Asphalt specifications for roads
[DOCX File]GENERAL
https://info.5y1.org/asphalt-specifications-for-roads_1_58f954.html
Asphalt used in an asphalt pavement is addressed in Specification 510 ASPHALT INTERMEDIATE COURSE. Details of the location and extent of asphalt work are either summarised at Annexure 504A, or are indicated on the Drawings. Details. The works shall include surface preparation, supply of materials, production, hauling, placing and compaction of asphalt to the areas as shown in the Drawings, or ...
[DOCX File]Sealcoat Manufacturers | Pavement Sealer Manufacturers
https://info.5y1.org/asphalt-specifications-for-roads_1_f02497.html
ASPHALT PAVEMENT SEALCOATING SPECIFICATION FOR PARKING LOTS. Specifier’s Notes: This Asphalt Pavement Sealcoating Specification is furnished as a guide for specifying Asphalt Repair, Sealcoating and Striping of Asphalt Pavement Parking Lots. It is written in the CSI 3-Part Format and must be edited to suit the particular needs and budgetary requirements of a given project and its respective ...
[DOC File]Specification selection guide
https://info.5y1.org/asphalt-specifications-for-roads_1_c332d5.html
(2)State of Wisconsin Standard Specifications for Highway and Structure Construction. P401-015 (Superpave) to supplement Airport Spec Book. (5)Exception – For Federally funded PCC pavements designed for
[DOC File]SECTION 407 - VicRoads
https://info.5y1.org/asphalt-specifications-for-roads_1_405685.html
SUMMARY OF ACTION REQUIRED WHEN PREPARING ASPHALT SPECIFICATIONS. General. The following is a check list of activities and information required before completing an asphalt specification: 1. Obtain a copy of the pavement design report for the job to establish the recommended pavement composition and the type and nominal size of asphalt required for each layer. 2. If no pavement report is ...
[DOCX File]Reference Specifications for Civil Engineering Work 2001
https://info.5y1.org/asphalt-specifications-for-roads_1_04f704.html
Mix substitution: Do not substitute BCC mixes with the alternative Queensland Department of Transport and Main Roads (DTMR) dense graded asphalt mixes listed in Table 4.1, unless prior approval is obtained from Brisbane City Council. The same binder type as the BCC mixes are to used in substitute mixes. Alternative DTMR asphalt mix: Where approval is granted by Brisbane City Council to ...
[DOC File]CITY OF THUNDER BAY CONTRACT DOCUMENTS MANUAL
https://info.5y1.org/asphalt-specifications-for-roads_1_b4945b.html
Echelon paving is required on roads with four (4) or more through-lanes for top lift. Only one (1) cold longitudinal joint is permitted on top lift paving of City streets. PREPARATION FOR PAVING. OPSS 310. Patch holes and pad depressions, in existing asphalt by hand, grader or spreader prior to paving.
[DOC File]32 12 16 - Asphalt Concrete Pavement
https://info.5y1.org/asphalt-specifications-for-roads_1_88064a.html
Use this Section to specify asphalt concrete pavement required for parking lots, driveways, and access roads. This Master Specification Section contains:.1 This Cover Sheet.2 Data Sheet - Definitions.3 Specification Section Text: 1. General. 1.1 Section Includes . 1.2 Related Requirements. 1.3 Reference Documents. 1.4 Submittals. 1.5 Mixing Plant Qualifications. 1.6 Testing and Inspection by ...
[DOC File]Hot Mix Asphalt Concrete ( In-Place)
https://info.5y1.org/asphalt-specifications-for-roads_1_f9238d.html
SPECIFICATIONS. VENDOR PLACED HOT MIX ASPHALT CONCRETE . SCOPE: This specification covers the placement of Hot Mix Asphalt pavement on roads in Tompkins County. The work included within these specifications shall include, but not be limited to: All materials, labor and equipment necessary to provide, transport, place, and compact Hot Mix Asphalt pavement. All maintenance and protection of ...
SECTION 321216 - ASPHALT PAVING
Asphalt concrete surfacing shall conform to Section 39 of the CALTRANS Standard Specifications. Paving shall be done under suitable weather conditions for such operations. Temperatures shall be above 50 deg F (10 deg C) during placement of paving, and shall be above 40 deg F (4.4 deg C) during placement of asphalt treated permeable base. Rain or other inclement weather will be cause for ...
BITUMINOUS HOT MIX SPECIFICATIONS
Asphalt concrete shall be Class E2, in accordance with “Standard Specifications for Roads and Bridges”, latest Edition, and Section 890. The asphalt cement shall be PG-Grade 58-28 rated oil. The asphalt cement per ton will be in accordance with the South Dakota Department of Transportation “Standard Specifications for Roads and Bridges”, latest Edition . The contractor shall provide a ...
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.