zzz{&{{{+|A|H|c|y||||||}}B}F}Y}h} ~~.~3~R~s~gd4 gd4 s~il y#‚ƂBNЃփ/݅gd4 gd4 @fW_Sa‰Ɖ։ډJS!,cggd4 gd4 gyӍ XڏÐ͐CNԔ*gd4 gd4 ؍  JKL CD sf__TMT hu h4 jhu h4 U hh4 jnhUh4 EHU)j|!H h4 OJQJUV^JnH tH  hUh4 jhUh4 UhUh4 6OJQJ^J jehUh4  jnhUh4 h4 jh4 OJQJU^J%jUlh>"wh4 EHOJQJU^J)j|!H h4 OJQJUV^JnH tH h4 OJQJ^J*3Ӗ>G\iϙؙc>UjnÞE]gd4 gd4 kLۢˤФN]TtaêQޫgd4 gd4 {+3ήҰ&=ae2gd4 gd4 26NRu~txĶ϶·Ʒطܷ {Ѹgd4 gd4 ѸRj{|ʺκ/3HKae/tgd4 gd4 gd4 [p̽&:ӿڿ  LV"gd4 gd4 gd4 #d  ,ei0>{gd4 gd4 {[rn|lsR^h} #( gd4 gd4 %l  gd4 gd4 FI[hMZ37HLgd4 gd4 [\]^TUhijktuv"(: <        ( xmh h4 mH sH hmh4 H*hmh4 H* hh4 hXd.h4 6H*hXd.h4 6jphDm^h4 EHU)j-D h4 OJQJUV^JmH sH jh4 UhXd.h4 H*hm_h4 H* jwhm_h4 hm_h4 6OJQJ^Jh4 hVOh4 H*'  $<@v Rlt#$gd4 gd4 $%(.io"hlMTgd4 gd4 gd4 sy/4QVjsgd4 gd4 "15RW8 (gd4 gd4 (;\`_p1*[u /ouxgd4 gd4 x|JM       % O W      gd4 gd4   ( 5     ZeSZ+/-gd4 gd4 ( 4 5 r t       35ijkJ%K%>WBWZZ^^Dg\g]ggww)w*w0w1wGwHwOwPwfwgwpwqwwwwwwwwwwxyy铌铌铌铌铌铌 h@h4 jh@h4 Uhmh4 mH sH hh4 jDh4  jah h4 h h4 H*h;h4 H*h;h4 H*hmh4 H*hDh4 H*h4 h h4 mH sH h4 mH sH 7-w fm <B)-1]gd4 gd4 ]bVn  2 = !6!!!I#O##$$gd4 gd4 $0$7$$$$$:%N%%%&&&&5'<'l'q'''(%())**/+:+gd4 gd4 :+++ ,,F,S,,,----------..!.%.<.A.W.r.//gd4 gd4 //00001$1D152B23333l444445556666?7L7gd4 gd4 L7>8K8899&989{99!:4:::;;|<<< ==A>>>h?y?? @hAgd4 gd4 hAuAwBB(CDCiD{DDDOFcF-GDGmHHI$I@I^IIJJJKKCLMLLgd4 gd4 LLMMOMMM7NANN?OHOPPPPQQbRtRRRSS/S3S=SCSSgd4 gd4 SSS9T=TPTUTTTTTTT$V+V?WBWDWWW[WwX}XXXY*YZ)Z\Zgd4 gd4 gd4 \ZjZZZ[[[B\F\^\b\s\v\\\\\])]]]]]k^t^^^X_]_gd4 gd4 ]_x_}_```0aCa"b=bbbqcc1dGddd8eWeFfYffgDgKgggggd4 gd4 gg}hhii*i/iTiWiijj kkkllll9mmmnnooppgd4 gd4 pppqqr|rrrslssss t&u4uv-vxxxxFySyyy,z=zgd4 gd4 yyyzz { { {{S|U|||~~@B͕ߕ24ƥǥ 389;hlce +ɾ hmh4 hGh4 H*UhGh4 H*hC[h4 H*hC[h4 H*hy'h4 mH sH hC[h4 mH sH  hh4 hh4  jhzh4 H*h;h4 H* jDh,^h4 h;h4 H*h4 4=zzz{{M{Q{b{f{{{||||||||x~~~~wzgd4 gd4 0\nxтՂ;Rjs9Gmgd4 gd4 eu)KQdhgkgd4 gd4 hn@CRVÎ׎ ܏gd4 gd4 gd4 :KGK?K%>fy04gkʕ͕gd4 gd4 gd4 TYOoę >C^b}šƚAgd4 gd4 AN\zv.̟ޟ#E[̣atKrťȥ'gd4 gd4 ',a VcakȬЬ qvbgd4 gd4 gd4 br &crٲ޲ EJ,4gd4 gd4 ^dֺɻͻݼ&kgd4 gd4 ̾<A;@EJ/5qvnx4gd4 gd4 gd4 458=8Hilx!+ gd{gd4 gd4 gd4 Metallic element, melting point 1522C, density 4470 kg m-3. Uses: alloying additions, ceramic compounds Z ZERO-BLEED Prepreg materials that contain resins with viscosity and gelation characteristics optimised to avoid excessive resin flow during processing, [See also CONTROLLED BLEED] ZINC (Zn) Metallic element, melting point 420C, density 7130 kg m-3. Uses: alloying additions ZIRCONIA Zirconium oxide ZIRCONIUM (Zr) Metallic element, melting point 1855C, density 6510 kg m-3. Uses: alloying additions ZnO Zinc oxide References Alenia Spazio, Italy Review and Improvements of ESA AIV Guidelines: TF/DM/9352 (Aug. 1984) ESA/ESTEC Contract No. AOP/OL/RB/324147. ESA PSS-01-80 Issue 1 - Draft (Sept. 1994) G.F. Dieter Mechanical Metallurgy. McGraw Hill. ISBN 0-07-016891, 1976 D.R. Lide, Editor in chief 'Handbook of Chemistry and Physics' 72nd Edition, CRC Press Inc (1992) ISBN-0-8493-0565-9 M.H. Weik Fibre Optics Standard Dictionary Chapman & Hall. 3rd Edition (1997). ISBN 0-412-12241-3 ECSS-E-30-01 Space engineering Fracture control; previously ESA-PSS-01-401 ECSS-Q-70 Space product assurance Materials, mechanical parts and processes; previously ESA-PSS-01-700 ECSS-Q-70-29 Space product assurance The determination of offgassing products from materials and assembled articles to be used in a manned space vehicle crew compartment; previously ESA-PSS-01-729 ECSS-Q-70-02 Space product assurance Thermal vacuum outgassing test for the screening of space materials; previously ESA-PSS-01-702 ECSS-E-30 Part 8 Space engineering Materials ECSS-Q-70-71 Space product assurance Data for the selection of space materials and processes; previously ESA PSS-01-701      DOCPROPERTY "ECSS ID" \* MERGEFORMAT ECSS-E-HB-32-20 Part 8A  DOCPROPERTY "ECSS Date" \* MERGEFORMAT 20 March 2011  DOCPROPERTY "ECSS ID" \* MERGEFORMAT ECSS-E-HB-32-20 Part 8A  DOCPROPERTY "ECSS Date" \* MERGEFORMAT 20 March 2011 ECSS Secretariat ESA-ESTEC Requirements & Standards Division Noordwijk, The Netherlands -v0T>r+gd4 gd4 7gd]f+#$1245]^uvxy !ϾϾ櫝h!h= hfh4 hEt|h4 h4 h{h4 hAeh{jh{UhAemHnHuh{mHnHujh{UmHnHuh5wjh5wU hhS hEsh4 .34xkGC$Eƀ-Ɔgd{GC$Eƀ-Ɔgd{xgd,gd, $dNgdI5<FEƀ-Ɔgd{ !gd4 9 0&P 1h:p{. A!"#$% nq ,@:Q|)PNG  IHDRPB`PLTED5W .k=}M']4mC|D}Tg|ҒܫibKGDH cmPPJCmp0712Hs IDATx^[z: ,\ ^,9k&Fe9}^ Qa@99\#ʷ_b9l Bwr)P,Ra3r.P, [<_R[ OO\&A"ӳQO7bI9E(/%U$^ a)(WAyy&QJbq%/>Ba(u(O9Oߪ=a(pQ];=idp-e?"a7x ڬ( sY RtvxLTڸ=pݏ1,q$,-|}$NɎk29#5`Y#{H8y<;|61pPd5CIMf`fE 4V1ާ'G@@>8آ-fw!wH#lH,YqK(oOl>bn7a3[z ̂ܝKVG%ZWKQ@ΥdT^H:Qm%:0gZ<8Y۞s@[y)Y h0EzʏVbc^K =7C*Rz}%7 (kYlX--$JQ=ElSfbQ_lҥYX+zݽҭ$,EfV޻ n`-]ޮVpnXi0A9,E )PNGsfaP [lu}xRbCY˲i8diyP ;m2?Hbء`Ά,w}jyU\eqn7JC].>}"u}J:ލUn"he ɽq%aJHhA%:]%B MPw+N ba}Ng]jNXy }lf+2̞f1G}(#EO ˲DjaZ?eXҔ-;X}p$,!֟Z3&Oe롧Z!3$Yi/ 3jYwiHޕ;]CEt&JebM%tHۖKQ~Kjr1]QhѯkUA`)Ԭv X:AsݑVɜ(So~"[ :YR?A@`Eڈ^%N8Kgdō/I˷) _>Fm?9"\)K86Y_aL3thA~VĈr,AΚR鏶V7H݁3fh HXCVpl@ALcGWZ((oqH`:C*JqZ-u4E%j^/a.,oHxcz7琰8-ϱ39% oǻ%u &#-61a%Δ%f"ZXB)>T@.UǼHzݥ1a%azP ~FtSYГPGھ_1@B?*,ekFUnc: g(7khc.g{6󞄃1p-%2JݳѦPdVd:}:/Vkρ.yWO V!DMxÄeH)/aIr')/m)(F%9U]W1"HXBI&َ)ih5(ׄ5I4^?ŽU@Ѭ$}e3R8X7VW٣F?)6x= / {ZkQ}/kwXѭdrzQ^ 6'ŷ}Vx{?W!&G;>)xĿ|c^4v'lѿ:Wkn846f| g'Xj|ڟſ_店+sSŞ9`ؒ3j3l׌Q⯋7?f͛|^ӤhqB0Ӱ~:bGkmH!n>:WrlCI*ߤR_;hғ=n/7G l2\l~ 7'@ȷso/o X"KE8/^W:%{eOs D j#VM'@Lvga-&WJ+vv_3~^+Y%ů<5wi:IGGS0>AfK7<^ǹa'4]0>8> hq4OA * ˊOs|PK_jڿ"\$A$lF/<#炗+?E}׺>6IhEO*<+zFv/Mbkb5q#f?ou▟"#.3ש^k;?G¯4_L(t]O+o?=y/;ux➣kxx \Gs4%s<=E}CȒ"I+Ђ:O_rŭMKZLdgA_;+\g^7xvuHIG ]gފ(4aEPEPEPEPEPEPEPEPEPEPEPEPEPEPEPEPEPEVu+M"{lC$#P2K1_&|Kn-vO Ek(wLxhVԨԬq\cRT N>2~ >]i-IFLkn#yqt $|͞z/k7"HDŽ<#(RGJo߳g_:lV𞟧*-aLĉ۰rt5ڼ~ M{\_^QI⦕.U{_GvzEJ-XP J(6Ռ(@q?~(|!5.7Ljlµqj}Y;s_ )uMcRp'՟̾\A6g1IצԞ-Ɵt(g Zl7'I{#WlSES pu/"uK;lFYm ;dE<:+MN߂lѮka#w %]5m},9U>ڿ-焪ͣoo]]]ueY9B=T?)1|y~ވS2jx/? põ{e~W~qdľ@ d?yvYTkXToJ|WT-%&]Q]ӟNh$\y/۶kQ*e{28\ pnlʾk]#Ffvl 33lEqwqQH((((((((((((((F`@Oj/?'?vxdFJI%91kNX+g5Vy&"(I<_%|Di)[ SL`$.9\Ϳ"?x+m᩶eO!neNھc7Bӣnu$W-.oG#hOCƳ\X}|ቍG^d885O~=Gx;: *-A^LwxI¥yVn˲}`+aEPEPHsgyJkn|HRI"|ɤO)}ZTV\_!t ٮ^ o!~hByONd||QO˨|۷bSw力K/hMBWeI4!y r^_aiZ6Jݶ&& 2qԝ.T#u9`Zv㌟¼]v;mw$vK3.ir E#Q@WNNdH*xϵ|)|`*}WUugpZ}Yv9MZjAʢm>Wd֛oD|rF$ͮt]{}!;; jiY, ړ(;sۚ|9ׄ[_h}boݝCSו|a\\hOYH4&5{٦ٱs4?tWf m[Ɲ^^WzԒRfݮv>/m*dHRGXszWc8hc.9~uf9|q{.Udܿ-P}]{<2̍Rҿi|%>]So{e mx~ux cqdesV|S?oxWmko\y*1'VrG8FSUϣl_͟ |GfRm'I菒5 =j_;xƸ@FS?yς^-'ua8?|+K|Ѐ<+ӨFO^|+aEPEPEPEPEPEPEPEPEPEPEPEPEPE$Hci$eDQf8z@5D ||gb[巰.;/K[7L|Gn|Cr;]<28]/?WHOdU'Ma4K{6+m$v ]ʄij]_|yo 6 O4j]/ho@" /=ox?EHod\]jGͼl *}543yS%:j󂷧i?%9ɢxΣ:^out>-$ d7C)~xMK:%̗IN1Z_{ Đim-sxb,!Q>=_|5~Xiq/ʙa#Itѧ, 4nqԞ$$ܥm/s$qJc!@z \ɚ™r=|Fm[^#m[,q\F2NG\M>j|;}kI :$ȓ)8G=0z᫑(>UR h&Ӌ׵_߇W7h֖2/xڪX\ *[9 ;u-8)ƣ׼VUF%Q=NӧM[ҭnp>Z¾1O,w@o,d x2 /8#$S~ 1[|M״.T[}n#g̸\ *fxj>*{=0厡EVG@QEQEQEQEQEQEQEQEQEQEQEQEQEQEx'?^xopӖ_U>^}=q;LsڴNUev|U?/5}KRCJ| v=2c|$ a0WR# xB x3FGҢ;29kE)9>i;QREPEPEPEPEP_P|4GW170j睸|wE|Znl>$;Nn:g]'(/:7ÿ)).ͱVYH=AF)VjJM+=?dRK2yZV|;K-=<,ީaӺwjIweՆD_I8$V5KڔLE}rUWQO]r*RZ<kʃG(!ByS ᄋ ɮ^;7@rWG5'1_Q Lo4R`†Px_هoĽaͷм:Cs )79xVͩB$F`1w=:^-鹰dt ʗ#V"HRhu#\@#ٸ{jkK=@J]&T1g5?oĝ[K o@n%X~!gp9*R.Yiԟt_¥zO-4k[j7ԓ>>~β|T'U$<ζJ mh}amx3w6<ZHpA SH$z׻ן#RHr7z^/v}6U+ 5WS8V}l-a$c TQ_$}QEQEQEQEQEQEQEQEQEQEQEQEQEQMD6FTEfc5'__~sFc xW8h{/z(ѕgn! bj~| ~&̅.n!AHt/weTߌI kglc@ORI'ZVJV0H(QEQEQEQEQEQEQEQEQEQEQEQEQEQEQEQEQEQEQEQEQEQEQEQEQEVҼXhz%fa minR$׹5NoihZ+eAEW0Š(((((((((((((((((((((((((+S?7A|PDQc_W'5NUfly/O_Ň>_=_ƾ)l?58ǡIz wt[ONѴqƃsN3I5~?