Steel roll bar tubing
[DOC File]141 SPEEDWAY
https://info.5y1.org/steel-roll-bar-tubing_1_dd5b65.html
Roll bar padding required in driver’s compartment. ... Minimum of 2”x 3” rectangular tubing must be used in place of rear frame rails, placed no further back than the rear spring pockets and no longer than factory specs. WEIGHT AND BALLAST: Added weight (ballast) may be steel or lead. All weights must be securely attached for inspection ...
nebula.wsimg.com
Reinforcing plate, tubing, or steel angle on the inside of the rocker rails is required. Main hoop of cage must include a diagonal reinforcing bar. Roll cage must include a minimum of 3 door bars per side, connected with spacing bars between each door bar. Driver’s side bars must be arched away from the driver’s seat area.
[DOCX File]ARCAT, Inc.
https://info.5y1.org/steel-roll-bar-tubing_1_7f71df.html
Mounted on 1-5/16 inch (32 mm) O. D. hot rolled steel tubing, 13 gauge steel tubing for doors up to 10 feet, otherwise 11 gauge up to 12 feet (3658 mm) wide. Support brackets: 3/16 inch (5 mm) thick structural steel angles and 1/4 inch (6 mm) thick steel diagonal brace welded in a triangular form to support ends of drum assembly.
[DOCX File]www.antiochspeedway.com
https://info.5y1.org/steel-roll-bar-tubing_1_6e27a7.html
All main cage roll bar. material must be a minimum of 1 3/4′′ .090′′ wall steel tubing No thread pipe fittings allowed. All roll. cage welds must have a minimum 2′′ x 11/2′′ x 11/2′′ x .125′′ steel gussets. All roll bar structure. exposed to the driver and passenger must be padded with approved padding . Roll bar ...
[DOC File]1 - Lee County Speedway
https://info.5y1.org/steel-roll-bar-tubing_1_ffa716.html
Radiator core support may be removed and replaced with 2”x2” angle iron or 1 ¾” roll bar tubing. Must be in line with, or behind radiator and vertical. Top support can go from fender to fender. Angle brackets rearward must stay in front of A-frame. One 1 ¾” pipe between frame rails directly in …
Lake Ozark Speedway
: Must be constructed of two inch by two inch square steel tubing, or minimum 1.75 inch round tubing - with minimum 0.083 wall thickness. Minimum wheelbase of 103 inches, maximum 105 inches, both sides. 3. ROLL CAGE: Main roll cage must be at least 1.5 inch O.D. tubing with minimum wall thickness of …
[DOCX File]141 SPEEDWAY
https://info.5y1.org/steel-roll-bar-tubing_1_09465d.html
A. Frame plating material (4” x 1/8”) flat strip steel. B. Roll cage main hoop set back 82 ½”, measured from center of lower ball joint to back of main hoop tubing. No. portion of the seat may extend beyond 80” from the left lower ball joint. C. Mandatory . X-brace, (Choose 1 material, no mixing).
[DOC File]1 - Lee County Speedway
https://info.5y1.org/steel-roll-bar-tubing_1_3afd87.html
Radiator core support may be removed and replaced with 2”x2” angle iron or 1 ¾” roll bar tubing. Must be in line with, or behind radiator and vertical. Top support can go from fender to fender. Angle brackets rearward must stay in front of A-frame. All bodies must have original steel firewall.
[DOCX File]ARCAT, Inc.
https://info.5y1.org/steel-roll-bar-tubing_1_f14d9b.html
Frame: 2 inches (51 mm) welded structural steel tubing. Threshold: 1/4 inch (6 mm) thick flat steel bar maximum. ADA compliant. Frame: shall be mounted onto 3-piece structural steel guides. Guides: shall be roll formed 10 gauge galvanized steel channels. Locking: Hand chain lock: Chain keeper mounted on wall for chain operated doors.
Nearby & related entries:
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.