^4|6M"Q&]9O?RX(M{Uo^lRWQE0(((((//|뻈b2gɩnfXǩjZǤF#M2H+JpP&{8fϴk:ynEg!Ҭ ;8'RE%+z 5߃K߇I|4MjnԤ8xцI$ +(z鶷:9 "K HHxs]NjEzW>t>q֣im1Q= fVn:t8 ڼĞTڎi7wJ+7cR9_/x> oş"__DЮ :ScdBiA%[>0{~>ڎ߰K,2,8ʺ0*GB5}Z{ѣF|Ie|->~P2^7u di#68,q5~ 7lu=>×0tmro]NOQ>״6_*QO:c-{ I.m綏;Ud\rrbA7?k_GtcΉ>&Mt$@AF|ŝKg^Ф>/^óG~x0YH "099}]r}Zmo.}P|_i}?8'%Xe]2E~|~>Ѽwᶽm. xX.lcQ-S%UNI+Mr~5½\ˍ/gX,0'YOg"u r'=&D.XAlu;=N#-qHA_4?E$߲wm{sq& g,ŏ\zs^Inqj/Ƙeҵ|$,M}[ޜo m3-u [,cuv}jxÚ~ 񎝤~".Zx * |ԿƻХο3ŦJ2y;l9 79cc*pנwiZ\6rYdUs2-&@탟xDŽ?f]֕☣u{S.MO-۠'XHB`sd_^\<[>Gέ),1c#vAR-ӧ8\K3  )_qRz͆ ˨_[XDfXԟLƻ;aNZ蚍嶪YD$Tp 4nP8[ 0xuI˙Co"X$$(J z~;ϣ!լn4yo-iITŴu;*^)f"WW8T[, ^嗀OZ<67ÿ $sç }/>#\P؋=+7;=KB||?u?>"dn4mӮnrܸR RIqRUϾu3NwZN4Yfζ"a @NӴ tmk@>! aX /#<Ϙ5_>JOg{Y,.K8E9*%B1{繏heFnI֨ A=~k:RM&o^xϭ!B(GpH $[" F~;/\xRmżZ<0@#M5%zup ޓG bb8#5-АmkOR coך_V~ OkGWAn_ ~ZMy1jĺyq8$qG/=oŅϦ4izِiڕYM]⥴լo;[{# ~+埋Z/x*Ku }Mum:5eӕ#fE9BG[+5%Mokp+^c,?ƞSIO v{L7dSusU|7_>ft32R*.aEV`QEQEQEsy|/Fzmt&$'Tgԓbχƿz/գK[xKN,4Xo z j퉨A|i/NFrWen ?Wغ^k鶺} mgk 1*"*aFEWŠ((((((Gϋ>-Chxo:ֺ.,\0+r[8 +HMӗ2ȭ||OG/ºak"y溹ٱ$F5*[\EრJ bk[ #ٔđ@{~[[K[3->?SѼ?o&^ir%[˨iڝĖ[]D6 ccpѕ9e  }֊U+=j)/b׌|okoMvvZ]DHc:8rX=8ʊ^VK[<t}[QZwH"}aY,@.rjn_2OƱ]ͥ$|4~Ir+)߆ۃu54PM] G/ 9Εf^n-!'<{E''QE QEQEm~¾5 kIu)'*)cZuGc'GZJ^'3Ȩ}?iCT;g_* odخ@5lWFc:>xnͤ1LV"V7q5ՆO[n'7_*x{_'1 KaiYm<ݶ$$3^~ -z.YN} 'G7g*~|hGJ7ZWc0&oٛúfO|'[mFviZ+8Rr~ )r).ӯnπ?U<=?j?T''ҺW6uΓCc`ZH&]$Ag0wDrV7N\^n?U<=?j?T߃4J|=~?n?U<=?j?T߆?g%>hdES֥ES֦J|=~ ?)?G'ԑ?n:Gw`Y؜8IqKVX( ~gs5^ t(ѵk12aG$c(XcHׅP}N":jW(QEQEQEQEQEQEQEoM$oxn*9QkxIHWuc#һp_DƑơUUQZ{m -)PHdQEQEQEQEQEQEQEQEQEQEQECyuءF kKgf ALOi낾qW[?|H[M>F ˏ~-~5Bo.'h"N03" m,7 ^ZX9&NGxUSrZte1K!V\ w'3=O.5|6rzO^U7|WҼ;:qF |@ G^ QByk}>,#|=: ==Ms%x5$P/5}fl?D ]w?lO~5ׇmkV>fHbR}|m|o׼#q/ً%YxZӯo--HhGfUff{_xc}{SQ*<+uf'=zt򵢿W54/Gg__h[K}ݔHrXwjYi=(#s^W%?oO>;촫u-F1%qYpg=43_uO>tmX MnxcnZk zi+{X.}[O~ϤjR+w[_i4(22@9IѾ+xW\mm赈-#qi/IA~6+mozW[5:wOfm,:DHbPc/ OKZ?_$'"X8tK" R utWz̥gf*F8bC5|}qهLoPY瑔{8qrNih `+aEPEPEPEPEPEPEP^+d$gO .JKO`sDܕ^E\&Mnؗ8xSXŌ'J!'ĀF_V D]w Z۩+j N8 q3/`kOMVehjZ]K5ݻT="q4җ-$hQE0((((("bOjoo0;xU L'i:UUQ\gq*A $TzzWŋkT$?~ jK>,Z /ۡVbOQkTa.<2~ç0vZ&a_|_|3y|4? 5KF2>V㿏5K\4;% 9+~~Ͽ Y< 3A;vż [.߉BJ*.{/(AQ@ OuټK|:Q3"uf'rPM~a~7ǟk5_AG־olזwy veΣ*Q/*|W^_rT?>xW5@&@/Ys__ ~Gxbk41mY8&&++ĭOoxL5]f )-Dz9<  O2( ;đc ʙ^zw?g[ O٫ʿY@Q:=y?-2c3y_CxjiQ[ɓ0$Ta־. ;9A>BU5|'.|;q&Ƚ2:pq їRkw/cVW0M'*cRk#]gxR? xSvpy(EfVR+ۙ[VJ0m,֞ kbWhFTN}LU~ 4oxWмazbfB<5;X;1د,,~>|)oiotgRel3놏w< .?Z及>,>>Ek"26#6XcH1GJo/Yk /5^y-ZtVO=kUY)9umvqlx/q+C:\x_Ss>;U  85Y~(E?V=0A 8p|+J*/+%]B7ohZ-I VѬ}6)kmvXQE((((((((OxzBt5]"#͝I^+R?b]BQ7/,_NSxQrnN2 }EtR*IxWoK_!60-V~V>3GqK:WC ?e:ڌ& .1*apN+۟ǟ o^ ?&7Hljtw]h 4N^̬k~_>:_9sO+J*e%ʝe#H"B@IE0((# ZZ(, cPOx4SR2wr8a.J+땞}caOxg_vK~_qG*}z3Pan#B(|Aca_t>*?~7.墏U0:]GC>W_GCGCW.墏U7x.ه,~RKۯxXKy/ob"PĜlU2U\[ (QEQEQEQEQEQEQEQEQEQEQEQEQEQEQES54Ѵ Kt24Ve`;*X +N{&ũM\4H"$JsH`>!¬2[k +Ϳg_~4{ eTK=5dWW9kϴe{e.8tٹϿ?#57o5ΥuKh&ݞ'@=UB/>3h8.m}xM.gh|̜H# G=¿b1|e/ meMiAU-z `:zc^2JxS߄ƕ_bk H8cx$  i*0NP>ߍs4º'χ6[sJ9l fχ~OF=SFB΀JUO _|,?~ ׈d,>+xW՟WP'' r+2k__=ލO lmR4G˳Hٜ> bzPѭ/>Ƴ\RrI\=CzΑxw[]GOeYY|2X_w& OxK?is)yN9^O^.a~O s<=]:L8ic'd:)B]>gnV=?K1xQt -JDw*)v>ᯉźR,)ð > lc엦|Y7_xC is|A֯uEķpD4p,|b 1+vOZ|;t/zxoHŗ){K8bX3A?"sSpO>c'Dm7tMG6H e{lVB=3K|M.=R}Cbѻ \~+υ5Nsi.xSWtxmĵD8O5BgP4M+HKRF1$3zB4/G|9RZ6l8PH(ߴ/mg "ҵs!069<^ñj1?->o(3!!gIX?g6`Nկ5-,`*y=ʕ5k=oߖ{y>4iZintWԎhg[ @ 9--rp vھkiWoeg O3*FY |C|WO#Ŀ\_l$6C˃@,10{Bj7/ /ڇGJux4饖woBUc+?J| Zïcsw?'!-s=#Y=ٯPh:^؋y.JyQ (|a|6 gH-`,AN`Ԏ%⿆/ hZƠj'h4Fbz@-ز/QZh(K{G8*I&-N_kn5N$6fYa7]'}isFӾ%>,u=ʻuK;ˬMo Ђ{Srk`x?w^@uZ6nU!Ie`;/h ;T𦙩x-K G坕C2meR zկfٷķk> 4WXhf'D(sF?oɦ.$>d** }|Xg䬊qjA.OCOe @wNg%-LM z|QcV-[ivK-|]> YGa}s]Y=Y~vgUԁYОM{úFk~2LXҦmA`9N yGkxV;J%07F34rG~:ֿ/SWmFs<3rٝDT#;Dh)S?h |H"k׾']Kgg/I0*OCwxF/9o&{mCL32cx kG9[F'OsҎ8GZ'M-'T^h$@&aԩ皧B-վm??W>?jxzmVoOy4i&%dq&H h Y>tor4zu2<@.1"e~SN/)] !aBLL" 碴!zuϋ6_& /O@AqJ5vS}Sß n5m-׈H:Nퟺ$AǨambFb:SRÒurVx#p7Pe6׏L||2[~|H egiYM2TdB6qʜ\?Zo#y1J13_1xZ?f?A<>;O-tG‹"ʅ*CdpF*m<;5~Ζ;-#7ڧbAwn7;%zƝ8º%n96X]HYyEƕ9'.kqO]e bmqqxV[5K6;(݀9ik t {_!\jqCu79(ǹO9a=phmo5ȥed圸's1%ɯHMEc|E&C<1OKxfHR"͡P*IEzޅYoFҴE+1NFIRy'W*4O]Ŀ9V4OvQj:]⧗1txY,[%WW<;x]ӮMz{y"6:Nylݶ5iv`mY@=zNG{Xٓ@>#!,Y:(yn7`=t_~  5sY}kZ1Q֯fX[ W}E'VmrX񟄬Q4}n&>V5i2jo↓㻍[]][JVK;XK(VE7g^E?k> =Lnm[MɛՆ2qx޵QEfvAQH(٧$$IfF!vh5 5#v #v:V F065 544 FaFyt]f}DyK _Toc289673331}DyK _Toc289673331}DyK _Toc289673332}DyK _Toc289673332}DyK _Toc289673333}DyK _Toc289673333}DyK _Toc289673334}DyK _Toc289673334$$Ifl!vh555N #v#v#vN :V<l t06555N alytt$$Ifl!vh555N #v#v#vN :V<l t06555N alytt$$Ifl!vh555N #v#v#vN :V<l t06555N alytt$$Ifl!vh555N #v#v#vN :V<l t06555N alytt$$Ifl!vh555N #v#v#vN :V<l t06555N alytt$$Ifl!vh555N #v#v#vN :V<l t06555N alytt$$Ifl!vh555N #v#v#vN :V<l t06555N alytt$$Ifl!vh555N #v#v#vN :V<l t06555N alyttDd $ b  c $A?   !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~      !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~      !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~Root Entry FPɌ1Data UsWordDocumentObjectPool 1PɌ1_1105538452F11Ole CompObjfObjInfo !"$%&'()*+-./0123456789:;<=>?@ABDEFGHIJKLMOPQRSTUVWXYZ[\^_`abceg FMicrosoft Equation 3.0 DS Equation Equation.39q ´ * c a =* 2 *c K() * 2 *i F*i S()Equation Native _1106216541 F11Ole CompObj f FMicrosoft Equation 3.0 DS Equation Equation.39q` k=vpmEXTF *xDu k=v"pmObjInfo Ole10Native  dEquation Native F_1210154174F11Ole CompObjfObjInfoEquation Native ] FMicrosoft Equation 3.0 DS Equation Equation.39q Abt =" y  x FMicrosoft Equation 3.0 DS Eq_1210154168F11Ole CompObjfObjInfouation Equation.39q - E=2G(+1) FMicrosoft Equation 3.0 DS Equation Equation.39qEquation Native I_1143806899F11Ole CompObjfObjInfoEquation Native  1Table)SummaryInformation( #0jq E c =E f V f +E m V mOh+'0 ,8t     ECSS-E-HB-32-20 Part 8A4Structural materials handbook - Part 8: GlossaryECSS Executi?3"`?2+[;55zVCDJ`![;55zVC xcdd``f 2 ĜL0##0KQ* WORcgbR Vq;PT obIFHeA*Fݿ,Y0D2@penR~CPkry V8p( T>2fiը$Ƽ'<\? ; df%܆˝sNg{E{?ly 1Ab`řdKr烸/Dp̳ZZǀ Lh~J;ev dn, ~"4,XX0AݡƮL=9̫d Q?X3b7"pv0?1‡Àl8-fQP  ǧi&߶ =[=rI)$5bPd+> 1h:(G33X?http://www.dlr.de/yX;H,]ą'cDyK yK Vhttp://www.man-technologie.de/yX;H,]ą'cDyK yK Vhttp://www.man-technologie.de/yX;H,]ą'cDyK yK Bhttp://www.onera.fr/yX;H,]ą'cPDd  b  c $A? ?3"`?2\KrHE% vJ`!n\KrHE% @0= 8<xcdd``$d@9`,&FF(`TՁ]RcgbR 6x Xzjx|K2B* R>0pE1AtP!.#lL 0 L *'] ZZ |\*g`0ˈk+K3 Hgn% +_O`ˠ|f ?~P0@penR~CP)'W6v;n0:ܞ `VrAC ` v ßI)$5bPd+> 1h:(b70A"RS1XDd tb  c $A? ?3"`?2;&w/O/N~ J`!v;&w/O/N  DxuQJA};wK#8$MB'Ĥ1I/ V6)lS`ceRQ 9fyoynV8y!qhH)JĠLY]^/3ϭc #`>g1Ӛ^G_E@C -Ta4ơK:q4 [8<>#gTY~ϫ{y-?7õe m .ߚ|'="s^sR~L53ހfʸ^ PDm=E1 ܱ lYj+KYMDd Xb  c $A? ?3"`?2N#eؤ3sn J`!kN#eؤ3J  7h9xcdd``Ved``baV d,FYzP1n:B@?b u<깡jx|K2B* Rvfbv,L ! ~ Ay ;|.? _9ӺYt9Ʒ\ 0`|ߵ~gdqd!ܞ 6{P 27)?Ek͂B8 nO=m= ~L m%4Թ14=ddbR ,.Ieԡ"|b@33X?2%k[Dd b  c $A? ?3"`?2X^ ץˮ[\ J`!yX^ ץˮ[\z`Gxcdd``ed``baV d,FYzP1n:&~! KA?H1Z +깡jx|K2B* R&ʹ 01d++&1l?z+8U`T T@:s+aܨ ~92?1ȄJ7 緳簠{0@E W&0;~qr}Nw1e 2Bn&߶ K\d[{F&&\A DL,İr0as ppppppppp000H@H DNormal CJOJQJ_HaJmH sH tH @r D Heading 17$$$$ & F (H&d*$@&Pa$5CJ,KH OJQJ\^JaJ t@rt D Heading 2$$ & F X*$@&-5CJ OJQJ\]^J_HaJmH sH tH prp D Heading 3$$ & F *$@&*5CJOJQJ\^J_HaJmH sH tH XrX D Heading 4$$ & F h*$@&5OJQJ\aJlrl D Heading 5$$ & F *$@&&CJOJQJ\]_HaJmH sH tH HH D Heading 6 <@&5CJ\aJ:: D Heading 7 <@&@@ D Heading 8 <@&6]N N D Heading 9 <@&CJOJQJ^JaJDA@D DDefault Paragraph FontRi@R  Table Normal4 l4a (k(D0No List 2r2 Psymbols OJQJaJr@r DHeader+$ 9r x&dPa$m$ CJOJQJ_HaJmH sH tH NON Dgraphic$$$ha$_HaJmH sH tH LO"L #bGlossaryxOJQJ^J_HmH sH tH NOq2N BReferences:cont & F ^ R @BR DFooter($ 9r $dNa$CJtRt D NOTE:numbered#$ & F7 <]7^ a$OJQJ_HaJmH sH tH bbb ]G indentpara4 0^ `0 CJOJQJ_HaJmH sH tH TqT F5Normal Para ZchnOJQJ_HaJmH sH tH ZYZ N- Document Map-D M CJOJQJ^JaJ\\ DDRD1$$ & Fh*$#5CJOJQJ_HaJmH sH tH \\ DDRD2$$ & F*$#5CJOJQJ_HaJmH sH tH B B Drequire:indent2 / ^/ dd D NOTE:cont$7 <]7^ a$OJQJ_HaJmH sH tH Drequire:indentpara28$  i / d<<7$8$H$^/ a$^J_HmHnHsH tH ull DNOTE-$ & F  7 x]7^ a$OJQJ_HaJmH sH tH tt DNOTE:bul-$ & F  7 <]7^ a$OJQJ_HaJmH sH tH r DCaption:Annex Figure# $ & F^`a$#5CJOJQJ_HaJmH sH tH B"B DCaption!$xa$ 5\aJTO"T DTable:cellLEFT"POJQJ_HmH sH tH B!2B DTable:cellCENTER#$a$H!BH DTable:HeaderLEFT$ 5CJaJN!RN DTable:HeaderCENTER%$a$5CJ`b` DBul1%&$ & F  77x^7a$OJQJ_HmH sH tH zrz DCaption:Annex Table'$$ & Fa$#5CJOJQJ_HaJmH sH tH x x ;\Caption:Annex Equation( & Fx CJOJQJ_HaJmH sH tH ^ ^ t Ref_Heading ) & F x CJOJQJ_HaJmH sH tH Z Z B Ref_Annex * & Fx CJOJQJ_HaJmH sH tH RR C Tablesmall+$$^CJOJQJ^JaJ6U@6 D0 Hyperlink >*B*ph~r~ DAnnex14-$$$$ & F(H&d*$Pa$#5CJ,OJQJ_HaJmH sH tH TqrT DAnnex2.$$$ & FXa$5CJ OJQJaJ PqrP DAnnex3/$$ & Fa$5CJOJQJaJLqrL DAnnex40$$ & Fha$5CJOJQJHqH DAnnex51$$ & Fa$ CJOJQJ.". D reqAnnex12.2. D reqAnnex23@B@ D reqAnnex3 4$xa$CJaJ:R: mTable5CJOJQJ^JaJbbb )TableCloseText6$$ 7nCJOJQJ^JaJ`Or` D References7 & F 7xOJQJ_HaJmH sH tH B'B DComment ReferenceCJaJ<< D Comment Text9CJaJ@j@ DComment Subject:5\HH D Balloon Text;CJOJQJ^JaJj@j D Table Grid7:V<0<(q( DStyle1=L L ylegend>   ^ ` 6OJQJ^^ )Bullet 1 ?$ & FdxO*$a$CJOJQJ^JaJA *9FigureTable Title3@$$ & Fd)O*$^`a$5CJOJ QJ \^JaJQ fN TabbulletvA & Fq>T qTf^q`^J<m!<D1 / 1.1 / 1.1.1B F0l10D 1 / a / iC F@nA@DArticle / SectionD FDTRD D Block TextEx]^2Bb2 D Body TextFx<Pr< D Body Text 2 Gdx>Q> D Body Text 3HxCJaJPMaP DBody Text First Indent I`HCH DBody Text IndentJx^TNT DBody Text First Indent 2 K`RRR DBody Text Indent 2Ldx^TST DBody Text Indent 3Mx^CJaJ2?2 DClosing N^$L$ DDateO<[< DE-mail SignaturePx@x]fpTOC 1)Q Xp# 7]7^`*5CJOJQJ_HaJmHnHsH tH uh$"h DEnvelope Address!R@ &+D/^@ OJQJ^JN%2N DEnvelope ReturnSCJOJQJ^JaJFVAF DFollowedHyperlink >*B* ph0_Q0 D HTML Acronym:`b: D HTML AddressV6]0aq0 D HTML Cite6]>b> D HTML CodeCJOJ QJ ^J aJ<c< DHTML Definition6]FdF D HTML KeyboardCJOJ QJ ^J aJReR DHTML Preformatted[CJOJ QJ ^J aJ:f: D HTML Sample OJ QJ ^J JgJ DHTML TypewriterCJOJ QJ ^J aJ8h8 D HTML Variable6].(. D Line Number4/4 DList`^`828 DList 2a6^6`83"8 DList 3bQ^Q`8428 DList 4cl^l`85B8 DList 5d^`:0R: D List Bullet e & F>6b> D List Bullet 2 f & F>7r> D List Bullet 3 g & F>8> D List Bullet 4 h & F>9> D List Bullet 5 i & FBDB D List Continuejx^FEF DList Continue 2k6x^6FFF DList Continue 3lQx^QFGF DList Continue 4mlx^lFHF DList Continue 5nx^:1: D List Number o & F >:> D List Number 2 p & F >;> D List Number 3 q & F ><"> D List Number 4 r & F >=2> D List Number 5 s & F IB DMessage Headergtn$d%d&d'd-DM NOPQ^n` OJQJ^J4^R4 D Normal (Web)u>b> D Normal Indent v^4O4 D Note HeadingwDZD D Plain TextxCJOJ QJ ^J aJ0K0 D Salutationy6@6 D Signature z^*W* DStrong5\ DTable 3D effects 1m:V|j#j#j#j#j.j.j.j. |55\5B* \`J phB* `J ph66 DTable 3D effects 2:V}j.@j#j9jj 4}5\5\tt DTable 3D effects 3:V~j.@j j j#j9jj44~:B*`Jph B*`Jph5\5\brb DTable Classic 1:V0  j#j#j#jj 9B*`Jph6]5\56\]s DTable Classic 2#:V0  j% j#j0 jjj%  :5\B*`JphB* `J ph5\TtT DTable Classic 3:V0    jj0  j0  QB* ph5B*\`JphB* `J ph56B*\]`Jphu# DTable Classic 4:V0  jj0 j0 jj      !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstvwxyz{|}~ X5\B* `J ph56B*\]`JphB* `J ph5\Rv3R DTable Colorful 1:V0    j% j% jj%  <B*ph56\]56\]56\]TwCT DTable Colorful 2:V0 j% jj0  j @56\]56B*\]`Jph56\]4xS4 DTable Colorful 3:V0j;$ j0 j%  5B*\`Jphyc DTable Columns 1 :V0    j j jjjj#jj4l5\B*`Jph B*`Jph5\5\5\5\5\5\zs DTable Columns 2:Vj j jjjj% jj45\B*`Jph B*`Jph5\5B*\`Jph5\B*`Jph5\5\{ DTable Columns 3:V0j j jjj#j% j4h5\B*`Jph B*`Jph5\5\5\B*`Jph5\| DTable Columns 4:Vj j jjj% 4LB*`Jph B*`Jph5\5\B*`Jph`}` DTable Columns 5:V0    j jjj#j#4VB*`Jph B*`Jph5\5\5\56\]00 DTable Contemporary:V0j%@ j% j% 4<@B*`JphB*`Jph5B*\`Jph D Table Elegant_:V0j ;B*`Jph~ D Table Grid 1z:V0jj 6]6] D Table Grid 2:V0jjj#j ,5\5\5\5\ D Table Grid 3:V0  jjj0  5\5\> > D Table Grid 4:V0  jj0 j0  B5B*\`Jph5B*\`JphB*`Jph  D Table Grid 5:V0    jjj# j 5\5\$# $ D Table Grid 6:V0    jj#j#j (5\B*`Jph5\J3 J D Table Grid 7:V0    jjj#j# j 25\5\5\5\5\ C  D Table Grid 8:V0jjj%  H5B*\`Jph5B*\`Jph5B*\`JphvS v D Table List 1:V0  j%@ jj#j0 j4M@B*`JphB*`Jph56B* \]`J ph5\pc p D Table List 2:V0 j%@ jj#j0 j4G@B*`JphB*`Jph5B*\`Jph5\s  D Table List 3:V0  j# j# j 05B* \`J ph6B* ]`J ph D Table List 4w:V0    j0   5B*\`Jph D Table List 5:V0jj#  5\5\  D Table List 6:V0j%@ j# j#  45\5\  D Table List 7:V0  j%@ j% jjj# j0  4>@B*`Jph5\5\5\5\  D Table List 8:V0j%@ j% jjj#j0 4D@B*`Jph5\5\5\56\] DTable Professionall:V0j%  5B*\`Jpho DTable Simple 1:V0  j#j# rp r DTable Simple 2:Vj#j# j#j# j#j#O5\5\5B*\`Jph5\5\5\q DTable Simple 3l:V0    j%  5B*\`Jphp p DTable Subtle 1 :Vj0@ j# j# j0  j. jj45\5\p# p DTable Subtle 2:V0j0  j0  j# j# jj5\5\l3 l D Table Theme7:V0C D Table Web 1h:V03j B*`JphS D Table Web 2h:V03j B*`Jphc D Table Web 3h:V03j B*`JphXr X `_Equation  1$7$8$H$OJQJ^JmHsHR R `_ Equation Char CJOJQJ^JaJmHsHtH ` ` DBul2%$ & F / nnx^na$OJQJ_HmH sH tH Z Z DBul3 & F fx^OJQJ_HmH sH tH P P WITabFigx^`5CJOJQJaJvrv DDocument:Subtitle<^'5CJ,OJQJ^J_HaJmH sH tH O DDocument:Title#x&d0 P0^.5CJHKHOJQJ\^J_HaJ mH sH tH p#rp D0Table of Figures& p# 7nx]7^n`CJOJQJaJT T Drequire$<<^a$_HaJmH sH tH > > D Footnote TextCJaJ@& @ DFootnote ReferenceH*vvDpTOC 2) Sp# 7Sx]7^S`'CJOJQJ_HaJmHnHsH tH u\2 \ D list:level1$ & Fxa$OJQJ_HmH sH tH `B ` D list:level2$ & Fxa$OJQJ_HaJmH sH tH 8R 8 Drequire:bulac18b 8 Drequire:bulac28r 8 Drequire:bulac3` ` D list:level3$ & Fxa$OJQJ_HaJmH sH tH V V D list:level4 <<OJQJ_HaJmH sH tH \ \ D indentpara1$7<^7a$OJQJ_HmH sH tH \ \ D indentpara2$n<^na$OJQJ_HmH sH tH \ \ D indentpara3$<^a$OJQJ_HmH sH tH z z DTable:Footnote$$$ P^` CJOJQJ_HaJmH sH tH  D,Style DRD2 + Left: 3.5 cm First line: 0 cm & FOJQJ\aJnrn DpTOC 3) p# 7x]7^` CJOJQJ_HaJmH sH tH b b DBul4' & F   x^ `OJQJ_HmH sH tH zOz DDocument Number$d!xa$/5B*CJOJQJ\_HaJmH phsH tHp! p DDocument Number Char/5B*CJOJQJ\_HaJmH phsH tHff DpTOC 4%  $  ]^ `OJQJ_HaJmH sH tH \OB \ D Document Date$a$ CJOJQJ_HaJmH sH tH ^^ DpTOC 5 f$f^f`OJQJ_HaJmH sH tH P!b P D Table:Note nS<^S`CJ\\ vpTOC 6Ldd^L$CJOJ PJQJ ^JaJmH sH tH \\ vpTOC 7(dd^($CJOJ PJQJ ^JaJmH sH tH \\ vpTOC 8dd^$CJOJ PJQJ ^JaJmH sH tH \\ vpTOC 9dd^$CJOJ PJQJ ^JaJmH sH tH b b F5 Normal Para-$$ n n#dxO*$a$CJZ Z vLarge Table TextdO*$CJOJQJaJX X vNormal Para Char CJOJQJ_HaJmH sH tH T T t Char Char4&5CJOJQJ\_HaJmH sH tH T T vBulleteH^e`CJOJQJ^JaJtH V V Q'Note#$  9dOa$5OJQJtH \ \ Q' Note Text#$  9dOa$ OJQJtH D" D Q' Table TextOJQJmH sH tH @ 2 @ Q'Equation number$a$RB R vBullet 2$ & FdO*$a$ OJQJtH TQ T Q'Note Text Char CJOJQJ_HaJmH sH tH ^a ^ Q'Note Text Char Char CJOJQJ_HaJmH sH tH lOr l #bGlossary entry$d((*$^CJOJQJ^JaJtH O! c>DStyle Heading 2 + Before: 18 pt After: 6 pt Bottom: (Single sol...<$$ & F D%dhx*$-DM a$OJ QJ ]^JaJ tH H H v Reference$ ^ `a$N N vReport$5$7$8$9DH$a$OJQJaJtHB B vTabelleOJQJaJmH sH tHP P vText$d<a$OJQJaJmHsHtHN N vequation$ &^a$5b b vDefault 7$8$H$-B*CJOJQJ^J _HaJmHphsHtHV Vv0 berarbeitung CJOJQJ_HaJmH sH tH NN Gv Char Char2 CJOJQJ_HaJmH sH tH NN Hv Char Char1 CJOJQJ_HaJmH sH tH L!L Jv Char Char CJOJQJ_HaJmH sH tH N1N v Char Char3 CJOJQJ_HaJmH sH tH <B< v  Listenabsatz ^VRVv Document InfoOJQJmHnHsHtHuBB vFigure$$xa$ OJQJtHXOrX D paragraph$x*$a$OJQJ_HaJmH sH tH PP Dparagraph CharOJQJ_HaJmH sH tH : : vIndex 1^`hJ@h DSubtitle<@&^'5CJ,OJQJ^J_HaJmH sH tH lOl DECSSsecretariat$(a$m$#5CJOJQJ_HaJmH sH tH \O\ D Published# @v7$8$H$^`v CJ^JaJ4O4 DContents 7xqx szj*Style paragraph + Century Schoolbook 12 pt ^vv szj/Style paragraph + Century Schoolbook 12 pt Charl l \4#Style Normal Para + Times New Roman B*phhrh \4(Style Normal Para + Times New Roman CharXa"X DStyle Bul1 + Times New Roman@B1B &szj Bul1 CharOJQJ_HmH sH tH ^2A^ D!Style Bul1 + Times New Roman Char@(R( szjStyle28a8H" Current List1 Fx>x DTitle&x&d0@&P3f0^.5CJHKHOJQJ\^J_HaJ mH sH tH ~Or~ D Heading 0-$$$$(H&d*$Pa$#5CJ(OJQJ_HaJmH sH tH lrl DEXPECTED OUTPUT$ & Fxa$6OJQJ_HaJmH sH tH .). D Page Number DEXPECTED OUTPUT:CONT:$$ d<<7$8$H$^`a$6CJ]^JaJtH BrB D CaptionTable$$h.X. DEmphasis6]r D Definition1($ & F S^`*5CJOJQJ\^J_HaJmH sH tH drd D Definition2$ & Fx#5CJOJQJ_HaJmH sH tH HH D TOC 4 CharOJQJ_HaJmH sH tH \\ DDefinition2 Char#5CJOJQJ_HaJmH sH tH X!X DHeading 0 Char#5CJ(OJQJ_HaJmH sH tH Z2Z DNOTE:TABLE-CELL! & F Sq<<]qVV DDRD3$$ & F CJOJQJ_HaJmH sH tH rRr -+8+Style Style Normal Para + Times New Roman +xax -+80Style Style Normal Para + Times New Roman + CharDqD |k graphic Char_HaJmH sH tH RR !+\ Caption Char"5CJOJQJ\_HmH sH tH :: +\CaptionTable Char 4 glossbullet  & FV1$5$7$8$9D>TH$Tf^`VCJOJQJaJ_`abcdq    _`abcdg    00cdmbmg+00000000@00000@0L@0L @0L @0L 00@0@0@00cdmbmg +nB/=  B P Q X 7 G H O 8 H I P        0 I N V akz>JT_ pt:Q"&>D+4GP La w}WZw}EI_ma  !!!,!1!i!n!!!!!!!!!#")"A"K""""###$$T%X%j%q%%%%%&&y&&t''((())*"****++,,--....k/~//0x00001 1R1`111"2'2W2[2w2233'3+3j3t3334444<5A5g5k555556#6O6l6667 7>7C7i7n777 8)888+909i9p9999 ::c;h;v;;;;<<<=====">.>>>>u?|???5A?AAABBBBFCNClD|DDE2F6FFFFGkIIIJJJJ3KCKKKwLLMMuM|MN#NNNOOSPYPPPmQsQQQ RRDRIRRRRR(S6SSSTTTUUU0V8VVVVWWWXXYYYY7Z@ZZZT[W[[[[[\[]c]]]H^O^^^^ ________B`J`EaKabbbbacfcccccdd1e7eoeweggggYhfhjjYk^kkkklllmmMmRmmmVnfnnnoop.pDq7rBrrrOsSstsxsssssss tt/t3tJtOtktotttEueuuuuuuuvvvvvvw8wwwyyzz{{-{{{| |}<}}}=Bhl#&ei Ԃ܂уjŅUcƊT^͌'4Ž؎&֐wYg/;”:Sŕ'#)ۘyəәX5>#*&-bg28v}INioDVץpΦDɧקP`X©۩P`~׮=GѰݰ/9Ա|ͲӲ%,>Dsw9=cp #(_j# jv'4&ɾ;pu?F&525:o7HC\k{nv-.3"ZaCK u CK.<uZf.IM-UXoYc3E=SW ~jw w!qW[#'?Dcg#Efy}<HLPq|=@[%)KOAEch5juZ^ty RV  ( 8 B S K u     ] w <WRZlp+/NmqHMAEvz&/.1MQfj  !!!!!!""O"T"~""""""`#m#######$!$/$3$$$%%%%%%&&&;'B'p'3())}***++,B,N,,,G-Y---t//h0}01.122i2v22}33334'45O5\555]6s667l77778_8e888/939J9O9k9q9999999995:9:c:t:::";(;I;N;;;;;;;< =#=J>Y>?&????@5BPBC#CCDDME\EEEELGjGGGDH]HIISJ\JJK1KKK^KsKKKL)L}LL N/NeNsNNNO&OPPyQQ RRRRRR8TATU$UzUUUUVVW)WWWNX`X.YAYYBZZZ/[<[[[[[[[\\\\]#]]]]]A^G^v^z^^^^^_A_K____f`````-a@abbbb/b9bxbbbccc-d@dhhhiDiIifijiiiiiiijj j$j@jRjjkkk2lAlll/m2mBmFmfmimnm~mmnnnnoo9oFooooo pppprqqqWrprs s&s0smssss}ttvu{uuuuv v(v.vuvvwwwwxxGyiyyyzzzz~zzzzzzz {{||l}y}~~~~.:ʁԁL&0EJgk~˃y[` )0fu>C8Xو(ʋӋJQt!+:H&3|MSsy03\`w|OR!8?<.;MNgʛĜϜ ,TaNQdh-1<Asw37ĠȠ1"0oz"*I]ݤ{1>ܧ IPRi!6 2 +68J&@VhHT׺3Bܼ"EZq;EYo /2<Abj}IO04Rty  :OPa>ACJNY]owKP *6L # HU{->J#GKchtjpu -?h"3Wd ,;k#'5<hl.8GKae [_:D$1B-DHPj-QM_|4uz/=kp #49$.Zn    C U       !"XeI[296:Xg*8($3 lxu37ae&*HL TX+    !!%!:!N!"-""#$$k%% &&{&&''''v))))+!+++++++O,,,,I-R---..K.O.f.j.{.~.........//J///01O1R111116292>2d2i222'3,3Z3f3333344C4G4w4{444445585<5j5y556$73777888899::[:`:::; ;;;G<K<f<z<>#>=>D>g>|>%?5?b@@@ ApAACD"DEFkGwGGG+H=HHHHHSI`III KKuKK@LDLaLeLLLLLM!M(M\MbMMMMMNN4N:NqNzNNNNNlOwO)PaPQQQQQQR RIRMRuRzRRRRRSSTTU-UVWW XX8X?XXX;YFYYYZZXZ\ZuZyZZZZZZZZ[[[N\\\]!]^(^h^^^^__`````````aaaaaaabbbbc#c{cccc{dd?fKfffoggZhbhEiJi{i~iiiiiiiVj\jjjjjkkkkk lIl\llllllm)m-mgmlmmmmmmmnnnnnnoo$p)pPpTptppqqrr#s,s9s=sssGtMt~ttuuuuTvcvvvw wwwxxyy9z=zMzQzzz'{1{f{m{{{|||||||}}2}}~J~f~~~eQ_:DŁjt!)p*KJ[ӈFOڊ ̌w+:ԏltÒR]v~BGhvŕԕ"z˖&ؙ :țUk[bEXw|I[ ؤܤ%(ťɥos %);F9=OSeiHXɩ),/AEady~«ثܫgҭC2JQi)ñͱkoGO۳ <@UYrc}N`"ܹ (`Ҽ]j(C/S,[k5H grPaQ "7<_cwKOW[tx(0L_07 QUuy+56[i.71n15HMpz0<-2S\EI_d l:>ox#SQHU (bj  \g9C%F#*tyZ^ns"FM)?eq"v{_g'PSei  B U b f        '     ~  m{>g&<LUk Sf |*4L\15PTjo# 5 v  #!)!a!!!!""y##;$J$$$U%Y%q%%&!&A'E'_'o'''((G)~))))))***#+,,,-o--l..5/Q///b0011223344C5J56677889999u::=;U;<6<<<I=M=|===> >>>???{@@4AOAGBWBBBpCtCCCCCCCD DQDDDDDDDEE\EoEFFGGGGGHHCIHIIIJJJJCKHKL=LILLLLLLLLMM+MMMNN;NBNNN O(OOOOOQQJQQQRRkSvSSSTT/U;UUUVVlW{WWWX XgXoXXXYYYYYY_Z}Zk[[H\X\ ]]D]Z]]^^g_u_*`8```*a7a@bpb~bbctccc.d?dvddeeff%i,iAiTiii!j6jjj=k_kkkkkkk lllllmmm,m:mno'o-oooooppp$p>pBpvp~pppKqqqHrLr*s0ssstttt%u2uuuuuavqv~wwsxxxxYy]yty{yyyyyyyezrzt{y{{{{{&|,|]|i|||%})}q}t}w}}}}}}}}~:~N~h~v~~~3S8_€‚݃3Y]ބADWZnˆІ&,cpƈ;Չى9=X`Ŋ&3ӌCUґ1Cؓ”<?%ؖ͗ڗ(ؚ]m?Gfj}ٝ.3q{ڠ/4PUukq)-kp*/lwթ۩M[ *.@DjxTa,4-C]apt:?LPmykz,OVkwuyAMg˺ /f q!"$%'(*+o+,-./012345FPr0000000000000000"0"0 "0 0 000Q0Q0Q0Q000000"0 "0 "0 0 "0 "0 "0 0 "0 "0 "0 0 "0 "0 "0 0 "0 "0 "0 0 "0 "0 "0 0 "0 "0 "0 0 "0 "0 "0 0 0 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0 0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0_0 0202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020202020 000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0&0 0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0fm0 00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 000000000000000 0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0>0 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 0620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620620 0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0L0 0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0`0 0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0)0 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G      !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrtuvwxyz{|}~0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0G0 0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0q}0 0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0W0 0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0}0 0000000000000000000000 0000000000000 0000000000 0 70000 7000 7000 7000 70 70 70 70 70 70 0@000;@000;@000;@000;@0@0@0@0@0@0@0@000;00000000000000000000cdmbmg +n= B P Q X 7 G H O 8 H I P        0 I N V akz>JT_ pt:Q"&>D+4GP La w}WZw}EI_ma  !!!,!1!i!n!!!!!!!!!#")"A"K""""###$$T%X%j%q%%%%%&&y&&t''((())*"****++,,--....k/~//0x00001 1R1`111"2'2W2[2w2233'3+3j3t3334444<5A5g5k555556#6O6l6667 7>7C7i7n777 8)888+909i9p9999 ::c;h;v;;;;<<<=====">.>>>>u?|???5A?AAABBBBFCNClD|DDE2F6FFFFGkIIIJJJJ3KCKKKwLLMMuM|MN#NNNOOSPYPPPmQsQQQ RRDRIRRRRR(S6SSSTTTUUU0V8VVVVWWWXXYYYY7Z@ZZZT[W[[[[[\[]c]]]H^O^^^^ ________B`J`EaKabbbbacfcccccdd1e7eoeweggggYhfhjjYk^kkkklllmmMmRmmmVnfnnnoop.pDq7rBrrrOsSstsxsssssss tt/t3tJtOtktotttEueuuuuuuuvvvvvvw8wwwyyzz{{-{{{| |}<}}}=Bhl#&ei Ԃ܂уjŅUcƊT^͌'4Ž؎&֐wYg/;”:Sŕ'#)ۘyəәX5>#*&-bg28v}INioDVץpΦDɧקP`X©۩P`~׮=GѰݰ/9Ա|ͲӲ%,>Dsw9=cp #(_j# jv'4&ɾ;pu?F&525:o7HC\k{nv-.3"ZaCK u CK.<uZf.IM-UXoYc3E=SW ~jw w!qW[#'?Dcg#Efy}<HLPq|=@[%)KOAEch5juZ^ty RV  ( 8 B S K u     ] w <WRZlp+/NmqHMAEvz&/.1MQfj  !!!!!!""O"T"~""""""`#m#######$!$/$3$$$%%%%%%&&&;'B'p'3())}***++,B,N,,,G-Y---t//h0}01.122i2v22}33334'45O5\555]6s667l77778_8e888/939J9O9k9q9999999995:9:c:t:::";(;I;N;;;;;;;< =#=J>Y>?&????@5BPBC#CCDDME\EEEELGjGGGDH]HIISJ\JJK1KKK^KsKKKL)L}LL N/NeNsNNNO&OPPyQQ RRRRRR8TATU$UzUUUUVVW)WWWNX`X.YAYYBZZZ/[<[[[[[[[\\\\]#]]]]]A^G^v^z^^^^^_A_K____f`````-a@abbbb/b9bxbbbccc-d@dhhhiDiIifijiiiiiiijj j$j@jRjjkkk2lAlll/m2mBmFmfmimnm~mmnnnnoo9oFooooo pppprqqqWrprs s&s0smssss}ttvu{uuuuv v(v.vuvvwwwwxxGyiyyyzzzz~zzzzzzz {{||l}y}~~~~.:ʁԁL&0EJgk~˃y[` )0fu>C8Xو(ʋӋJQt!+:H&3|MSsy03\`w|OR!8?<.;MNgʛĜϜ ,TaNQdh-1<Asw37ĠȠ1"0oz"*I]ݤ{1>ܧ IPRi!6 2 +68J&@VhHT׺3Bܼ"EZq;EYo /2<Abj}IO04Rty  :OPa>ACJNY]owKP *6L # HU{->J#GKchtjpu -?h"3Wd ,;k#'5<hl.8GKae [_:D$1B-DHPj-QM_|4uz/=kp #49$.Zn    C U       !"XeI[296:Xg*8($3 lxu37ae&*HL TX+    !!%!:!N!"-""#$$k%% &&{&&''''v))))+!+++++++O,,,,I-R---..K.O.f.j.{.~.........//J///01O1R111116292>2d2i222'3,3Z3f3333344C4G4w4{444445585<5j5y556$73777888899::[:`:::; ;;;G<K<f<z<>#>=>D>g>|>%?5?b@@@ ApAACD"DEFkGwGGG+H=HHHHHSI`III KKuKK@LDLaLeLLLLLM!M(M\MbMMMMMNN4N:NqNzNNNNNlOwO)PaPQQQQQQR RIRMRuRzRRRRRSSTTU-UVWW XX8X?XXX;YFYYYZZXZ\ZuZyZZZZZZZZ[[[N\\\]!]^(^h^^^^__`````````aaaaaaabbbbc#c{cccc{dd?fKfffoggZhbhEiJi{i~iiiiiiiVj\jjjjjkkkkk lIl\llllllm)m-mgmlmmmmmmmnnnnnnoo$p)pPpTptppqqrr#s,s9s=sssGtMt~ttuuuuTvcvvvw wwwxxyy9z=zMzQzzz'{1{f{m{{{|||||||}}2}}~J~f~~~eQ_:DŁjt!)p*KJ[ӈFOڊ ̌w+:ԏltÒR]v~BGhvŕԕ"z˖&ؙ :țUk[bEXw|I[ ؤܤ%(ťɥos %);F9=OSeiHXɩ),/AEady~«ثܫgҭC2JQi)ñͱkoGO۳ <@UYrc}N`"ܹ (`Ҽ]j(C/S,[k5H grPaQ "7<_cwKOW[tx(0L_07 QUuy+56[i.71n15HMpz0<-2S\EI_d l:>ox#SQHU (bj  \g9C%F#*tyZ^ns"FM)?eq"v{_g'PSei  B U b f        '     ~  m{>g&<LUk Sf |*4L\15PTjo# 5 v  #!)!a!!!!""y##;$J$$$U%Y%q%%&!&A'E'_'o'''((G)~))))))***#+,,,-o--l..5/Q///b0011223344C5J56677889999u::=;U;<6<<<I=M=|===> >>>???{@@4AOAGBWBBBpCtCCCCCCCD DQDDDDDDDEE\EoEFFGGGGGHHCIHIIIJJJJCKHKL=LILLLLLLLLMM+MMMNN;NBNNN O(OOOOOQQJQQQRRkSvSSSTT/U;UUUVVlW{WWWX XgXoXXXYYYYYY_Z}Zk[[H\X\ ]]D]Z]]^^g_u_*`8```*a7a@bpb~bbctccc.d?dvddeeff%i,iAiTiii!j6jjj=k_kkkkkkk lllllmmm,m:mno'o-oooooppp$p>pBpvp~pppKqqqHrLr*s0ssstttt%u2uuuuuavqv~wwsxxxxYy]yty{yyyyyyyezrzt{y{{{{{&|,|]|i|||%})}q}t}w}}}}}}}}~:~N~h~v~~~3S8_€‚݃3Y]ބADWZnˆІ&,cpƈ;Չى9=X`Ŋ&3ӌCUґ1Cؓ”<?%ؖ͗ڗ(ؚ]m?Gfj}ٝ.3q{ڠ/4PUukq)-kp*/lwթ۩M[ *.@DjxTa,4-C]apt:?LPmykz,OVkwuyAMg˺ /f q!$'*o+,-./012345FPr000000000000000@0L00j@0L @0L @0L 000@0@0I@0I@0I00000000 000000A0 000000@1 000000@0 000000@00 0 070 070 07@0 0 070 070 07@0 00 00 00 @ƴ 0  @ 0 @ 0@0#@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0-@0#@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@09@0#@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0Z@0#@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0P@0#@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@02@0#@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0"@0#@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0h@0#@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0{@0#@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0#@0'@0'@0'@0'@0'@0'@0'@0'@0'@0'@0'@0'@0'@0'@0#@0_@0_@0_@0_@0_@0_@0_@0_@0_@0_@0_@0_@0_@0_@0_@0_@0_@0_@0#@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0#@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0#@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0X-@0#@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0H@0#@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0[@0#@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0L@0#@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0#@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0#@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0B@0#@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0x@0#@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0#@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0#@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0@0#@0ۯ@0ۯ@0ۯ@0ۯ@0ۯ@0ۯ@0ۯ@0ۯ@0ۯ@0ۯ@0ۯ@0ۯ@0#@0@0@0@0@0@0@0@0@0@0 - 0 )0000 )000 )000 )000 )0 )0 )0 )0 )0 )0 @0@0@0@0@0@0@0@0@0@0@0 000000000000      !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnoprstuvwxyz{|}~000000T '+$F؍( y+! 7DP[cqGH&}#)y.x8?CjJ}U^:flKw S}Dfv\^2 8'f,019BFOXLbinv{|ǔÛXf+wohu6 !)/l:W>BHMT[`[hem}rzs~g*2Ѹ{$(x -]$:+/L7hALS\Z]_gp=zA'b4x!     !"#$%&'()*+,-./012345689:;<=>?@ABCEFGHIJKLMNOQRSTUVWXYZ\]^_`abdefghijklmnoprstuvwxyz{|} 0a+Tln!=?@Bbp (,-/[}!8(uRSSSlllN~b~d~i}F]gggggggg?hVh_hvhUU X%X%X%ĕX%̕:XX9 XXX:::9 :9 9 9 9 9 9 5MP{ UUUU&  x T&b$,@:Q|)y ;b$2K@f2$K ژ 5b$WײəC$5Txb$2q/kp9XE\b$u#x^j<-b$sڲ$yqsb$\# Qg4'izf5b$?1ꕔ+zN0b$]iD3e'=62$?fW+)w472$.`kEk~6m@,,O2 b$hYёR$cƞƣ b$$CB@{b$F\w_Cmz b$QRsT; ? b$I^c|('Fb$bş b$4YZd b$>B]Qt~ 2$~yqm&>2$zK y :W2$_;4O#هIb$7K-LQ<ęT+o b$$z,!ȗ'Jb$cQ_kw 2$}s\dD0t2$?8w"c4FRbb$MA)0 R$jNWU [#; R$(j6e{G8?R$1Qh^k9BZ]CR$ m>˳G,#r\J R$j2s b9˰bQ R$fQ-L??Ё3R$D6Gj` R$ʡfоÉ.a R$;]F R$߰t<ƍ0R$"x-oU6^R$Ԩ,@.Z R$S#VA[Y R$\9B/wHùR$.*Be4n1`HYR$=X w'`ʷV R$ orw0˗`2R$KgȀ2>5R$`"~P*ܷ R$U &Ead<'n R$tPE7PɪC R$_J<ęAkE R$QǭܶO{%jOc R$F妳@Y^3; R$dJR& R$|>U9`m=V R$ #֕MKգ R$okA"醒WWR R$WX_0\9l|R$ s[$2R?"h]HR$Atm EҳER$CN9xᵞFĩBfb$ݎ5#Pj >b$/T3 b$eH}J*殶?xE b$g| _" 3 b$PY-V%̺ - b$bpl29#.3t.ub$߻]Eh+b$/jbX};H1 b$3OcYKѕw b${FF$;i 7&~ b$0LPS M8'b$#}Fsb$P"F"E b$ s1@N&4Ռn b$ J agC X b$UX2 =3 b$Va B1{l b$:(X, 1% b$%i5q yb$ k _-ɤEH b$.hQ̼}N b$^~RJ5jgZ b$FX<.(4 b$O:&hPBBk6SAb$!Y>%NbgĖ' b$HrQ)] 'B< b$Ŋj}N N8b$Ȝg7y0X|mb$K'sT‘[rb$]_v k b$i-|J6cl*R$WX,ygSX3c,b$Q2Vج=0njޫKqR$ewً *, 0*R$c!Y~8Ž'$0 R$w #As(R$8L: KE-E'R$exp?AnyR$#qD'`f*0,s2R$Gd[!,e}R$tҼDT~c@ b${ڮ)ԋA8"}b$b6pvTb@t\qMVC R$>PޫKcf80K R$=ۖoF1_q*, R$f^Z[jLE4,V b$M+i$ #&lz b$`ȭuDF 4>c-q b$dw9zff&SNR b$z[|oBdz< b$Ԣ:FgUфH -qpb$J1U˴Ԙ6s b$>Gn"(l>r߃b$55q`tR>CR$ ŭv < &b$ w\ &ƉxR2$}ɰM<mR$>9@1r5hm4b$QzTGuolzBR$feNrn* R$Je0CPA2 Q R$1h= l(aʩ R$)3ѹs5#*Pb$)L҃Y9R$IJmZbR$gV_8Gps R$߉s%2'Kds R$[R76Өs) R$chVCGPpR$ǐRyB4i?E R${6hP<' iR$gq֠q^U,0R$㱣huN^֞:zR$^ۏzKϹ:<R$ɔ+3r&NR$'J+rGy2k:Hy1 R$ٴ.&LZT_% b$3thƠ,"dR$Vf֧$,s`~K2$~*4usNX?ub$蟽c}pxʣ(R$<<еmaٷPb$\1G+KSo PX|R$,L ?=|b$$2Q[5|ռ$mR$z+VLF鑘ktb$Əs "UH{{ ^R$.kĥ^" b$XKge0RDDMR$7lO;'hJN R$ %΄(aAIV4 R$KAdb$WKOO{!"m\b$́z?#|kalȓb$nfae:+զ R$Nm[h?:y R$xCX L ~ R$=.,$ R$бCWSa7`. 2$$-O,˶ ƆEb$bp*v1U 2$I"b$m[śdupNԵb$ c`(GIb$g4gʍ_a]2$fdsD-"Rӊ!2$i)69 wPb$|!iĤpb$/LAv$+uiN2$ IǻKG4)sb$5qL6e["4b$ocK*$D&fI8< b$S4}qR_2$Tg o#9c 2$w؉:U{Hf2$k9y\CN(}r- b$WɆX[S)2$OWirAթK i2$J$iBB552$Z2VenȽC2$^"ӊr!ߠD2$5AeNks0i[ 5q۴b$84;u=$6V2$$]Jѱg=m2$oHqb$MTOɨ]-AAb$h&7 ;['2$\hI0T p:">+G LwWwE_ !,!i!!!!!#"A"""#$T%j%%%&y&t'()**+,-..k//x01R11"2W2w23'3j3344<5g5556O667>7i77 88+9i99 :c;v;;<<==">>>u??5AABFClDD2FFIJJ3KKwLMuMNNOSPPmQQ RDRRR(SSTTU0VVVWXYY7ZZT[[[[]]H^^^__B`Eabbacccd1eoeggYhjYkkklmMmmVnnop7rrOstssss t/tJtkttEuuuuvvvwwyz{{|}}=h#e ԂуjŅUT'ŽY/:#ۘyə5#&b2}IiDץɧP©P~=Ѱ/Ա|Ͳ%>s9c #_ j'ɾp?&25o7Ck.ZCuC.uZI-XY3=~jw wqW#?cEy<Lq=%KAcjZt R ( B K   ] <Rl+mHAv&.Mf !!!"O"~"""`####$/$$%%%&&;'*+B,,G-t/h012i2}334O55]6677_88/9J9k999995:c::";I;;;; =J>???5BCDMEELGGDHISJL}L NeNNOPyQ RRR8TUzUWWNX.YZ/[[[[\\]]]A^v^^^A__``-abb/bxbbc-dhhDifiiiij j@jjk2ll/mBmfmim~mnno9ooo ppqWrs&smss}tvuuv(vuvwwxGyyzzzzzz {|l}~~.ʁ&Eg~y[ )f>8ʋJt!:&|Ms0\wO8;NʛĜ TNd-<s3Ġ"o"Iݤ{1ܧ IR!  8&VH׺3"Z;Y/<b}I0t P>AJYoK 6HGctju ?Wk#5h.Ga [:1DP-M|u/k 4$Z  C    XI26X*$lu3a&H T  !!:!""$k% &{&''v))++++,I--.K.f.....//0O1116292d22'3Z3334C4w444585j55$77889:[::;;G<f<>=>g>%?b@@pACkGG+HHSII KuK@LaLLLL!M\MMMN4NqNNNlOQQQRIRuRRRSTUW X8XX;YYZXZuZZZZZ\]^^_`````aaabbcc{d?ffogZhEi{iiiiVjjjkkkIl)mgmmmmnnno$pPptpqr#s9ssGt~tuuTvvwwxy9zMzz'{f{{||||}}Q:j!p*JӈFڊ w+lRvBhŕz U[Ew|I ؤ%ťo%;9OeHɩ),AayثҭJiñkG۳<UrcNܹ(Ҽ]([5grP 7_wKWt(L0 Qu+[.1Hp0-SE_ l:oH b \9%#tZnF)ev_Pe B b       ~ m{><US|*L1Pj# v #!a!!"y#;$$U%q%&A'_''(~)))**,,o-5//b01234C567899u:=;<<I=|=>>?{@4AGBBpCCCCDDDDE\EFGGGHCIIJJCK=LLLLLMMN;NN OOOQQRkSST/UUVlWWXgXXYYY_Zk[H\ ]D]g_*``*apbbtc.dvdef%iAii!jj=kkkk lllm,mn'oopp>pvppqHr*sstt%uuuav~wsxxYytyyyyezt{{{&|]||%}q}t}}}}}:~h~~38݃YބAWZˆ&cƈՉ9X&ӌC1ؓ”<ؚ͗]?f}.qڠ/Puk)k*lթM*@jT,-]p:LmkOku@   !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~      !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~      !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~      !"#$%&'()*+,-./01234567 89:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~      !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~      !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~      !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~l******<<       I V kJ_tQ&D4Pa }Z}Im !!1!n!!!!!)"K""##$X%q%%%&&'()"**+,-..~/00 1`11'2[223+3t3344A5k555#6l66 7C7n77)8809p99:h;;;<===.>>>|???AABNC|DE6FFIJJCKKLM|M#NNOYPPsQQRIRRR6SSTUU8VVWWXYY@ZZW[[[c]]O^^ ___J`Kabbfcccd7eweggfhj^kkllmRmmfnno.pBrrSsxsssst3tOtotteuuuuvvv8wwy{-{{ |<}}Bl&i܂cƊ^͌4؎&֐g;”Sŕ')ә>*-g8NoVק`۩`Gݰ9Ӳ,Dw=p (jv4&;uF53:H\{-3aK K<f.MUocES !['Dg#f}HP|@)OEh5u^yV 8 S u   w WZp/qMEz/1Qj !!!"T""""m####!$3$$%%%&&B'*+N,,Y-/}0.12v233'4\55s6778e8839O9q999999:t::(;N;;;;#=Y>&??@PB#CD\EEjGG]HI\J)LL/NsNN&OPQRRRAT$UU)WW`XAYZ<[[[[\\#]]]G^z^^^K__``@abb9bbcc@dhiIijiiiij$jRjkkAll2mFmgmnmmnnoFoooppqpr s0ssst{uu v.vvwwxiyyz~zzzz{|y}~~:ԁ0Jk˃`0uCXو(ӋQ+H3Sy3`|R!?MgϜ,aQh1Aw7Ƞ0z*]>Pi62+6J@hTBEqEo 2AjO4y a?CN]wP*L # U#Khp-h"3d,;'<l8Ke_D$B-HjQ_4z=p#9.n  U    !"e[9:g83 x7e*LX+  %!N!-"#$%&&''))!++++,R--.O.j.....//1R11172>2i22,3f3334G4{4445<5y56377889:`:: ;;K<z<#>D>|>5?@ AADwGG=HH`IIKKDLeLLLM(MbMMMN:NzNNNwOQQQ RMRzRRRST-UWX?XXFYYZ\ZyZZZZ[\!](^^_`````aaabb#ccdKffgbhJi~iiii\jjjkk l\l-mlmmmmnnno)pTppqr,s=ssMttuucvv wwxy=zQzz1{m{{|||}2}~_DŁt)K[Ǒ:ԏt]~Gvԕ"kbX[ܤ(ɥs )F=SiX*/Ed~«ܫQ)ͱoO @Y}`" `jC,kH a"<cO[x0_7Uy5i75Mz<2\Id>x#U(j gCF*y^s"M?q"{g'Si U f    '    g&Lk f 4\5To5  )!!!"#J$$Y%%!&E'o''()))*#+,--Q//01234J567899:U;6<<M== >>?@OAWBBtCCCC DDDDEoEFGGGHHIIJJHKILLLLM+MMNBNN(OOOQQRvSST;UUV{WW XoXXYYY}Z[X\]Z]u_8``7a~bcc?ddef,iTii6jj_kkkkllmm:mo-oop$pBp~ppqLr0sstt2uuuqvwxx]y{yyyyrzy{{{,|i||)}r}w}}}}~N~v~~S_€‚3]DXnІ,p;ى=`Ŋ3UґC?%ڗ(mGj~3{4Uq-p/w۩[ .Dxa4Cat?Pyz,Vwy |o+  ?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~/ / ?DDC!S!c!h!h!99BBBUU[[^^$w+w1w1w1șș|DDiiE"N"N" ####*#O#O###1'1'ouu(,,XXsxxNbgg##33T4v4v4.:;:O:O:kk**6)==DDXXooyyyy}}}}\\66   !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~9*urn:schemas-microsoft-com:office:smarttagsplaceB*urn:schemas-microsoft-com:office:smarttagscountry-region8*urn:schemas-microsoft-com:office:smarttagsCity=*urn:schemas-microsoft-com:office:smarttags PlaceType=*urn:schemas-microsoft-com:office:smarttags PlaceName9.*urn:schemas-microsoft-com:office:smarttagsState ....bdlmq+mn       ! ( ) , - 7 8 ? @ B C D zhuw  %23;<HWYwT%W%&&f&j&l&p&t&x&h's'(((())v++./3333334455[5f555#6)6<<==>?I???@@@@BBBBCCDD2FFGGFIMIMMNNOO|PPR!RRRS'ScTlTiUsUVV ]]^^__``a abb7e=e>eDegg|hhhhjkEkLkkkkkkkkkkkkkl%lll%m4mRm`mammmppqqssotutvt~tvvRy[y(z0z{{ozȂӂ.7)0Å %'.s{;E RTתy hr7>2=տ޿(.  7Cjqq}5?mwFMDFPW<K~fp^iW[~cfu|fr~7> !    v{/7lo5=AIo"}"$#*#B#J#e#l###$ $ **99.;9;lAvA)B4BFG GGdGhGOKUK,M3MNNV*V/V8Vaabb c,chhiiiinnnnnno$o%o1o2o8o\tftww6y9yeygyFQ>BJV*1PWVYgmLZu{(/ &Ǘ˜ܘ#zȠՠġС#^a&2z%+@CKNq~]hfsds^g CL>YHLms),Wb */lq(47?F( 3<9BCL*13<#   ((~....1111G2P2d2h23344444455<5J5777788%9/9999:[:_:::;<<< <!<G>M>_>e>? @BCrE{EEEFF1G:GH#HEJRJnLwLMM,S4S;SESFSSSZZ[[\\]]``a aaa6bFbb c cccctdxddd?gLgJi[ijjjkkk-m=mmmMnUnpp.q6qIqRqSq[qrrrrrr_shst&t||||||}}X_ÂV`EI.5)BFGJӡޡQ\ޢ)*5ɥ5DI $'EVsy&-EH:C"z68RTNUV`JU 18V]09Z]nr#&:=  F Q   @!K!&&'(.(^.j.g1t11>@>@%@yAAE E$E+E3E9E=ECEI IYK`KqLvLLLOOOOWXYYYYYYZZ%[)[>^J^^_F_Q_ngughhhhiiBjHjkkkkkkkkkkllllmm_nkn oooopppp#t,ttttyyyyy/{:{y{{{{{||%|́ EH-0<>™$ GM&0pxz&@GPW(0ux !!""$%'(*mo)./bc+mn G I FGnQl4?}WY$$&&V))"*(***++~//2223334Q444 5578)8888@<C<2F5F6FFQ RRRS&TTTUUWWX[[[4\__weee f!h)h^kknnu vxxyyuƊƤV%,k -uv˻monF.23KXn&<q}fDFMjDFc`i~WZ~cfPW;Hmn1S  */MNl<>TV)+  U!""$ $%5&6&&***q++,,&,Y-- 55;;Y>>>>@v@CC\EfEEEEFIJLLP"QReSUUU9V)WW`XX*[,[[[m]r]]^z^^__bb@ddSgUgkk-l/lAllm:n.vXvw xeygy!#DÆȆCW|Zfۏ'!)+, ڢУܣ>Iy+ٮ{}hj!#TQShTeBڼ@C$fkr2#rRs>@AIJMNX4?5 U>(.Zd!<_q2)0T   3XmXn  !!/R01133333337P7Q7788 ;H;IJKKeLxLMM5S7SSTTTqUzUVV5Y:YFY}YP]]_Q`llllllll-mLmqrr8|A|||f~k~_ )2dľ+ԏqsBFҟޣuӤդ(jFʧio=?EGв{}ekH|moKM RkSW4?#_xU`S\T`F;*?qEPAgj'uvx#kST"#!&[&0(:(((,:,?.C.-/4////111e2J5l5>6D66!7M7T78;:;<<==??v@x@@@OAAoEEFFGGHIkINNPPQHQQQfShSSSTT*U,UUUVVgWiWWWWWWXYYe\\]]%`'`ccdde1ffJg6jIjllnnBpRp7v9v€Ŋ ΌЌ>@,.ӓՓ<>isڗ  `̠ΠLP/H?SIJ ,jp{ݸMegs˺غ/>?R!!""$%'(*mo)./}3333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333bccd0= I :Q"D+4 La ""##[[SX IISSUUܠܠWWppA˺/!!""$%'(*mo)*,,./5EF!!""$%'(*+./|@/Cs}r~ҒQqfp=i'lHCo[](\-./01 'V/: 8/zZ/,0L*(LM3# 9*96'?/9*=͢t7RA,UcaEy&i9rR GX6DgYUfT[,ˆEn*-8t7(kxRR)[x ^`.^`.^`.^`. ^`OJQJo( ^`OJQJo( ^`OJQJo( ^`OJQJo(hh^h`. hh^h`OJQJo(ff^f`OJ QJ o(hHo^`OJ QJ ^J o(hHopp^p`OJQJo(hH@ @ ^@ `OJQJo(hH^`OJ QJ ^J o(hHo^`OJQJo(hH^`OJQJo(hH^`OJ QJ ^J o(hHoPP^P`OJQJo(hHnS^n`S56CJo(hH3.2.nS/ ^n`S56CJo(hH3.2../ / ^/ `56o(hH../ / ^/ `56o(hH.... / / ^/ `56o(hH ....  ^ `56o(hH./ / ^/ `56o(hH.ff^f`56o(hH()   `^ ``o(hH.........^`56o(hHSS^S`56o(hH.nn^n`56o(hH..nn^n`56o(hH... v^`v56CJo(hH ....77^7`56o(hH.nn^n`56o(hH.^`56o(hH()   ^ `o(hH hh^h`OJQJo(/^`o(GCJ,OJQJsHtH aJ_Ho(hHAnnex  SS^S`o(hH. SS^S`o(hH.. v^`vo(hH... v^`vo(hH ....   ^ `o(hH<>   ^ `o(hH<.> r/ ^/ `3*G5CJOJ%QJ%sHtHaJ_H4*6789:;<>*@EHH*KHS*TX[\]^Jo(hH Figure -  f^f`o(hH Table -   ^ `o(hH<>   ^ `o(hH<.>   ^ `o(hH<..> x^`xo(hH.... yy^y`o(hH ..... qXq^q`Xo(hH ...... ii^i`o(hH.......  a8a^a`8o(hH........  `^``o(hH......... <^`*@EHH*KHEHS*TX[\]^Jo(hH Figure .-   ^`o(hH Table .- ^`hH Article . 8^`hH Section . P^`PhH() `p`^``phH() P^`PhH) P^`PhH) ^`hH) P^`PhH. 0p0^0`phH.h@ @ ^@ `B*OJQJo(phhH^`OJPJQJ^Jo(-hpp^p`OJQJo(hHh@ @ ^@ `OJQJo(hHh^`OJ QJ ^Jo(hHoh^`OJQJo(hHh^`OJQJo(hHh^`OJ QJ ^Jo(hHohPP^P`OJQJo(hH <^`ZU6]7#E{MY_z1%4VDTF#G{Ma]&e7GWZj~4/9Qw~.l% Tem --CI`Jib]eWh{j_ ?MlEIUo) . e0 oN QQ Y  % (2 E Q A^    ( El !   KX ^ h 8x  Q2 3 c7 = c l y ">0;Qyy%.0Ooo$7o`Oc A> *9|kld*3Fuzz!,,@<k/s)h0:RO7[a c&HLKaq5wG3_yG Xkpp=+r3yy!c/$|$8,N\Z]v{I~-$D&b09aE}#CFJQ6tly%= : Z1 m !!w!?!`!3w"z}"B#QI#P#$$($6$c$2%T%Z%Nb% &&c&l&q&F''$'*'.'v'S{'` (*g(lt(~()L@) L)q)*7*1>1V\112O233q23}[3z34N44J4d-4l4?55;55<55:5D5F5X5si5{566n 666g 6d#6996:F6_O6:U6 _6e6<7P=7{7 8'8[)8-+8A8M9 9- 909RD9ZE9q9x9~9 : :9";<;[;];3s;(<.</<I5<M[<e<r<N=?=J=Q=n= >>c>>S>a>a>!?0?3?7@@:@}@}A9A(AQ!A$AQ`AdAwA||A&BAB_B`B*lBwBzzBC~4CMChC<D;DD/DIPDXDYD0dDiDAEbaEfEpnEsFW F8#F/)F0F4FdAFGTG~G]G`G{GS H HDH3$HtRH^HIIpIIWIpI}IaJy.JJJ`JolJvJc#K-'K:IKvQKWKZKSLhjLoL]uLX}L3 M3MJ@M-yM;N NM&NV&NNN ONQN0UN gN xN/OKOUP%VPWPvP Q8QQWQRR_RGRuRvSSk-S7jSNnSzSS>T8 T@ TT!T/T03TDTHTdRT(oT+ UnUAUWU^UfUoUe V$V OVmV>wV}VWg,WHWQWRX XLCXDXLX-rXY6Y%SYNZY]YbYlYGoYR}YQ0ZCZTZaZ)[=[)Q[_R[e[2\A\#\)\+\K-\O=\l\\e]] ]]K]X] \]\]a]j]^x^X^\^$+_`_|l_m_s_`_+`/`IG`'Q`%R`T`V`r`r`%a,a94a@a*ba%ya2bTb|c}c:c cz5c$:cmcd&d2d;dadqd}de5e;eWeae]fffk(f9fLfRfTfhVf\fafggg^gkg"g:g AgNMgVg"h Hhbhph iCij/)jAj VjbjjpjszjkRkG&kkSk"gkyk+l+lFl[lhl/jlmhm2!ve Secretariat4ECSS-Handbook-Template-Version5.6(24Aug2010).dottec-q6Microsoft Office Word@G@:@D@n1P0՜.+,D՜.+,D hp|  ESAP' DocumentSummaryInformation8,Macros'11VBA$11dirCECSS-E-HB-32-20 Part 8A Titleh@2J _PID_HLINKSECSS IDECSS WG ECSS DateECSS DisciplineAD6 5http://www.onera.fr/3t2http://www.man-technologie.de/3t/http://www.man-technologie.de/wv*http://www.dlr.de/"''http://www2.din.de/?_Toc289673334?_Toc289673333?_Toc289673332? _Toc289673331ECSS-E-HB-32-20 Part 8AECSS-E-HB-32-20A20 March 2011Space engineering0* pHdProjectQ(@= l sNN J< rstdole>stdoleP h%^*\G{00020430-C 0046}#2.0#0#C:\WINDOWS\system32\e2.tlb#OLE Automation`EOfficEOficEE2DF8D04C-5BFA-101B-BDE5EAAC42Egram Files\@CommonMicrosoft Shared\OFFICE11\MSO.DLL&#M 1q Ob LibraryKTemplate1> am paeP*rj c~| *\CNDocuments and Settings\All User@ pplicO DPata\)\s\ECSS-H@ book--V]5.6(24Aug2010).dotQFP¼ThisEEGBThisDQcumRnR 2 HB1ɸl,!("B+B NewMaAG wMaws 2 O U yb #!#b NewMacros#%VThisDocument&N_VBA_PROJECT PROJECT"(]    !"#$%T[O=xME@@L/C@LJ1 p+*i,0 8_ x|`z!"`T re`onta A &Project.NewMacros.comment0hDDH "    l 8 X `Fp$"(0B8  B   @  @  & ( 0"8 @ H dh     0@&P8.x   Z08P Th Zhx Z    ( \H    $  "    $  (    0 @  N` * F ( ,( *X D   * N hh*D H*6 >8*xF F 8 P&X    $    ( H X  h* "  ( 6 0 8 "@h"     (@H`h  px   @@08  @@"F  (  H(X ( ( ( ((8 `(h ,(   ((Pp&8@` hp   *  08 @ ^`    (L8  $V@  "  d n  f $ " H"h L 0 P p   N  !@! H! `!h!>x! !  ! J! ("68"p"4x" "" " ^"@#4`#&# # ## # #$n$<$$$$<%@% P%Vp%% % "% % % & && & 8&H& `&p&x&&&&&&&&&&& &' ' '('0'8'@'H'P'X'`'h'' ''']F:\AIT\ECS6_3_Paper4 directory of glossary and HBs2] ECSS-E-HB-32-20_Draft2_part1.doc@ current documentV$0 Replace_Style Makrocrof In case that the selected Text is in style "Standard" press Ctrl "," to replace style "Standard" with style "Normal Para" !"9Style NOT replaced (selections contain different styles)!A@$ !"Standard &%(e Normal Para &%( ("Style successfully replaced!A@$d5Style NOT replaced (Style is not of type 'Standard')!A@$kxopp: Converts the string so that it can be used for a bookmark'. 0 , " , 0$. , 0$  , 0$- , 0$$2 ._ '.  , 0$[ , 0$]e Does nothingd . , 0$ 6$4 '.k .'*i Create_Bookmarks Makro^ Creates bookmarks with readable names for equations, headings, figures, tables and references Saves cursor position !<!>': Deletes old bookmarks D &!@(B &!@(F 0 &!@!H8!1AQa 0 &%@!_Ref 0 &%@! EQUATION_ 0 &%@!FIGURE_ 0 &%@!HEADING_ 0 &%@!OLE_ 0 &%@! REFERENCE_ 0 &%@!TABLE_ 0 &%@B@Jk80TInserts references as fields --> bookmarks '_Ref012345678' are automatically created'0 L P &%N 0 0    PT XV 0$\Z^`b d B@Rk8 0 '0 '0 LTable &%N TableT fV 0$\Z^`b d B@R 0 '0'0 LFigure &%N FigureT fV 0$\Z^`b d B@R 0 '0'0 LEquation &%N EquationT fV 0$\Z^`b d B@R 0 '0@ Saves range of created fields !<.h :> !<! hB@j~ Performs a goto to the referenced bookmarks, checks which type, sets selection on first letter and creates adequate bookmarks'l 0 &!@!H 0 &%@!_Ref pn 0 &%@! B@ l 'l !" Unknown StyleA@$ !"Table:cellCENTER !"Caption:Annex Equatione !<!>> !<!> B@j !<< EQUATION_ l h%t!v$*  &!@B@r  % 1 !" berschrift 1 !" Heading 1 !" berschrift 2 !" Heading 2 !" berschrift 3 !" Heading 3 !" berschrift 4 !" Heading 4 !" berschrift 5 !" Heading 5e !<!>> !<!> B@j !<<HEADING_ l h%t!v$*  &!@B@r !"Annex1e !<!>> !<!> B@j !<<HEADING_ l h%t!v$$*  &!@B@r   !"Annex2 !"Annex3 !"Annex4 !"Annex5e !<!>> !<!> B@j !<<HEADING_ l h%t!v$*  &!@B@r  !" Beschriftung !"Caption !"Caption:Annex Figure !"Caption:Annex Tablee !<!>> !<!> B@j !<< l h%t!v$* &!@B@r !" Ref_Heading !" Ref_Annexe !<!>> !<!> B@j !<< REFERENCE_ l h%t!v$*  &!@B@r !"$list: !"$NOTEe Does nothingdUnknown Style: !" A@$kxkph Deletes '_Ref' bookmarks 0 &!@!H 0 &%@!_Ref 0 &%@B@Jk  Deletes the references hB@H B@J Displays message boxBookmarks successfully createdA@$o@ ! Create_Hyperlink_Reference Makro/ Creates a hyperlink for the selected reference Exits if selection is empty !<!> !<!The selection is emptyA@$|H k@  Saves selected text]P !d'z Retrieves section name'|'~ z['| zFiguree'| zTablee'| zAnnexe'|dP '|k@ 0 | z" z 0$0 z 0$9  z 0$A z 0$Z  0'~d z '0kh ` 9 Exits if selection does not contain a valid section name ~3The selection does not contain a valid section nameA@$| k : Selects document name which depends on the section number z | ~ |  $']h $0 $9  X'  LT ECSS-E-HB-32-20_Draft2_part1.doc' LT ECSS-E-HB-32-20_Draft2_part2.doc' LT ECSS-E-HB-32-20_Draft2_part3.doc'!-LT ECSS-E-HB-32-20_Draft2_part4.doc'.?LT ECSS-E-HB-32-20_Draft2_part5.doc'@QLT ECSS-E-HB-32-20_Draft2_part6.doc'S ECSS-E-HB-32-20_Draft2_part7.doc'nhd`% for annexes which are only in part 7 ECSS-E-HB-32-20_Draft2_part7.doc'k Creates bookmark name] z[ z. EQUATION_ z$* ' zFiguree z$*' z[e REFERENCE_ z$* ' zTablee z$*' zAnnexeHEADING_ z$$* 'dHEADING_ z$* 'k'   ! G'j  # if HB is not already open, open it A@  B@k $B@'' 0 &!@!HW try to find bookmark in the list of bookmarks in "ECSS-E-HB-32-20_Draft2_glossary.doc" 0 &%@! ' 0 &%@!'k 0  $B@  !<   z  &!B@r    $B@BkH $B@Hyperlink gesetzt!A@$d  $B@B $B@Hyperlink NICHT gesetzt!A@$%(i)iA@(>open dialog for setting the hyperlink manually ( + )k`oX^ Based on the current document (defined by "aktuellesdoc") and based on the current selection,h this macro tries to set the bookmark referring to "ECSS-E-HB-32-20_Draft2_glossary.doc". If successful,_ a Messagebox is displayed. If not, also a Messagebox is display and the dialog for setting the hyperlink manually is opended Exits if selection is empty !<!> !<!Please select a text.A@$|hk`F replace characters which will not be part of the bookmark name by "?" !d ?$' .?$' -?$' /?$' %?$' $?$' $?$' $?00 if the very right character is a "?", delete it   $'k  6$4''   !#ECSS-E-HB-32-20_Draft2_glossary.docG'j  D if ECSS-E-HB-32-20_Draft2_glossary.doc is not already open, open it A@#ECSS-E-HB-32-20_Draft2_glossary.doc B@k#ECSS-E-HB-32-20_Draft2_glossary.doc$B@'' 0 &!@!HW try to find bookmark in the list of bookmarks in "ECSS-E-HB-32-20_Draft2_glossary.doc" -?$' 0 &%@!_?$[A-Z] ' 0 &%@!   ' 0 &%@!'k 0  $B@  !<#ECSS-E-HB-32-20_Draft2_glossary.doc  !d &!B@r #ECSS-E-HB-32-20_Draft2_glossary.doc$B@B $B@ Link gesetzt!A@$d #ECSS-E-HB-32-20_Draft2_glossary.doc$B@B $B@Link NICHT gesetzt!A@$%(i)iA@(>open dialog for setting the hyperlink manually ( + )k0o( comment Makro !B@ !!B@ ! are required9d5(d9 9999999qH !B@ !B@ !!B@ !has to 9d5(d9 9999999q !<< !B@r Normative?d B@ B@o@8Attribute VB_Name = "NewMacros" Const arbeitsverzeichnisF:\AIT\ECS6_3_Paper" ' directory of g lossaan d HBsktuellesdocNGS-E-HB-32-20_Draft2_part1.#[_ ' curreHnt um Sub Replace_Style() '  MakroIn cas@e thate sel\ed Text sin s& "St`ard" press Ctrl "," to rÃ;withA!Normal ParaN h If (S1nt.W EQUATION_o'oomeFIGUREO AHEADING__4m "OL; REFERENCu "TABBbsD,$OAQ'In sertsh6 a:ields -$-><'_#012345678'Pe autom 1000 A@{i <= 12g@ TF:= ,Iq! KindAs HRelve`WtM0X, :=9iF)s AsHr@link:=qA,cludeP4N:=Fap,M;ZSsv{Q Seborp`J:="> qpcQi + 1Gd5УTQ] ѶP`.OceM".OnlyLa8bel!tr`2je) yti3"Fbtcence._.8- ETpe8&-pRE0(<Position:=False, SeparateNumbersa_ orString:=" ":i =@ i + 1$Next ' Saves range of crend fields$Set referenc+"=lec.R77%!.0 Start:=sPoint, E@nd:=Se @.D' Performs a goto heBd bookmarks, checks whi@ch typs ets s2 onhrst letter andÄt0dequy(Bj0For= 1 To A|veDocu@ment.BC.0CounIf( In((i ).NamV"_`Ref")8@henCwH[GoWhaTwd, := A8jdž.gStyle Is Nodth T' MsgBox ("Unknown@~i ") EP= "Table:cellCENTER" Or G % CapAnnex Eq@")et G~.­Ԫ5A'^.pAdd BEm"EQUATION_"1Convert_y(jFbr(j).Resu\lt+a7$achrift 1B+H!<Head</ 2  3  4  5 f0_Rrէ_R+_R"HE ADING?Rlds?RMv M"u"sfuu"Midyu, 7)uu/3 ;"0e/.+!+~TTO~T^STOT|s.T juRBesTung?r-tiD0[lFigure pRto Fon/{/%Д_l4/IȰ#WREFERENCEZgIZTQLb&, 1, 5"list:`p4r0NOTE' Do@n1q: V`lIf` Dt 'Ѹ'5/1pPep -$! @ÿƾ tiߪܱ{C`isplays messabox sucsfully5 q Sub @ C _HprlinkB(' '/<# Makro7h ed"A' Exiifis empty(Xo`t} ) The selection is empty") Exit SubDEnd If 4' Savesed text4Di m,T* As String>Ded= S."' Re7egnamefirstPos"i= 0laAIf In( |, "[") = 1 n} -2 Else$@Figure&8&Tabl#&7&AnnexL=C1DCFor i@SKOTo xLen]S@eComp(MidLgi, 1)i0/> -1 A 9 3he(8QUATION_"bConvert_0nPZtTA!J\Wrzp REFERE(NCE g } t o_  `ome ["HEADING g 7)HS' ? ? Q qFou= Fa@IEaxoc- DTzs &p@.1.=f|l UTr>uT:c<> q܈'HB !al0:dy oeЁ,R it ChangeFilDeODirpory arbei$tsP3zeЅnikH v .1  :^=)N ICf(y).Awv`DxstrE01"tմe.BHs.Ctq^1ep#a' t@to@PRlis`t of unRtRglossa +  Sub  CrJe__Grsary(@' ' Based oncurr  (definby "Io2 abQselevon,this macro tries to9bookmark referr>o "ECSS-E-HB-32-20_Draft2_g..'". succ@essfula M@ageb@displayed not, also A4?^Sd3eqded]x' Exi`ts if:B A emptyCIf (SI.R.Start =6 t) Ple@`5text."A" BdE '.#ce characters which will & bHe pof 6ne B?" >sdtrReb TA, " "?/@.trm-/%Chr(30)a146@?Right(1)&"?"b<4 g'aH!Rvery rg5AJa , d@Ite itc1 Lefg Len) - 1RStrConvvbUp@CNCFou`K= FlF EaIu In `!.a ~Fc$ Tru N?Lᖃ <> !h+c-aaDaldy },*.cFileOQDiro6arbe@8ze`knis,f".a& !:=oc$oA (=x =Z= "[i|e."BT]s.CP!t To 1 StePp -1'`yS`fd ihlpist @GuTn~ ? a J,%I7"{C2 O js7|+@_Cx"[A-Z]'` Like[SOlX2+ /Q1f= o $b4i3=3 <(y_ ƈs.Add Anchor:=lo, r|:= _ / / Poh, ScreenxTip 6pQjToD#6oos!bϳϳ .soϲòL "_ _ _ /"R ,s'QX1~comQAt`buuD.VB_ProcDataInvoke_FuncC"j_.NewMQpmaFals pMatchCaseWho0leWos;Wihldcs@ SoundsLikb!Alla EEnd WithtSelection.Comms.Add Range:= 0Type:="Norive?Escap@eKey @Sub xME (S"SS"<:1TemplateProject.ThisDocument8(%HxAttribute VB_Name = "ThisDocument" Bas1TemplateProject.hGlobaBlSpac~False Cre atablPr@edeclaI"dTru BEx0poseDeriv$Cust0omizC1ID="{A6EA3FBB-2437-400F-B11A-75EA7A993796}" Document=ThisDocument/&H00000000 Module=NewMacros Name="Project" HelpContextID="0" VersionCompatible32="393222000" CMG="9A98702B1D2F1D2F1D2F1Day  *\G{000204EF-0000-0000-C000-000000000046}#4.0#9#C:\Program Files\Common Files\Microsoft Shared\VBA\VBA6\VBE6.DLL#Visual Basic For Applications*\G{00020905-0000-0000-C000-000000000046}#8.3#0#C:\Program Files\Microsoft Office\OFFICE11\MSWORD.OLB#Microsoft Word 11.0 Object Library*\G{00020430-0000-0000-C000-000000000046}#2.0#0#C:\WINDOWS\system32\stdole2.tlb#OLE Automation(*\G{2DF8D04C-5BFA-101B-BDE5-00AA0044DE52}#2.3#0#C:\Program Files\Common Files\Microsoft Shared\OFFICE11\MSO.DLL#Microsoft Office 12.0 Object Library*\CC:\Documents and Settings\All Users\Application Data\Microsoft\Templates\ECSS-Handbook-Template-Version5.6(24Aug2010).dot*\CC:\Documents and Settings\All Users\Application Data\Microsoft\Templates\ECSS-Handbook-Template-Version5.6(24Aug2010).dotsNN  sNN ThisDocument024d4d3877ThisDocumentNewMacros034d4d3877NewMacrosU=8tr@al $΄GXUHkl4WordkVBAWin16~Win32MacVBA6#Project-stdole`NormalOfficeu ThisDocument< _Evaluate NewMacrosjarbeitsverzeichnisb aktuellesdocE Replace_StyleW SelectionZStylepMsgBoxRActiveDocument\Styles pConvert_String.stringToConvert resultString\i`Asc!uStrConvx' vbUpperCasek.Create_Bookmarks startPointRange Start Bookmarks?nDefaultSortingz wdSortByName\ ShowHiddenqsCount0vDeletexItemzGetCrossReferenceItemswdRefTypeNumberedItemGInsertCrossReference  ReferenceType- ReferenceKindwdNumberRelativeContextE ReferenceItembStrInsertAsHyperlink&IncludePositionYSeparateNumbersSeparatorStringwdOnlyLabelAndNumberC referencesSetRangejaWhatCwdGoToBookmarkJAddrFields7ResulturCreate_Hyperlink_Reference} selectedText$[ firstPosition lastPosition sectionName+ documentName sectionNumber bookmarkName'Found+doc DocumentsChangeFileOpenDirectory=FileNamejActivate| strbookmark Hyperlinks:Anchor#rAddress SubAddress+M ScreenTip TextToDisplay SaveChangestwdDoNotSaveChangesԇSendKeysNCreate_Hyperlink_GlossaryHselstrReplacefChrK~Right selstr2commentHsFindnClearFormatting) ReplacementForwardWrapWywdFindContinueBP MatchCaseMatchWholeWordXMatchWildcardsMatchSoundsLike0MatchAllWordFormsExecuteYComments)TypeText EscapeKeyDocumentjTemplateProjectE`   $2F" DPB="4341A9825383538353" GC="ECEE0671061B071B07E4" [Host Extender Info] &H00000001={3832D640-CF90-11CF-8E43-00A0C911005A};VBE;&H00000000 [Workspace] ThisDocument=0, 0, 749, 626, NewMacros=48, 52, 554, 333, Z ThisDocumentThisDocumentNewMacrosNewMacros  FMicrosoft Office Word Document MSWordDocWord.Document.89qPROJECTwmdGCompObj!fqm<5mMm`mfmnnx?n Rn\n2oEoYo@gonyo pp'p1pJpKpRpSpop=)qTqxexzx;yz$y 7y5CyEyXy(~y)z3z6z\;z?znEz^GzKzonzzzW}zz {3{K{L`{|{j{||,|-|6|7|U|Et|.}1}e}}~~%F~I~J~wO~1V~X]~V~~ XWw8O.ZZ{|hTfbiio/[kxk56?gdkF~W~3Lc,GD|Xa@!1LOjdny -9(:;E&GP3Q{!$Bo7>)1+#\2LfN QqVa#".1M_h'*<BtGwa[j6tGvf&Y;\cj,(W,JSv%V&5{5=biX .* ,x]qM h4OZ#bv@EV(pMI`Vj!{$ f>cd}*: BQauza;<hYhzWggHhkzZ 0BXFJ}2C5j@~AMN`#/;0266COYV|)O^ba+0J2X? HadIfLO|\gjxO4PVbh{ +\4}$.D[jY;56FAXaagt z]gy>IOrSl& 15MRX 9ij:;Dk4> ],|B{n ^"R'"^l@wpw6)s ^*;> K L*03@/AQ+hh d@V^Ky3\QST^j1ns! 5IO|Aecsx]Idt$+E`cd$P/LM`}g 1=GoI)8\im E&(AVC{ Q')3>Tvvw *2/11c9=~Pir6+p0<,^ |:<=V k# $a4IeB(w._6$;dQbphz%AQRVdpM$.+'=DK3|i(.'GgNL-3=WIEKhz:?4C.Q]`|Rz?i`iIy7VP)Vn^]o|NTvaww4xc \o$&/8F\d#,-J@` L{S|~ qUs)69MR-.VlouenTv{yp &z)C&\bFWTte}mxtu;B,]f_ ?TrZPoo} 3?%NRaSdit~?ra<b9mn{=}}HP_lk7t> RUOhpbxBCRma OKZ~be`p :o2FqOPak{nEqKqX$) R:%<]cas,/_Lp\!Ledrmqw-x~6#KM__v>4 !H"7CQN'XoZ|7\^ p=yARtn&]p [ekt} 1#E0M} ] J#3mGOWacelXsZz +  B P Q X 7 G H O 8 H I P    !$'** #( #" UK M  V ;;V ;;V ;;V ;;V;;"Project.NewMacros.Create_Bookmarks,Project.NewMacros.Create_Hyperlink_ReferenceProject.NewMacros.Replace_StyleProject.NewMacros.comment+Project.NewMacros.Create_Hyperlink_Glossary PROJECT.NEWMACROS.COMMENT PROJECT.NEWMACROS.REPLACE_STYLE "PROJECT.NEWMACROS.CREATE_BOOKMARKS +PROJECT.NEWMACROS.CREATE_HYPERLINK_GLOSSARY,PROJECT.NEWMACROS.CREATE_HYPERLINK_REFERENCE@Dj3j5wLwMwwwwwkwlwpwqw`@`<`@`X`@``(@``@`z`@``@` @UnknownelaG:Ax Times New Roman5Symbol3& :Cx ArialK@Palatino LinotypeMCentury SchoolbookA& Arial Narrow5& >[`)TahomaoNewCenturySchlbkCentury SchoolbookW  Sans NarrowCourier Newg& AvantGarde Md BTCentury Gothic71 Courier?5 :Cx Courier New7&@ Calibrig&AvantGarde Bk BTCentury GothicKTimesNewRomanPSMT;Wingdings;" Helvetica"1 hi"&${&P0P0Ix4dPP&> >qXR 062 |C:\Documents and Settings\Stephen Bury\Application Data\Microsoft\templates\ECSS-Handbook-Template-Version5.6(24Aug2010).dotECSS-E-HB-32-20 Part 8A0Structural materials handbook - Part 8: GlossaryECSS Executive Secretariattec-q1e5c33a54df4072             D     C    B